I have two 800 series routers that I would like to create a IPsec VPN between but one site is using DHCP and I don't think a static IP address is going to be a possibility. Any good documentation? Everything that I've found online with this situation mostly addresses a Cisco at one end and another vendor at the other...
View 4 RepliesI have two Cisco RV220W routers and I would like to realy DHCP from the home office to the remote office accross the IPsec Tunnel. Is this possible and if so how?
I have already gone into the IPv4 LAN (Local Network) settings on the remote router and set the DHCP mode to "DHCP Relay" providing the internal ip address of the home office router as the remote DHCP server.
I am trying to configure DHCP relay through VPN, I read different articles, but I cannot figure it out: The setup is as follows:
Site1:
DHCP server: 192.168.200.21Cisco 877 ADSL router Internal IP: 192.168.200.12External IP: 194.99.99.194
Site2:
Cisco 5505 ASA (behind a ADSL router 192.168.1.1, vpn ports 500 and 4500 forwarded to ASA)Internal IP: 192.168.2.1External IP: 192.168.1.2
There is a working ip sec site to site vpn between site1 and 2. I want the clients on site2 to get an ip address from the dhcp server in site1.
On the Cisco ASA:dhcprelay server 192.168.200.21 outside dhcprelay enable inside set route should be on or off ?
Cryptomaps:permit 192.168.2.0 192.168.200.0 (original crypto)permit 192.168.1.2 192.168.200.21 (added)permit 192.168.2.1 192.168.200.21 (added)
Site1:
On the Cisco 877: Cryptomaps:permit 192.168.200.0 192.168.2.0 (original crypto)permit 192.168.200.21 192.168.1.2 (added)permit 192.168.200.21 192.168.2.1 (added). What NAT entries do I need to use on the ASA and 877 ?
I have two cisco 877 routers one with static ip and the others (3 more routers) with ADSL DHCP using no-ip.com.Currently i'm doing tests with only the static IP router and one DHCP router, I can't seem to get the tunnel up and running, i can connect using Cisco VPN client, but site to site which is the most important one is not workinglI followed the configuration example on this document url...But i have no crypto session output as well as no ipsec or isakmp output using this commands (This is on the Static IP Router) [code] on the dynamic ip Router side i do have output only with the sh crypto ipsec sa command. [code]
View 4 Replies View RelatedI have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View RelatedWe have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies View RelatedThe scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies View RelatedI have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies View Relatedi have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies View Relatedi want configure VPN between backoffice which have ASA5510 firewall with static IP and site which have cisco router 1861 with dynamic IP.
how i can configure the site to site between them?
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies View RelatedI have an ASA 5525 and need to configure site to site ipsec vpn to 3 peers. I currently have an existing /28 public address from my ISP that is used by other services.Is there a way to use this existing ip range to configure IPSEC tunnels to 3 peers ?
View 10 Replies View RelatedI configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?
Our Headquarter (asa 5510) is running a site to site vpn connection with a Branch office (router 2811). All remote users are accesing the internet through the VPN and also accesing headquarter file servers.I want to know if there is a way for some remote users to be able to use the vpn for accesing the file servers but to access the internet through the branch office. The rest of the remote users will be still accessing the internet through VPN.
View 2 Replies View RelatedWe've just deployed a site-to-site VPN using a 5505 ASA on the client's site and a checkpoint Nokia FW on our site. Everything seems to be fine except that the user's connections to their file shares seem to be intermittently dropping. One minute the connection to the shares is there, next thing it's lost. There is no logic to it because no two users are experiencing issues at the same time, as a matter of fact even on the same PC where a user has access to 3 shares on 3 different servers, one could be showing as connected whereas the other two be dropping. [code]
As you can see the Duplex and Speed are set to auto, I've rectified this since then and I'm keeping a close eye on the output errors, and collisions. However, I'm afraid that this did not rectify the issue and the users are still experiencing intermittent connection dropping to their file shares over the VPN!
I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.
I've setup a site to site vpn on an ASA 5510 using ASDM (as I have many times before) and the tunnel appears to be up but I am not able to pass traffic. When I run the packet tracer from my inside network to the remote destination network, it shows that it is blocked by the implicit deny ip any any rule on my inside incoming access list.
View 5 Replies View RelatedGot an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.
Currently the rules are as follows
Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny
[code].....
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.
we have two ASA 5510s one in 8.4(4) and one in 8.2(5) in a site-to-site VPN setup. All internal traffic is working smoothly.Site/Subnet A: 192.160.0.0 - local (8.4(4)) Site/Subnet B: 192.260.0.0 - remote (8.2(5)) VPN Users: 192.160.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible.
Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise.There are also some weird NAT rules that I am not happy with that were created after I upgraded Site A ASA to 8.4
Site A internal: 192.160.x.x External: 55.55.555.201(main)/202(mail)
Site B (over site-to-site) is 192.260.x.x External: 66.66.666.54(all)
I pretty much just have the basic NAT rules for VPN, Email, Internet and the site-to-site.What do I need to add for the VPN to be able to access the site-to-site network?
Here is my NAT config:
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static VPN_Network VPN_Network no-proxy-arp route-lookup
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static DOMAIN_REMOTE DOMAIN_REMOTE no-proxy-arp route-lookup
!
object network DMZ_Network
nat (DMZ,Outside) dynamic interface
object network DOMAIN_LOCAL
[code]....
I setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access.
Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
ASA = 8.2(1)
ASDM = 6.2(1)
Recently I used the wizard to create an IPsec site-to-site connection, which went very smoothly; however, I now noticed that when I connect via Anyconnect 2.5.0217 I cannot get to local and subnatted resources on the network.
I rolled back to saved config file, which was taken before the site-to-site vpn was created, but that did not work as well.What should I check to see why I can no longer get to different subnets after the site-to-site vpn connection.
I am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).
I have a ASA 5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.
Secondly request also they need failover over the ISP link.
how we immplement the same on ASA 5510.
Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.
Currently the rules are as follows
Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny
[code]....
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.
I have a ASA 5510 at our corporate HQ that has one site to site VPN. I need to add 6 additional site to site VPN's to this ASA for our remote branches. How can I add them without affecting the existing site to site VPN? The 6 site to site VPN's will all have the same settings however these settings are different from the existing site to site that I already have set up. How can I set it up so the 6 additional VPN's use their own crypto map and all use the same settings?
View 1 Replies View RelatedWe recently purchased an SRP527W router because of its capability to configure site-site VPN tunnels. The configuration of IKE and IPSEC is working and the tunnel comes up but the problem is that the router is passing our internal IP addresses through the tunnel. The remote end we are connecting to requires us to hide all traffic behind one IP address which would ideally be our external static IP address from our ISP.
View 1 Replies View RelatedWith à customer we have à site to site VPN connection. In this tunnel there is one subnet routed with a 3des-sha encryption / hash. Now the want to add a new subnet in this tunnel, but with a AES-128 / MD5 encryption / hash. Is it correct if we make a new crypto map with a higher seq. number?
View 5 Replies View RelatedWe have a client that has a Cisco 1801W Firewall that is setup as a site to site VPN terminating to a Cisco ASA 5505. The tunnel is up and established, I can ping from both sides of the tunnel.
The problem is the clients behind the Cisco ASA (192.168.2.x) cannot reach certain ports behind the Router (192.168.1.x). The main thing we're trying to do is browse via UNC path (ex: \192.168.1.120 from a 192.168.2.x machine).
I got 3389 working after I changed the - ip nat inside source static tcp 192.168.1.120 3389 y.y.x.x 3389 route-map DM_RMAP_1 extendable Modified the command to include the public IP instead of interface FastEthernet0
I believe it has something to do with the way NAT and route-maps are setup currently but I'm not familar enough with them to make the changes. I worked with Cisco to ensure the VPN tunnel was fine and it's something security related on the Router.
Here is the configuration (removed a few lines not necessary. y.y.x.x = WAN IP of Router x.x.y.y = WAN IP of ASA).
Building configuration...
Current configuration : 23648 bytes
!
version 12.4
no service pad
[Code].....
I have some challenges with a VPN config I recently setup for a client.I have at the HO the following:
- 1800 router
- Avaya phones and Gateway
- 1MB radio internet access
At the BO(branch office), i have:
- 871 Router
- Avaya phones
- 256k internet bandwidth
The only reason we setup the VPN in the first place was for the phones at the BO to be able to connect to the gateway at the HO and also able to make calls and receive calls as if the phones were at the HO.The phones at the BO successfully register to the HO, but are unable to recieve calls and dial out. Everytime I try to make a call, the phone displays a "connecting..." message. [code]
I'm getting a Cisco 1841 router to do a site-to-site VPN. I'd like to know what's the minimum IOS software feature set required for site-to-site VPN?
View 3 Replies View Related