i installed Prime LMS 4.2 on Vmware ESXİ 5.0 and then in console screen i create hostname,IP,DNS etc correctly.Then, in LMS 4.2 console screen and another client Win7 PC can ping each other however i cant reach LMS 4.2 via web browser remote client PC.
View 3 RepliesI'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies View RelatedI installed ACS 5.3 on a VM machine for evaluation. The install went fine as I used the recommended settings in the install guide. All the services are up and running when I issue the "show application status acs" command. I am trying to access the web page via http://192.168.1.199:2002 and it just times out. I can ping the server and the server can ping my machine.
View 2 Replies View Related I have a new WLC 5500 series which i upgraded to a newer version. We got brand new AP's 1242 from Cisco. My ex-colleague had said that we can pre-image the AP's using the controller, so the new AP's get the image directly from the Controllers.
I have the following devices with me for this: A WLC 5500, 1242 AP ( 12 No.'s) and a 2960 switch. I tried to create dhcp pool in wlc so the ap get the ip and gets the image . However, i cant see the ap appearing in wireless tab.
The WLC & AP will be connected to this same switch.
What configuration needs to be done on the WLC & the Switch so that the 1242 AP's when connected physically to the ports on the switch will get the image from the WLC.
download an autonomous image for Cisco Access point 1242 ?
View 1 Replies View RelatedI have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is 7.0.116.0 (default) 7.0.98.218 (active) so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its 7.0.116.0 (default)(active) 7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting.
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedI'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
I have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 Replies View RelatedIm currently connected to a remote acess vpn setup using the vpn client and am unable to get anywhere around my network, this normalyl works fine The only difference i can see is that the are multiple virtualaccess interfaces pointing to my public ip address, which im presuming is causing routing issues How can i clear these unsed virtual access lines and how can i make it forget them automatically after disconnects?
View 5 Replies View RelatedWe have an ASA5510 and a few days ago we were unable to access some segments from remote access VPN, the problem was not the config. A few hours later the problem was resolved on its own and I suspect we have an IOS bug. This has happened a few times in the past and its becoming an issue. How can this be confirmed and which IOS should we upgrade to? Prefer not 8.3 given the syntax difference
View 1 Replies View RelatedBased on my diagram, my computer A (192.168.100.11) can ping and access my computer B (192.168.10.14). But, when i'm home and i use remote access vpn (192.168.200.x) in cisco asa 5520 to connect to my computer A is okay. But, when i try to ping my computer B is not okay. I already do the exemption for 192.168.100.x and 192.168.10.x in nat rules for inside interface (192.168.100.2) ...
Should i put routing from outside 1.1.1.2 to 192.168.10.x by using 192.168.100.1 as a gateway?
I am looking to connect to a remote site that is connected within a larger corporate network. Curently I can connect to the corporate network via VPN, we have a single address on thet network in to the second port on a PC. I can then remote desktop this machine to access our network.Ideally I would VPN on to our network directly then I can communicate with devices directly, but I need to be on the corporate net
View 2 Replies View RelatedI have three servers at home called Matrix, Skynet and Hal.Currently when I RDP to remote.domain.net I get to my Matrix Server. However I would like the option to have a matrix.domain.net, skynet.domain.net and hal.domain.net that I can RDP to remotely. Is this possible. I was thinking by using different ports on my Router to route the request through to the right server. And if that way would I need to put the port into the name when connecting. ie skynet.domain.net:1234?
View 3 Replies View RelatedI would like to know if there is a possibility to create 2 Remote access VPNs for 2 ASA situated in different sites and using only one PCF file.Is set up a tunnel between the 2 ASA the only way to reach the 2 destinations with the same PCF file?
View 6 Replies View RelatedI have a remove access vpn configured on my ASA 5510 which works fine, VPN pool easily allocates IP to all remote used , but they have few network drivers shared on their machines & most of them are linked using the computer name rather than the IP which normally doesnt work as VPN pool doesnt provides the DNS IP to the remote clients . Is it possible to allocate DNS IP with the VPN IP ?
View 1 Replies View RelatedI have created Remote access vpn on ASA 5505 (ver 8.2(5) with base license). When I connect from one machine, I can ping the internal network. But when I connect from another machine, cant.I have only decrypts on the ASA side, without encrypts. I was debugging ICMP packets with the capture feature, and saw that echo-reply packets are returning toward the outside interface, but aren't passing through it.
capture test access-list test interface outside
1: 08:54:44.298980 802.1Q vlan#1 P0 x.x.x.x > y.y.y.y: icmp: echo reply
Where x.x.x.x is LAN and y.y.y.y is the VPN client ip. The nat is ok, access lists are ok, but the packets dont pass through.I tried creating new VPN profile but the same problem, it seems that only one remote client can be active even base license allows more than 1 client.
how to configure simple VPN access for a user to login to the corporate network and access the resource and get emails I do not want to use CA certificate for authentication instead a very simple method is what i plan to start up with the configuration step so i can test this out.
View 4 Replies View RelatedI'm configuring remote access on my cisco 881. Protocol PPTP was chosen.I've configured PPTP VPN access on my router, but there's an issue with accessing my LAN. I can access my Internet connection and open web sites, but I'm not able to access my local resources.I can only Ping my router's interfaces (192.168.2.10, 79.104.14.62) and Internet resources. For example, I can not ping switch, directly attached to the router, with address of 192.168.2.2 and other hosts on LAN.
View 1 Replies View RelatedWe plan to use ACS 5.3 for remote vpn user authorization. We have found a document on to how to do this, but they use ASA 8.3.we would like to know if it is supported on ASA 8.2 or do we need to upgrade the ASA IOS.
View 2 Replies View RelatedI have a SG 300 switch and configured it with public IP address.I can access it from anywhere within my network but not from outside my network as I'am not able to add the gateway and DNS address as there are are no fields to add them in the IP configuration menu in L3 mode.
View 1 Replies View RelatedGot a single asa 5505 configured in the office. we have 3 site to site vpn connections from this device, which all work from within the office.Ive not setup my pc to connect from home to the asa via the ciso client.
i can connect to all LAN servers on the local subnet, however i cannot connect through the ASA to any of my site to site vpn's.
if i do an ipconfig on my home pc i can see my local ip, mask & gw, and i can see my assigned remote access ip & mask but no gw.
I cannot ping any remote site to site pc's by IP or name.
I have access to my enterprise network through Cisco VPN (software) client and it goes through remote-access ipsec vpn setup on an ASA 5510. Everything works fine.
But now users that connect to the enterprise network have in addition need to access remote sites networks that are connected through the site-to-site VPN tunnels: IPSec tunnels between mentioned ASA5510 and remote ASA5510s and ASA5505s in branch offices.
there is NAT exemption rule that exempts networks 10.1.10.0/24, 10.1.20.0/24, 10.1.30.0/24.All traffic from local network 10.1.1.0/24 have full ip connectivity with all the networks in branch offices. The PROBLEM is that remote vpn clients can reach only local network 10.1.1.0/24, but not the remote networks.
The ASAs in remote branch offices has set up NAT exemption towards both local network 10.1.1.0/24 and remote access clients network 10.0.5.0/28, but as I said, it doesn't go.
Remote access VPN. Its configured on a Cisco PIX525 running ver 6.3(5) (old I know!) and I am running Cisco VPN client ver 5.06.0160 on the client end. Ok so here's the thing. The client connects ok, and it gets an IP address no problem. But I cannot ping anything on the remote LAN. So the client is coming across the internet, the VPN adapter has a 192.168.1.1 address assigned by the PIX and I am trying to ping the 192.168.0.4 address assigned to a switch on the inside of the firewall but with no joy. [code]
View 1 Replies View RelatedI have a remote access VPN to our office network 10.42.10.0. however I have some web services that are located in a production network 10.42.1.0 that users in the office network need to access.This is obviously no problem when using remote desktop to an office PC but when users with laptops remote in and try to access the website on the production network it does not work.
Is there any way for the tunnel also to also allow traffic to the production network for the remote hosts?
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
[code]....
We have a ASA 5505 in our enviroment. We already configures two site 2 site VPN to our branch offices. Now we are planning to configure remote access VPN. So what should be consider when configuring the remote access VPN in ASA which already having site to site VPN?
View 9 Replies View RelatedI like to create a remote access VPN in our company. But it already has a site to site VPN.
1. Can we implement it with existing ASA?
2. How many users can be logged in at a time?
3. Is the currently available bandwidth sufficient at a high traffic ? Current bandwidth is 2Mbps (Expect maximum 30 users at a time)
4. How can we make authentication using active directory?
5. Can we use default VPN client in windows with ASA?
6. How can we monitor user’s activity while logging in using VPN?
I have a problem with a Remote Access VPN on a ASA 5510 8.6.2 .I have created a IPSEC Remote Access VPN through the wizard this is pretty much a base install on the ASA without much configuration.
I can connect to the ASA via the Remote Access client and get TX just no RX therefore i cannot access any of the LAN resources. [code]
I am looking at purchasing a new Server, but one of my main requirements is to have remote access for users. What are the requirements for good remoting services and which server OS would provide at least adequate remoting services. That is being remoting that provides concurrent use, speed where things do not load slowly and perhaps ease of use, so users can access files.
View 5 Replies View RelatedWe currently use Cisco VPN Client but are looking for an alternative that doesn't lock the user from connecting to the outside internet. I know internet access would make a remote connection more risky but we have situations where the trade-off is justified.
View 2 Replies View RelatedI have Cisco ASA 5505 and i want to create vpn remote access ...l
so i created and connected to the vpn ...my problem is to reach my Local connection of 192.168.1.0 /24 i put the WAN Connection in the FA0/0 and put my LOCAL AREA CONNECITON into FA0/1 .. so how i can route or translate my connection , and using cisco ASDM 6.1 in GUI ,,,
I have A setup in different location with the the ASA Firewall with VPN enabled and a Print server. on Network B i have a server with 2008 installed and its my NAT server, DNS and File server.Now the Client on Netwrok B wants to access the Server in Network A Remotely through VPN they could connect to but cannot user Remote Desktop either its Ip translation issue or i dont know.
View 2 Replies View Related