Cisco Switching/Routing :: 3650x - Way To Enable PBR?
Jun 14, 2011
I am trying to enable policy based routing on a new 3560x switch.The device has the following code c3560e-universalk9-mz.122-55.SE1.bin and the IPSERVICES license
I can create the route map in global config mode but when I try to enable pbr under the required interface the commands are not there.therefore I am typing ip policy route-map "name" the word policy does not show up in the interface config mode. I have also change the sdm profile to routing this has not made a difference.
[code]...
View 13 Replies
ADVERTISEMENT
Jan 31, 2012
I'm not able to set the mtu on an SVI or routed gigabit port on either model. they are running 12.2(55)SE4.
It comes back as "% ip mtu is not supported on this interface".
Also, is there any reason why when the "ip tcp adjust-mss", (set to lower than default) is applied to the egress SVI on a 3750 or 3560x, the mms value of the SYN packet is not adjusted when captured at the receiving end? It seems as if the setting does nothing.
View 3 Replies
View Related
Mar 28, 2012
1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
View 2 Replies
View Related
Mar 27, 2012
I have purchased these two switches from ebay as a test lab, I plan to connect them up via a gigastack modulecable and enable ip routing on the c3550 and vlans to talk to each other.
I'm very much a procurve person and really need to get into the cisco switching.I will want to trunklacp between the switches - whats the process is setting that up on cisco switches?
View 1 Replies
View Related
Mar 23, 2013
I need to enable multicast routing on 2960s but the command "ip multicast-routing" isn't available on my release (12.2.(55)).
From which release this command is available?
View 1 Replies
View Related
Apr 3, 2013
Have a 3750X running at the moment and has about 30 vlans all connected and just use the ip route global config command to enable routing. Plan is to switch out to the 4503E, with IPBase license. When ever I issue the same command, and do a show run its not there. I get no error when I issue the command either. And yes I have rebooted. Do I need to use RIP or OSPF routing? When I do a show ip route the screen looks the same with all the codes, though gateway of last resort isn't set even though I do have ip route 0.0.0.0 0.0.0.0 a.b.c.d in the config. Or is ip routing just enabled by default?
View 6 Replies
View Related
Apr 19, 2013
I have been trying to enable L3 intervlan routing on C2960S Switch with ip routing command and that was the output from the Switch: [code]
View 6 Replies
View Related
Feb 14, 2012
How do I enable SSH on 4507. I do not see "ip ssh ..." commands config#ip ssh (I do not see "ip ssh " commnd)
Do i need to enable something else?
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
View 1 Replies
View Related
Mar 17, 2013
I have a 370 with C3KX-NM-10G module & i want to enable NetFlow on it did the specified configs
Step 1 Flexible NetFlow Flow Recordsflow record miketestmatch datalink source-vlan-idmatch datalink dot1q prioritymatch datalink mac source-addressmatch datalink mac destination-addressmatch ipv4 versionmatch ipv4 tosmatch ipv4 ttlmatch ipv4 protocolmatch ipv4 source addressmatch ipv4 destination addressmatch transport source-portmatch transport destination-portmatch interface input physical snmpcollect interface output snmpcollect counter flowscollect counter bytescollect counter packetscollect timestamp sys-uptime firstcollect timestamp sys-uptime last flow record miketestegressmatch datalink destination-vlan-id match datalink dot1q priority match datalink mac source-address match datalink mac destination-address match ipv4 version match ipv4 tos match ipv4 ttl match ipv4 protocol match ipv4 source address match ipv4 destination address match transport source-port match transport destination-port match interface output physical snmp collect interface input snmp collect counter flows collect counter bytes collect counter packets collect timestamp sys-uptime first collect timestamp sys-uptime last Step 2 Flexible NetFlow Flow ExporterFlow exporter export-to-samplicatorDestination 10.1.1.8source Vlan1Transport udp 2055option interface-table timeout 60 Step 3 Flexible NetFlow Flow Monitors# Tie the Flow Monitor to the Flow Recordflow monitor mikektestrecord miketestexporter export-to-samplicatorcache timeout active 60flow monitor mikektestegressrecord miketestegressexporter export-to-samplicatorcache timeout active 60
& Applied it to g1/1/1 but without any luck , if netflow works on the
TenGigabitEthernet1/1/1 &
TenGigabitEthernet1/1/2
Only i have four switches stacked and nothing plugged to the
C3KX-NM-10G module
View 1 Replies
View Related
Mar 18, 2012
I use IOS Software, ME360x Software (ME360x-UNIVERSALK9-M), Version 12.2(52)EY2. I not found the command "ipv6" on global and interface configuration.
View 2 Replies
View Related
Nov 7, 2011
I am trying to configure a 3750 48 port switch and having trouble with getting it to see the sfp. I just want to set up the router with a pretty basic set up since I am using it for a ping test between 2 buildings, via fiber. How I can enable the sfp port?
View 3 Replies
View Related
May 8, 2013
I have 4506 with below sup, my requirement is to enable netfolw , but as i came to know that it is not supported in this sup, is there any additional option which can be explored to get the netflow working without replacing sup.
Card Type Model
-------------------------------------------------------------+-----------------------
Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
View 4 Replies
View Related
Oct 26, 2009
i am having 2950 switch. Now i login through telnet but as per the company standard i have to login through ssh. Is there any possible to enable the SSH in 2950. Any IOS supporting this operation.
flash:/c2950-i6q4l2-mz.121-19.EA1c.bin
View 8 Replies
View Related
Jan 14, 2012
On my 2650 Router it just has only Telnet password.It has no enable mode password set.After reboot it is goes to prompt mode BB.I am unable to go to enable mode .how can i go back to enable mode on this router?
View 13 Replies
View Related
Jun 7, 2012
I have a 2960G that I keep on the bench as a work switch. I assigned an IP address to it. The techs have had trouble imaging workstations using GHOST. Do any config changes need to be made to enable multicast to work? Everything is in VLAN1 at this point and the GHOST server is also the DHCP server.
View 1 Replies
View Related
Nov 3, 2011
To enable netflow export on ASR1001, do i need the firewall feaure license or not ?Docs are not really clear, NBAR requires FW license, but i am unsure about Netflow?
View 1 Replies
View Related
Jan 19, 2012
i have configuration my network infrastructure with the asa5505 like on image. i want that my users from lan 10.13.10.0/24 can to access to my LAN 192.168.0.0/24. can i use just routing or i must to use site to site VPN. how can i do it? how configure my asa 5505.on my LAN1 there's DHCP. From LAN side of my asa5505 i must disable DHCP.In my LAN1 i have DNS,Domain Controller. The users from my LAN3 need to access to LAN1 because of authentication and access to resources and programs. i attached my picture with configurtion.
View 2 Replies
View Related
Feb 11, 2013
How do i enable InterVLAN MultiCasting. I have a WS-C3560G-24TS as my core switch and it does InterVLAN Routing. I have a Server VLAN (70) and Workstation VLAN (71). I have a server that i have set up to deploy images to computers. Up to this point i have only done one computer at a time, so unicasting was ok. I would like to be able to Multicast to multiple computers, but am unsure what i need to do on the switch (if anything) to enable this.
View 2 Replies
View Related
Jan 30, 2013
We have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
View 1 Replies
View Related
Jan 6, 2013
I have been trying to get the http server enabled so I can access Cisco Network Assistant. I have my interfaces configured but for some reason the server in not running, port 80 is still closed. [code]
View 2 Replies
View Related
Oct 20, 2012
How to enable UPNP on CISCO routers - 36XX , How can I simualte UPNP connections.
View 2 Replies
View Related
Oct 27, 2010
I am planning to enable MAC address filtering (one port on 4510 & another 3560). I want to allow only that MAC address to communicate via that port with the rest of the network and internet.
4510 has PC connected and 3560 had polycom connected. [code]
View 5 Replies
View Related
Dec 26, 2011
I want to enable SNMP and track the status/ of the interfaces in switches.
We have Two- cat 3750 (L3 switch) and Nine-cat 2960 (L2)
How to configure the SNMP. any Links provides the required info with an example of configuring snmp will be really useful.
we have OPEN NMS, SPLUNK, MYSQL monitoring tools.
View 1 Replies
View Related
Sep 23, 2012
I have a hub and spoke WAN that conisits of one core location with with a 6500 and nine other buildings using 4006 Catalyst that conenct back to the core via dual gig fiber. We are using EIGRP at each location as well as the core. I was tesing something at one of our buildings decided to hang a 3750 off the 4006 and enable the same eigrp process on the 3750 that is enabled on the 4006 and 6500 (EIGRP 1).
1. All the routes that the 6500 knows about are advertised out to each of the nine locations.
2. The 4006's are all advertising thier directly conencted routes to the 6500.
Onto the location I was testing at:
The 4006 where I was testing at has four vlan interfaces enabled and they are in an UP/UP state. The ip routes from the 4006's directly conencted vlan interfaces propogate to the 6500 at our core location and the 6500 sucsefully propgates these learned routes to all the other 4006's.
This past Friday I configured a 3750x with two /22 vlan interfces and one physical gi port with an IP address and also configured on Ethernet port on the 4006 with an IP address in the same network block as the 3750x gi interface (a /30 netowrk block). I saw both interfaces come up and EIGRP sucesfully established a neighbor adjecency between the 3750x and the 4006.
I noticed that the 3750 advertised out all of it's directly conencted routes to the 4006 and the 4006 advertised it's directly conencted routes to the 3750. However, the 4006 did not advertise any of the routes it had learned from the 3750x to the 6500 and nor did the 4006 advertise any of the routes it had learned from the 6500 to the 4006. My suspicion is that the "eigrp stub connected summary" statement is enabled on both the 4006 and 3750 thus prevenintg them form advertising out any routes other than thier directly conencted routes. Can any of you verify that I'm either correct or inccorect about this?
here are the eigrp statemnets from the 6500 and 4006:
6500:
router eigrp 1
redistribute static
network 10.0.0.0
network 172.16.0.0
network 172.17.0.0(code)
View 2 Replies
View Related
Oct 31, 2012
My engineer onsite can't get into enable mode on his 2911 router. I've seen this before but I can't find out how I fixed it.
He gets an error saying : no password set
Here is the config:
Router#sh run
Building configuration...
Current configuration : 1784 bytes
!
[Code]....
View 3 Replies
View Related
Feb 12, 2013
We have CISCO ASR 1002 router on our DC, I want to enable TACACS on this router.what is the usage of key, we need a separate key for every device? or. [code]
View 9 Replies
View Related
Dec 7, 2011
How do I enable ports 3 and 4 on this supervisor module? I can only get ports 1 and 2 to work by default. I have a standby Supervisor in SSO mode. I'm running IOS 15.0.2SG
View 2 Replies
View Related
Feb 19, 2013
In my ongoing project i need to monitor cisco 3750-X port status (uplink/downlink) i.e. whenever there is some problem at a specific port. I need to monitor it through an OPC server and right now what i am doing is as follows: i am using Kepserver and i have added SNMP driver in it for that purpose i am not a networking expert but what i have learnt till now is that SNMP agent (that resides in switch) delivers the status of MIBs to SNMP manager ( which in my case is kepserver (opc server)) for the above purpose i am adding IF-MIB to monitor OID 1.3.6.1.2.1.2.2.1.8 (which shows port statuses) but when i add that in OPC server then it indicated that this OID is not available in the Switch ( it might be disabled) so i need to ask if there is any way to enable OID's in a switch,
View 0 Replies
View Related
Mar 25, 2012
My current production network is setup using VTP in Client mode, and I am looking to enable VTP Transparent so I can enable the extended VLANs. My main question would be, would enabling VTP Transparent on my 6509 affect all of the access switches it is connected to? And if so, would changing all of the access switches to VTP Transparent allow them to regain connectivity quickly with little downtime? Or is there another way that I should be handling this situation to enable the extended VLANs?
View 2 Replies
View Related
Nov 22, 2011
I was wondering if i can enable url filtering on my 2691 or 2651XM routers so that if someone visits any website i can see that under router logs. right now i am using kiwi syslog that logs the router activities.
View 3 Replies
View Related
Dec 31, 2011
I ran autosecure on my 1841 routere and now I cant do ping or traceroutes. What should I do to enable the pings and traceroutes after auto secure is done.
View 1 Replies
View Related
Mar 19, 2012
can you enable dhcp service on a 3560 switch.
View 3 Replies
View Related
Sep 3, 2012
How to Enable IP Accounting in Cre switch 4000 Running cat OS and Cisc ASA 5510 (8.2 )
View 1 Replies
View Related
