Cisco VPN :: ASA 8.0 / VPN Remote-access Without Encryption And Hashing?
May 29, 2012
I am trying to setup a remote-access vpn (client device is an iphone or PC) on asa 8.0 with a transform-set without encryption and without hashing ( crypto ipsec transform-set noenc esp-null esp-none ). In this scenario, it does not work and all gives me "phase 2 mismatch" ...below is the debug of isakmp and ipsec.
i tried to change the transform set by using hashing without encryption (crypto ipsec transform-set myset esp-null esp-sha-hmac). it worked on the PC but not the iphone. my target is for the iphone to work.
ciscoasa# sh cryciscoasa# sh crypto isa sa
There are no isakmp sasciscoasa# ter monciscoasa# May 29 23:33:44 [IKEv1]: IP = 91.232.100.3, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 741May 29 23:33:44 [IKEv1 DEBUG]: IP = 91.232.100.3, processing SA payloadMay 29 23:33:44 [IKEv1 DEBUG]: IP = 91.232.100.3, processing ke payloadMay 29 23:33:44 [IKEv1 DEBUG]: IP = 91.232.100.3, processing ISA_KE payloadMay 29 23:33:44 [IKEv1 DEBUG]: IP = 91.232.100.3, processing nonce payloadMay 29 23:33:44 [IKEv1 DEBUG]: IP = 91.232.100.3, processing ID payloadMay 29 23:33:44 [IKEv1
[code]....
View 3 Replies
ADVERTISEMENT
Dec 10, 2012
how to perform Linear Hashing in databases on given values?
View 2 Replies
View Related
Oct 18, 2011
I am support one client for, whom falls under Security scans mandatory for new implementation of ASA 5520 device. The client uses Nessus Scan and the test results are attached.The Nessus scanner hit on 1 Medium vulnerabilities.
View 2 Replies
View Related
May 7, 2012
I have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 Replies
View Related
Aug 16, 2012
Im currently connected to a remote acess vpn setup using the vpn client and am unable to get anywhere around my network, this normalyl works fine The only difference i can see is that the are multiple virtualaccess interfaces pointing to my public ip address, which im presuming is causing routing issues How can i clear these unsed virtual access lines and how can i make it forget them automatically after disconnects?
View 5 Replies
View Related
May 17, 2011
We have an ASA5510 and a few days ago we were unable to access some segments from remote access VPN, the problem was not the config. A few hours later the problem was resolved on its own and I suspect we have an IOS bug. This has happened a few times in the past and its becoming an issue. How can this be confirmed and which IOS should we upgrade to? Prefer not 8.3 given the syntax difference
View 1 Replies
View Related
Nov 1, 2011
Based on my diagram, my computer A (192.168.100.11) can ping and access my computer B (192.168.10.14). But, when i'm home and i use remote access vpn (192.168.200.x) in cisco asa 5520 to connect to my computer A is okay. But, when i try to ping my computer B is not okay. I already do the exemption for 192.168.100.x and 192.168.10.x in nat rules for inside interface (192.168.100.2) ...
Should i put routing from outside 1.1.1.2 to 192.168.10.x by using 192.168.100.1 as a gateway?
View 1 Replies
View Related
Jun 10, 2012
I am looking to connect to a remote site that is connected within a larger corporate network. Curently I can connect to the corporate network via VPN, we have a single address on thet network in to the second port on a PC. I can then remote desktop this machine to access our network.Ideally I would VPN on to our network directly then I can communicate with devices directly, but I need to be on the corporate net
View 2 Replies
View Related
Jun 14, 2011
I have three servers at home called Matrix, Skynet and Hal.Currently when I RDP to remote.domain.net I get to my Matrix Server. However I would like the option to have a matrix.domain.net, skynet.domain.net and hal.domain.net that I can RDP to remotely. Is this possible. I was thinking by using different ports on my Router to route the request through to the right server. And if that way would I need to put the port into the name when connecting. ie skynet.domain.net:1234?
View 3 Replies
View Related
Nov 7, 2012
I would like to know if there is a possibility to create 2 Remote access VPNs for 2 ASA situated in different sites and using only one PCF file.Is set up a tunnel between the 2 ASA the only way to reach the 2 destinations with the same PCF file?
View 6 Replies
View Related
May 25, 2011
I have a remove access vpn configured on my ASA 5510 which works fine, VPN pool easily allocates IP to all remote used , but they have few network drivers shared on their machines & most of them are linked using the computer name rather than the IP which normally doesnt work as VPN pool doesnt provides the DNS IP to the remote clients . Is it possible to allocate DNS IP with the VPN IP ?
View 1 Replies
View Related
Feb 14, 2013
I have created Remote access vpn on ASA 5505 (ver 8.2(5) with base license). When I connect from one machine, I can ping the internal network. But when I connect from another machine, cant.I have only decrypts on the ASA side, without encrypts. I was debugging ICMP packets with the capture feature, and saw that echo-reply packets are returning toward the outside interface, but aren't passing through it.
capture test access-list test interface outside
1: 08:54:44.298980 802.1Q vlan#1 P0 x.x.x.x > y.y.y.y: icmp: echo reply
Where x.x.x.x is LAN and y.y.y.y is the VPN client ip. The nat is ok, access lists are ok, but the packets dont pass through.I tried creating new VPN profile but the same problem, it seems that only one remote client can be active even base license allows more than 1 client.
View 2 Replies
View Related
Dec 11, 2012
how to configure simple VPN access for a user to login to the corporate network and access the resource and get emails I do not want to use CA certificate for authentication instead a very simple method is what i plan to start up with the configuration step so i can test this out.
View 4 Replies
View Related
Dec 10, 2012
I'm configuring remote access on my cisco 881. Protocol PPTP was chosen.I've configured PPTP VPN access on my router, but there's an issue with accessing my LAN. I can access my Internet connection and open web sites, but I'm not able to access my local resources.I can only Ping my router's interfaces (192.168.2.10, 79.104.14.62) and Internet resources. For example, I can not ping switch, directly attached to the router, with address of 192.168.2.2 and other hosts on LAN.
View 1 Replies
View Related
Aug 19, 2012
We plan to use ACS 5.3 for remote vpn user authorization. We have found a document on to how to do this, but they use ASA 8.3.we would like to know if it is supported on ASA 8.2 or do we need to upgrade the ASA IOS.
View 2 Replies
View Related
Jul 22, 2012
I have a SG 300 switch and configured it with public IP address.I can access it from anywhere within my network but not from outside my network as I'am not able to add the gateway and DNS address as there are are no fields to add them in the IP configuration menu in L3 mode.
View 1 Replies
View Related
Jun 19, 2011
Got a single asa 5505 configured in the office. we have 3 site to site vpn connections from this device, which all work from within the office.Ive not setup my pc to connect from home to the asa via the ciso client.
i can connect to all LAN servers on the local subnet, however i cannot connect through the ASA to any of my site to site vpn's.
if i do an ipconfig on my home pc i can see my local ip, mask & gw, and i can see my assigned remote access ip & mask but no gw.
I cannot ping any remote site to site pc's by IP or name.
View 6 Replies
View Related
Sep 20, 2011
I have access to my enterprise network through Cisco VPN (software) client and it goes through remote-access ipsec vpn setup on an ASA 5510. Everything works fine.
But now users that connect to the enterprise network have in addition need to access remote sites networks that are connected through the site-to-site VPN tunnels: IPSec tunnels between mentioned ASA5510 and remote ASA5510s and ASA5505s in branch offices.
there is NAT exemption rule that exempts networks 10.1.10.0/24, 10.1.20.0/24, 10.1.30.0/24.All traffic from local network 10.1.1.0/24 have full ip connectivity with all the networks in branch offices. The PROBLEM is that remote vpn clients can reach only local network 10.1.1.0/24, but not the remote networks.
The ASAs in remote branch offices has set up NAT exemption towards both local network 10.1.1.0/24 and remote access clients network 10.0.5.0/28, but as I said, it doesn't go.
View 2 Replies
View Related
Sep 13, 2011
Remote access VPN. Its configured on a Cisco PIX525 running ver 6.3(5) (old I know!) and I am running Cisco VPN client ver 5.06.0160 on the client end. Ok so here's the thing. The client connects ok, and it gets an IP address no problem. But I cannot ping anything on the remote LAN. So the client is coming across the internet, the VPN adapter has a 192.168.1.1 address assigned by the PIX and I am trying to ping the 192.168.0.4 address assigned to a switch on the inside of the firewall but with no joy. [code]
View 1 Replies
View Related
Nov 26, 2012
I have a remote access VPN to our office network 10.42.10.0. however I have some web services that are located in a production network 10.42.1.0 that users in the office network need to access.This is obviously no problem when using remote desktop to an office PC but when users with laptops remote in and try to access the website on the production network it does not work.
Is there any way for the tunnel also to also allow traffic to the production network for the remote hosts?
View 8 Replies
View Related
Dec 10, 2012
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
[code]....
View 9 Replies
View Related
Apr 24, 2012
We have a ASA 5505 in our enviroment. We already configures two site 2 site VPN to our branch offices. Now we are planning to configure remote access VPN. So what should be consider when configuring the remote access VPN in ASA which already having site to site VPN?
View 9 Replies
View Related
Mar 20, 2011
I like to create a remote access VPN in our company. But it already has a site to site VPN.
1. Can we implement it with existing ASA?
2. How many users can be logged in at a time?
3. Is the currently available bandwidth sufficient at a high traffic ? Current bandwidth is 2Mbps (Expect maximum 30 users at a time)
4. How can we make authentication using active directory?
5. Can we use default VPN client in windows with ASA?
6. How can we monitor user’s activity while logging in using VPN?
View 7 Replies
View Related
Mar 24, 2013
I have a problem with a Remote Access VPN on a ASA 5510 8.6.2 .I have created a IPSEC Remote Access VPN through the wizard this is pretty much a base install on the ASA without much configuration.
I can connect to the ASA via the Remote Access client and get TX just no RX therefore i cannot access any of the LAN resources. [code]
View 13 Replies
View Related
Feb 23, 2011
I am looking at purchasing a new Server, but one of my main requirements is to have remote access for users. What are the requirements for good remoting services and which server OS would provide at least adequate remoting services. That is being remoting that provides concurrent use, speed where things do not load slowly and perhaps ease of use, so users can access files.
View 5 Replies
View Related
Feb 28, 2012
We currently use Cisco VPN Client but are looking for an alternative that doesn't lock the user from connecting to the outside internet. I know internet access would make a remote connection more risky but we have situations where the trade-off is justified.
View 2 Replies
View Related
Oct 3, 2011
I have Cisco ASA 5505 and i want to create vpn remote access ...l
so i created and connected to the vpn ...my problem is to reach my Local connection of 192.168.1.0 /24 i put the WAN Connection in the FA0/0 and put my LOCAL AREA CONNECITON into FA0/1 .. so how i can route or translate my connection , and using cisco ASDM 6.1 in GUI ,,,
View 1 Replies
View Related
Jan 22, 2011
I have A setup in different location with the the ASA Firewall with VPN enabled and a Print server. on Network B i have a server with 2008 installed and its my NAT server, DNS and File server.Now the Client on Netwrok B wants to access the Server in Network A Remotely through VPN they could connect to but cannot user Remote Desktop either its Ip translation issue or i dont know.
View 2 Replies
View Related
Oct 3, 2012
I am configuring IPSec Remote Access VPN on a ASA 5505. There are one external interface and one internal interface configured on the device. Internal interface connected to subnet 192.168.1.0/24.en VPN client get connected, I would like to assign the IP from some subnet(for example 192.168.2.0/24) other than the current internel subnet (192.168.1.0/24), but the VPN client can still access to 192.168.1.0/24. Is there a way to do this?
View 2 Replies
View Related
Jul 28, 2011
I have a ASA 5505.|I configured it for remote access VPN from cisco VPN client.the ASA receives a public ip address on outside interface via PPPoE.I can connect to public ip of outside interface and address 10.1.1.2 is assigned to my Cisco vpn client.the problem is that I Cannot ping or reach ASA internal IP address 172.16.29.1 in any way when I am in VPN from outside,while I Can ping other hosts on 172.16.29.0/24 when connected in VPN.this is a problem brcause when I am connected in VPN to ASA I Cannot configure it..Then I Wanted to ask if it is possible a configuration which gives addresses from network 172.16.29.0/24 (the same as inside network) to VPN clients instead of another network (10.1.1.0/24) [code]
View 1 Replies
View Related
Jan 31, 2012
Ive used an old 2500 in the past with multiple serial connections to achieve console connections to all my devices in remote offices. What to use now a days? I dont want to put in an old 2500, i would rather use something more modern. Ive seen a lot of devices out there.
View 1 Replies
View Related
Oct 20, 2012
is it possible to restrict the Remote Access VPN to ASA based on the Source Public IP , if so how ?
here I am not talking about the VPN-Filter under group-policy . I Want to restrict the access from specified source IP ( Public IP)
View 1 Replies
View Related
Dec 26, 2012
i installed Prime LMS 4.2 on Vmware ESXİ 5.0 and then in console screen i create hostname,IP,DNS etc correctly.Then, in LMS 4.2 console screen and another client Win7 PC can ping each other however i cant reach LMS 4.2 via web browser remote client PC.
View 3 Replies
View Related
