Cisco Switching/Routing :: Keep Traffic Local Between Two Sub-nets Using 3750-X
Nov 13, 2011
We have a remote office with a Cisco 3750-X switch with the IP-Services feature set connected via dark-fiber to a 6509-E at the corporate office. We plan on migrating the remote office to a new network (new acquisition) to subnet 10.10.10.0 on VLAN 20 which has an existing subnet of 192.168.100.0 and we would like to run both in parallel using their existing switches (Dell) and the new 3750-X.
I’m curious as to the best way to keep the traffic local between the two subnets using the 3750-X and if necessary put the 192.168.100.0 network on a VLAN. I thought about routing between the two networks via IP routing on the 3750-X but the new workstations default gateway is the 6509-E and existing workstations is a SonicWALL within the remote office. The default gateway for the new workstations can be moved from the 6509-E as a last resort.
View 5 Replies
ADVERTISEMENT
Jun 11, 2013
We created some local account for this switch but we unable to login when the TACACS Server down.
3750 Switch
aaa group server tacacs+ ACS
server x.x.x.x
server x.x.x.x
ip vrf forwarding Mgmt
ip tacacs source-interface GigabitEthernet0
[code]....
View 2 Replies
View Related
May 13, 2012
I need to make some changes on our network. We currently have two sites 150 miles apart we join both by way of fiber and on each side we have Cisco 3750 stack switches, configure trunking for all V lans on one port in site one then through the the long haul fiber to site two with site one using 10.1.1.30 and site two using 10.1.1.40 as their default gateway, with static routing all V lan sub nets to the other sites default gateway life is good.
My question - seeing how we have sites using the same sub net 10.1.1.x to trunk all data to each site through switches; we need to now change the network and add each site to the MPLS network, site one switch 1 IP address 10.1.1.30 going to MPLS router one with FA0/0/0 using IP 10.1.1.31, site two having switch 1 IP address 10.1.1.40 going to MPLS router one with FA0/0/0 using 10.1.1.41. I need to know will this work.
We have the same sub net in each site 10.1.1.x to the MPLS routers then the external router interface connecting each site to local switches, will this cause any problems by using the same local sub net for each site?
View 1 Replies
View Related
Dec 12, 2011
Been dealing with a strange problem for several days now. It started out with a problem that I thought was VTP related but ended up being something else. I setup a span port on a 3750 that I am connected to that was mirroring the trunk connection coming into the switch.
Never saw an VTP traffic come across the connection but doing a sh vtp status indicated the traffic was arriving and getting processed. When I found some debug commands (debug sw-lan vtp), I was also able to see the packets go between switches. Seeing this issue concerns me that there is other traffic that isnt showing up during a span session.
I know that doing a span on a switch, especially using a trunk port as a source, isnt a good idea. Since I didnt have a TAP at time, this was my only choice. I have since borrowed a NetOptics TP-CU3 tap from a good friend and was able to confirm the VTP traffic was going across the trunk connection between switches.
All of my 3750's are running 12.2.55.SE.
View 8 Replies
View Related
Oct 10, 2012
Have a quick question regarding inter-vlan routing on a 3750. Overview of network is ISP --> ASA --> 3750 (acting as my core and default gw). I have 5 vlan interfaces on my 3750, all w/ 192.192.x.x subnets, a 6th w/ 192.168.100.x, and a 7th w/ 192.168.200.x. I have enabled "ip routing" on the switch and can successfully ping from subnet A to subnet B as long as both devices are using the correct DG for their vlan, which is the switch. I have a few ports that are trunked as well that go to ESX hosts which break out the vlans according to the subnet the vm should be attached to. The ASA is set to nat internal traffic for all the vlans.
Now my question: short of applying an ACL to each vlan interface to block traffic from other 192.192.x.x subnets is there a better way to accomplish this? I want my 192.168.10.x subnet to be able to reach all the subnets, but don't want 192.192.10.x to be able to talk to 192.192.20.x for example. I was thinking to create an acl like this:
access-list 120 permit ip 192.192.10.0 0.0.0.255 access-list 120 deny ip 192.192.0.0 0.0.255.255 192.192.10.0 0.0.0.255access-list 120 permit ip any 192.168.100.0 0.0.0.255 192.192.10.0 0.0.0.255
and then applying this to the interface for the appropriate vlan.
View 4 Replies
View Related
Jul 15, 2012
I have 2 new 3750g devices in a small environment. switch1 acts as our collapsed core and has ip routing enabled, and is connected to a ASA 5510. There are 3 HP l2 switches connected to switch1 as well. switch2 is simply a server switch. switch1 and switch2 have a 2port etherchannel between them, and a vlan trunk carrying 4 vlan's. traffic between any 2 hosts on switch2 (same vlan) are slow. (average 300Mbits/sec) If I move one of those hosts to switch1, speeds increase by 3 times. (average 900 Mbits/sec). Additionally, traffic between any 2 hosts on switch1 are quick. testing is done with iperf as well as timing 1gig file transfers.
I don't see any errors or drops anywhere, and there are no other symptoms other than slow transfer beteween hosts on switch2. I just got 2 more of these 3750's to put in a 2nd site that we have, put a quick configuration on them, and have the same result. Other than switch1 having ip routing enabled, the configs are pretty much identical.
View 2 Replies
View Related
Dec 2, 2012
I want to know if there is way to tag traffic with DCSP tags without having to do all the other requirments of QOS setup. All i want to do is just tag traffic at different DCSP values via source and destination IPs. We do not have a need to be priortizing traffic on out internal switches. We just want to tag the traffic so our MPLS provider can distinguish the different types of traffic.
Our environments is primarily 3750s in all offices.
View 6 Replies
View Related
May 21, 2012
we have three separated network segments going to one Cisco 3750 switch all is L2 .. from this switch is 100 mbit uplink.we need to apply some Qos mechanism not to saturate line by traffic from one network.. Configuration from various reason CANNOT be done on switch where 100Mbit line is terminated.. so all must be done on SW1,2,3..Correct me if iam wrond but as switches doesnt see traffic from other network iam affraid only think we can do is limit bandwidth on links going into SW1,2,3 to 33 Mbit.I found commad srr-queue bandwidth limit.But links going to SWs are 1Gbit so if i force bandwidth to 10% (minimum what command allows) its 100 Mbit..If I force speed on those links to 100Mbit and than apply srr-queue bandwidth limit to 30% doest it work.??. Will srr-queue bandwidth limit speed to 30Mbit?? Or srr-queue bandwidth limit is calculated from maxim speed of interface?
View 1 Replies
View Related
Mar 14, 2012
I am trying to mark http packets from a web server with DSCP ef, but when I am doing a traffic capture all http packets have tos 0x0.I am able to mark UDP and ICMP packets originated from this server, but not any TCP traffic.The web server is in VLAN 20This is my config mls qos ip access-list extended MARK-HTTP-ACL permit tcp host 10.10.10.10 eq www. [code]
View 4 Replies
View Related
Jun 18, 2012
We would like to setup a link to our DR site that is separate from our main network traffic. This link will be used by an EMC VNX SAN for replication traffic. The SAN will be plugged into a fiber port on a 3750 switch and going out from the same switch (going in as multimode, going out as single mode) into a patch panel that runs over to the DR site (about a mile away). At the DR site it will go from the fiber panel into another 3750 switch which ends up going back out of that switch into our DR SAN.
I'm wondering what the best way would be to configure the fiber ports to accomplish this. I'm affraid that the replication traffic will find it's way over through another route and congest our main network unless configured appropriately.
View 4 Replies
View Related
Jan 28, 2013
Unable to limit traffic on catalyst 3750 gigabit ports it has fiber modules,
I want to limit traffic 2mb per port
I have tried srr-queue and policier but it is not working and there is no ratelimit command under any interface, Applying policy to output is not supported of the interface
policy-map rate-limit
class class-default
police 2000000 8000 exceed-action drop
int gi1/0/3
service-policy input rate-limit
still when I start download it goes to 10 mbps
View 12 Replies
View Related
Feb 23, 2012
We have 2 switches split across 2 datacentres connected via an interconnect. Over the past couple of days the interconnect provider's Cisco kit has shut down our port (err-disabled) due to a broadcast storm. They had the level set at 1 which I thought was a bit low. They say they tried to set to 2, then 5 but still kept tripping the storm-control feature so they set at 10. They say they've always had it set at 1% (on a 100Mb switch) and so we must be generating more broadcast traffic.
I'm trying to identify where the broadcast traffic is coming from. On our Cisco 3750 I've clear interface counters and when I do a sh run | i broadcasts there are a few ports which have what seems like a high broadcast count. The one port that is especially high and the only one tripping the storm-control feature (I've enabled on all our ports to try to identify where the traffic is coming from) is the port connected to the 100Mb interconnect. I've mirrored that port to another port and connected a server with wireshark so I can capture all the traffic across that port.
What I'm struggling to find is the source of the broadcast traffic.I have a few questions are these broadcasts layer 3 or layer 2 broadcasts. Also in the output below when it says broadcasts received is this inbound to the port i.e. from the connected device or is this a total of inbound and outbound broadcasts.
When I use wireshark and filter the capture on broadcasts (ff:ff:ff:ff:ff:ff) I see only 200-300 compared to the thousands the switch is reporting.If I filter on the broadcast IP address I also don't see the numbers corresponding to what I see in the show interface output.
GigabitEthernet1/0/1 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0014.a93f.7401 (bia 0014.a93f.7401)
Description: Interconnect
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 4/255, rxload 44/255
Encapsulation ARPA, loopback not set
[code].....
also I'm currently doing : monitor session 1 source int g1/0/1 both, and also tried just rx incase I just need to be looking at receive traffic but still nothing is standing out.
View 10 Replies
View Related
Jun 3, 2013
Actually i have a design from my customer who have ( Cisco core switch 3750 (allports fiber ports) which is connected to L2 switches , these switches carry servers and end users .the only routing protocol on the access switches is static route ,
My question how can i route the traffic from the server to the end user , as the the server is not direct connect to the core switch.
View 6 Replies
View Related
Mar 2, 2012
We are using Cisco 3750 switches in our environment as distribution switches.We currently use to police inbound traffic, but we need to find a solution to limit inbound traffic per IP.Something like this “Inbound traffic for each IP can be maximum 1 Mbps” This can be done having, one ACL and one class-map for each IP, but in my situation is not a practical solution, because we have more than 500 IP’s on that site.
Is any way to accomplish this without writing 500 ACLs and 500 class-map?
View 2 Replies
View Related
Aug 6, 2012
I am aware that the 3750 switches are not able to support Netflows, so I have created a SPAN port and spanning traffic from a specific port. I would like to create a seperate VLAN and trunk the traffic from the SPAN port down to the 6509 switch and then capture all the traffic for that VLAN on the 6509.
View 4 Replies
View Related
Feb 21, 2013
I have One switch 3750 and many switch 2960 c.I use one ASA 5510 to reach emote branche site (vpn conexion).I use one router 1841 for internet conexion.Router 1841, ASA and catalyst 2960 are connected on the 3750.Default gateway of all user is ASA IP
I configured Vlan 3750 and it work.Now I need to implement security : permit/block specific traffic between vlan [code] From vlan 72 I cannot have remote access on computer in vlan 34 and I cannot ping computer in vlan 34.
View 1 Replies
View Related
Nov 13, 2011
I am trying to setup a network using Cisco 2960 switches with vlans configured. One vlan will handle video coming from four cameras that are connected to another 2960.
We have four cameras feeeding one port each on a 2960, that 2960 in turn feeds one port on the main 2960 which is the video vlan for that site. From the site it goes back to a Cisco 3750 to be sent over to a Sonicwall firewall. If we connect to the 2960 that the camera are connected to we can see the video, but not on the main site 2960.
View 5 Replies
View Related
Feb 21, 2012
On a router I can use IP Accounting or Netflow to see what kind of traffic is moving over an interface. Are there any tools on a 3750 switch with a routed interface which would tell you who is hogging the bandwidth on that interface?
View 2 Replies
View Related
Jan 27, 2013
I have catalyst 3750 I want to controle traffics on every port I have tried Frame-Relay Traffice shaping and Quality of service but there is no support for these commands in the switch.do we have any way to limit traffic on every port in catalyst 3750 and 2960 switches ?
View 4 Replies
View Related
Mar 13, 2013
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies
View Related
Feb 16, 2012
I have a new MPLS circuit being stood up for my site; it’s going to replace a site to site VPN connection to our "Headquarters." I want to test this without affecting my production networks. Without getting into alot of details, the admin at the remote site is not very cooperative and basically doesn't want to set this up and I don't have access to his switching/routing. He is prepared to do minimal tasks if necessary. Ultimately, I am looking to test the new Vlan, once successful, route the traffic away from the Site to Site VPN connection to the MPLS circuit. Here is what I plan on doing, I need to determine if it is going to work.
LAN in my office uses EIGRP for routing. MPLS (10.1.1.253) uses OSPF (area 0) and BGP. Currently, traffic destined to headquarters (10.10.1.1/24) uses the default route on a CAT3750 pointing to the firewall (ASA5520) (10.1.1.254).Create new VLAN/DHCP scope to use as a test Vlan to test the new MPLS circuit. 10.1.199.0/24Create static routes on 3750 destined for headquarters for L2L VPN traffic pointing to firewall so traffic to headquarters remains on the L2L connection. ip route 10.10.1.1 255.255.255.0 10.1.1.254 (once I share routes with OSPF, routes to Headquarters will be advertised over the MPLS)Create OSPF instance on the 3750 advertising only the new subnet so that the MPLS network knows to route this traffic over the MPLS for return traffic from headquarters. (this is where it is grey as I don’t know OSPF at all) The switch has a L3 interface which the MPLS router uses as its gateway, so there is direct communication.router-ospf 0 network 10.1.199.0 0.0.0.255 area 0 4. On 3750 create a PBR for the new subnet so that it is routed over the MPLS, (imagine test PC is 10.1.199.100), the remaining production subnets will use the static routes and ignore the OSPF routes because of the shorter administrative distance.Will the PBR route win over the static route for that one subnet? Is that all I need in the OSPF configuration? I see some configs that have neighbor statements with costs, authentication types etc..
View 3 Replies
View Related
Jun 30, 2012
Do I need the Universal image to perform stftp on a 3750 or 3750-X?
View 8 Replies
View Related
Apr 16, 2012
I have a Cisco 819G WAN Router with the following specifications:
Router3G#show inventory
NAME: "C819G+7-K9 chassis", DESCR: "C819G+7-K9 chassis"
PID: C819G+7-K9 , VID: V01 , SN: xxxxxxxxxxx
[Code].....
View 4 Replies
View Related
Aug 4, 2011
I am trying to come up with the best way to traffic shape traffic with 3750 Me switches. the traffic will be coming from a 6504 Sup-7203b downstream and going out the wan. Core---L3---->6504--intvlan80--trunkport to--->3750Me---g/1/1/1-trunkport to---MetroE network--->int f0/0.80--branch router. The idea is to use the 3750 to traffic shape the traffic going towards the wan/branch to 500 to match the contracted rate and then to use qos on shaped rate. I tried to apply it to g1/1/1 using port based policies but it did not shape the traffic. I changed everything to IP interfaces and it worked. I need to break up the metroe into different vlans so I can bring branch offices in on different vlans.c
View 3 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
Jan 17, 2012
see the attached diagram to explain the network. I'm trying to do a "port-to-port" layer 2 connection on an ASR that will bi-directionally bridge a physical interface to a sub-interface. I tried using " connect VLAN200 Gig0/1/0 Gig0/0/3.200 interworking ethernet " but I'm not getting traffic through the connection.
I don't think BDI will work because it requires a Layer 3 point. I have to make this Layer 2 switching.
View 5 Replies
View Related
May 21, 2012
We have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
View 11 Replies
View Related
Feb 10, 2008
I am working on getting my CCNP. The first exam I plan to take is the switching test BCMSN 642-812. Using the 4th Edition Self-Study Guide from Froom, Subraniaman, and Frahim.In Ch-4 it talks about End-to-End VLANs and Local VLANs. I read that section 4 or 5 times and still did not understand the difference between them two.I know one spans across the entire network and the other is local. What do they exactly mean by that?
View 15 Replies
View Related
Dec 9, 2011
some of our switches have the switchport mode trunk command configured between the 3750 switches but other 3750 switches connected to our 6509 core switch do not have the switchport mode trunk command to permit Vlans from going across the swtiches instead it has an ip address and says no switchport what is the difference between does two. Is trunking used only for Layer 2 and L3 is used to route interface vlans?
View 2 Replies
View Related
Oct 24, 2012
I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies
View Related
Oct 8, 2012
Is a 3750 sw capable of handling full routing tables and what can you recommend in a small mutihomed BGP router or switch capable of handling full routing tables?
View 2 Replies
View Related
Oct 28, 2012
I have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
