Cisco Switching/Routing :: Multiples VLANs On 3750
Jan 24, 2012
I have a stacked Cisco Catalyst 3750 configuration that currently has one V LAN configured. VLAN 192 - 10.192.0.0/16
The Catalyst has an ip on this range of 10.192.0.1. I would like to configured a few more V LAN's to be able to run some more network ranges through this device. Would it be a case of just adding the V LAN's to the master and then configuring an IP for each V LAN within the inter-v lan routing section? Some V LAN's will require access to each other but not all.
View 8 Replies
ADVERTISEMENT
Feb 18, 2012
Is is correct that vlan's exceeding 128 runs without spanning-tree.?
View 7 Replies
View Related
Jun 19, 2012
I have to put an ACL Firewall in front of a public IP range.There's no routing so I want to do it with a transparent layer 2 Firewall. I found this document which descibes exactly that feature I need: [URL]
It seems to be a feature introduced in IOS 12.3.
My Questions:
1.) is it possible use this transparent firewall feature with the 3750 Switch instead of a "normal" IOS-Based router?
2.) I've seen there is no IOS 12.3 for the 3750 but rather 12.2 (currently installed) or 15.0.1. Is this Feature included in 15.0.1?
If the feature described above is not available, is there any other way to achieve my goal?
View 1 Replies
View Related
Nov 8, 2011
I'm trying to setup a port on a catalyst 3750 so it will pass traffic for 2 vlans. It connects to a (watchguard) firewall which I've configured with a primary IP (for vlan 27) and a secondary IP (for vlan 29).
However I can't seem to find the correct commands to enter on the cisco switch port (I've tried a variety).
FYI the current configuration is...
interface FastEthernet1/0/38
description ## Connection to WG vlan27 and vlan 29 ##
switchport trunk encapsulation dot1q
[Code].....
View 8 Replies
View Related
Feb 13, 2012
Currently we have an Ava ya IP Office switch running on the same network as our PC clients. I would like to seperate the two network into 2 V LAN's.
We have a mixture of Catalyst 3750 switches and some older 3500 models.Where do I start? Should I leave the PC's and servers on the default V LAN and just move the IP handsets?
View 6 Replies
View Related
Jun 27, 2012
I am looking for a way to create different routing policies for vlans on a 3750 table.
My set up is
Clients----------- 3750 -------------- ASA ---------------Servers
|
|
|
Internet Routers
What i am trying to do is on the 3750 to route private networks to my ASA on different subintefaces and all internet to my internet routers . Each VLAN has a different GW for the internet. On some case i have the ASA as a default gateway. ASA default default route is 3750 where i need the internet traffic to be spllited on the proper Boarder router.
View 1 Replies
View Related
Apr 11, 2012
I would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?
View 9 Replies
View Related
Jun 1, 2012
I am trying to configure router on a stick with 2811 and 3750, but I just cannot get it to work - vlans are not getting propagated from 3750 to 2811: 3750:
Code...
View 1 Replies
View Related
Feb 4, 2011
I'm setting up a Cisco 3750 layer 3 switch with several vlans. I thought enabling routing would route between the vlans, but no such luck.What I want is to share the internet access of vlan 100 with the other vlans/ip-nets.How can I do that?
View 2 Replies
View Related
Jun 30, 2012
Do I need the Universal image to perform stftp on a 3750 or 3750-X?
View 8 Replies
View Related
Jul 4, 2012
upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies
View Related
Jan 23, 2013
I have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
View 5 Replies
View Related
Mar 27, 2012
I have purchased these two switches from ebay as a test lab, I plan to connect them up via a gigastack modulecable and enable ip routing on the c3550 and vlans to talk to each other.
I'm very much a procurve person and really need to get into the cisco switching.I will want to trunklacp between the switches - whats the process is setting that up on cisco switches?
View 1 Replies
View Related
Feb 19, 2012
I have a 3560E with 2 vlans that I want to route between. one device with 2 vlans and route between.Interfaces are configured as such:
int g0/11
switchport mode access
switchport access vlan 10
int g0/12
switchport mode access
switchport access vlan 11
[code]...
Laptops on each port with 10.10.10.2 and 10.10.11.2 configured on them. I can ping from 10.10.10.2 to 10.10.11.1, but not to 10.10.11.2.What do I have to configure to be able to get the 2 laptops to talk to each other?
View 9 Replies
View Related
Jan 24, 2013
I am setting up a vm environment for a customer in my lab off site. I have two stacked 3750-x switches, a san, and threes UCS c220 M3S servers for hosts. I am trying to separate the lan traffic, san iscsi traffic, and san management traffic using vlans. The problem is i'm unable to communicate cross vlan with my current config, which I have attached to this post. The only noteworthy things in my conifg is that the ip route 0.0.0.0 0.0.0.0 192.168.83.6 is referring to a switch stack they have on site, that I will connect this stack to using the first two trunk ports on each switch, that I do not have here in the lab. I don't want to cause any confusion in why I have things set a certain way.
View 1 Replies
View Related
Jul 24, 2012
The situation include 2 cisco routers an 2 switch 3550
so we have Router A in Vlan x access ----->Sw1----Trunk----Sw2<------Vlan y Access Router B I 've to enable rip1 on guys A and B ONLY !!! Avoiding any kind of tunnel I though it was all around fallBAck bridging ... but after days of tries ...
View 3 Replies
View Related
Jul 24, 2012
I have tried to test copy tftp: numerous time with no success. I believe the reason it is failing is my laptop to Ethernet port is in vlan 62 and the tftp process operates in a different IP space.I am using gig 7/1 and configuring my laptop nic for x.x.x.254 mask 255.255.255.0. I can ping from laptop to gateway) and I can ping from the switch to my laptop using ping vrf production x.x.x.254. Can you tell me what vlan I need to set my laptop connection in or if there is something else I need to change to make tftp work on vlan62?Does TFTP only work in vlan1 or can it be changed?
View 2 Replies
View Related
Oct 23, 2012
I recently set up a Cisco 881 to cover a small business network. The router is currently set up and working as expected. We recently decided to move to VoIP phones and here is where I'm running into some issues.
First an overview: We run a network with a cable internet WAN connection, this connection is DHCP, however we have a static IP through our ISP. We also have a block of 30 additional IP addresses for one to one mapping as we need them. The new VoIP system is being run over T1 lines throughout the township (we are a municipal organization) and the VoIP system is being run to about 5 buildings in the township.
This brings me to the topic of VLANs. As the phone engineer explained it to me, there is a network set up over the T1 that allows the VoIP equipment to talk to one another and operates all of the VoIP phones on one network. The equipment that is being installed at our building connects to the network over the T1 and "talks" to the other equipment on the network. The engineer wants to create a VLAN and run it on ports fa1 and fa2, with the fa2 port being connected to the actual "MPLS" (their term) that connects to the T1 and into the cloud, and the fa1 port connected to the internal phone switch.
TLDR; The problem is this: When we attempt to set up the VLAN on ports fa1 and fa2, we have no connectivity with the other units in the external VoIP cloud. Pinging while directly connected to the "MPLS" yields successful pings, while pinging from the router with the "MPLS" connected to fa2 yields failures. I'm going to post the running config below, I feel like what we're doing should be working. I asked around about subinterfacing, but others seemed to think this was not necessary.
ROUTER CONFIG
Building configuration...
Current configuration : 4909 bytes
!
! No configuration change since last restart
version 15.1
[Code].....
View 10 Replies
View Related
Dec 12, 2011
I have VLans 20 and 21 set by ISP for Voice and Data respectively.What will happen if I already have VLans 20 and 21 in my Local network?
View 4 Replies
View Related
Sep 7, 2011
I want to know, if it is possible to create multiples BGP AS Numbers on a ASR1K6 Router or ASR9K6 Router.
View 3 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
Feb 10, 2008
I am working on getting my CCNP. The first exam I plan to take is the switching test BCMSN 642-812. Using the 4th Edition Self-Study Guide from Froom, Subraniaman, and Frahim.In Ch-4 it talks about End-to-End VLANs and Local VLANs. I read that section 4 or 5 times and still did not understand the difference between them two.I know one spans across the entire network and the other is local. What do they exactly mean by that?
View 15 Replies
View Related
Jun 18, 2012
I just want create vlans on switch sge2010p
Scenario:
vlan10
ip address 192.168.10.254/24
vlan20
ipaddress 192.168.20.254/24
vlan10 needs internet.
I have a static ip internet which is 200.33.22.11 gateway: 200.33.22.10 I have a router configured working as gateway, It has ip 192.168.2.1.
I have configured two vlans. But when I try to check if vlan has internet, it doesn't work.
View 2 Replies
View Related
Mar 18, 2013
I have the need to filter multicast between vlans as described below. PIM Sparse-Mode is being utilized for this multicast network and changing any Vlan to PIM Dense mode is not an option.
- Vlan 217 and Vlan 4 should not be communicating on mcast with any other vlan, including eachother (each vlan isolated).
-Vlan 64 and Vlan 80 are able to communicate witch each other on mcast but not with any other vlans (isolated vlan group).
-All other vlans can communicate mcast freely.
What I've created thus far is below. It does not appear to be the most elegant solution and would be difficult for the administrators to adjust as new requirements come along. Yes, I will be adding the appropriate link-local multicast addresses so as to not break routing and other dependent technologies.
ip access-list ext ANY_CONN
permit ip any any
ip access-list ext MCAST_INTRA_217
permit ip 224.0.0.0 15.255.255.255 133.106.197.32 255.255.224.0
permit ip 133.106.197.32 255.255.224.0 224.0.0.0 15.255.255.255
ip access-list ext MCAST_ISOLATE
[code]....
View 1 Replies
View Related
Mar 18, 2012
We have the need to create a large number of VLANs on one of our networks. We're talking about 60! These will all terminate on a pair of 6509-E switches (building core). We use MSTP as a standard on our network so I'm going to stick with that so that we can dramatically reduce the number of STP instances needed. However, regarding the SVIs (default gateways) is there any reason why creating 60 of these guys would be considerd a big no-no? Or would you expect the 6509s to deal with them like a boss?
View 4 Replies
View Related
Jun 12, 2012
I have 10 2950 switches on my network that support only 64 vlans on each one. I actualy have requrement to cleate around 100 vlans acros them, can I switch off vtp and create required vlans manualy? I will have more or less following set up:
router
|
2950 - vlan 1,2,3,4,5,6,7,8,9,10
[Code].....
View 12 Replies
View Related
Aug 27, 2012
I need to set up a VLAN. We just bought the SG500x switches and we need to create several VLANs.
So for example:
192.168.1.x --> Vlan 1
192.168.2.x --> Vlan 2
192.168.3.x --> Vlan 3
What I would like to know is how do I come about setting this up and do I have to do something with my DHCP server to allow this to happen?
View 2 Replies
View Related
Mar 4, 2013
I'm unable to pass the required vlans networks to my firewall I have different vlans configured for each floor of the building, All these floors have Nortel switches which are connected to the core switch through fiber link.
I have a Cisco 4507R-E core switch. Config for the core switch below: what else has to be done in order to pass the vlans to my firewalls.
Current configuration : 18527 bytes
hostname HQ_Prim_Core_Swt
boot-start-marker
boot-end-marker
enable secret 5 $1$xj2Z$TmV9chRtQWCuXYMsCtBVW/
enable password 7 13521317135C0729
[code]....
View 5 Replies
View Related
Sep 5, 2012
Is this supported on a 3750X ?? A router has two VRFs and its lan interface is a trunk with 2 VLAN IDs, let say VLAN 10 and VLAN 20. The ip address subnet of these two vlans is the same (therefore , they are in different VRFs)
fa0/1
VLAN 10 = 10.15.4.9 (VRF A)
VLAN 20 = 10.15.4.10 (VRF B)
This router is connected on a 3750X switch. There is a firewall connected to this switch also, which is default gateway for several VLANs including VLAN 10 (10.15.4.1)
The goal is that VRF B ip can talk to 10.15.4.1 and VRF A can talk to 10.15.4.1 but VRF B can't talk to VRF A (10.15.4.9 <-> 10.15.4.10)
FW |--- TRUNK VLANs 1,2,3,4,10 ---------| SWITCH |----- TRUNK VLAN 10,20 -----| ROUTER (vlan 10 = VRF A, vlan 20 = VRF B)
I think this is not supported on the C3750, as my promiscuous port is located on a trunk.
View 1 Replies
View Related
Mar 18, 2012
Im just starting to learn cisco, currently I already have a cisco catalyst 3750 configured for 3 vlans, and now im planning to have another 3750 for redundancy.
View 5 Replies
View Related
Nov 2, 2011
3945 is running c3900e-universalk9-mz.SPA.151-4.M2
3560e is running c3560e-universalk9-mz.150-1.SE
I've got brand new 3945's with onboard 16-port 3560e switches. On the first power up I see that there are several new vlans added that appear to be default vlans..
vlan 2 name fst2
vlan 3 name fst3
vlan 4 name fst4
vlan 5 name fst5
vlan 6 name fst6
vlan 20 name VLAN0020
vlan 21 name VLAN0021
vlan 22 name VLAN0022
vlan 23 name VLAN0023
vlan 99 name VLAN0099
I deleted the vlan.dat and reloaded the switch but these vlans come back. What these vlans are intended for and is there a better way to get rid of them? What does "fst" stand for?
View 4 Replies
View Related
May 9, 2012
Switch: SG500 VLANS: 1 (default) xxx.xxx.0.0/24 network, 150 (device management vlan) xxx.xxx.150.0/24 network I am plugged into port 1. This is a trunk port with VLANs assigned as follows: VLAN 1 (Default) - UntaggedVLAN 150 (dev mgmt) - Tagged Device is plugged into port 2. This is an access port with the following VLAN assigned: VLAN 150 - Untagged Why is it I cannot communicate with the device on port 2?
View 1 Replies
View Related
Apr 9, 2012
Recently purchased 5 SGE2010P 48-port switches to replace older L2 switches. I have 4 switches in single stack and one as a standalone. Both the stack and standalone will connect to at least 1 Dell 2724 switch. Both the stack and the standalone Cisco are in Layer 3 mode.
I have created several VLans on the Cisco switches, and am trying to assign an IP address to the VLan, but cannot seem to figure out the web gui. Each time I try to use Systems > System Management > IP Addressing > IP Interface, then click Add, it simply changes the existing IP of the management interface. So, I'm not sure how to go about assigning an IP Address to an Vlan.
View 15 Replies
View Related
