I have a SG 300 switch and configured it with public IP address.I can access it from anywhere within my network but not from outside my network as I'am not able to add the gateway and DNS address as there are are no fields to add them in the IP configuration menu in L3 mode.
View 1 Replieswe just bought a Cisco SG200-18 to replace our Linksys DLM2008 switches. Now we face a problem with remote desktop between our Win7x64 boxes.
Remote access is abysmally slow, but file transfer speeds seem to be normal. All ports are on Gigabit setting, jumbo frames disabled. The switch on the latest firmware.
how can I remote in to my router and I need to get past my router to my pc desktop
View 2 Replies View RelatedI am trying to connect to my office PCs via VPN and/or RDP. The office uses Qwest DSL and has a dynamic IP address. I use DynDNS.org to keep the DNS updated with the WAN address of the router. However, any attempt to access the network fails. I have tried remote management access (I enabled it on the router) but that fails. I forwarded RDP ports on the router to one of the PCs but can't connect to it. I also set up a VPN server but cannot connect to it either. Something tells me that all requests to myoffice.homeip.net are not getting to my modem/router. I have even tried the IP associated with the name (Yes, I did check that it is correct!) but nothing works there either.
View 1 Replies View RelatedI have a Cisco 678 connected to my ISP (Qwest) using DHCP. This is connected to a Linksys WRT54g router. I also have a home server running for remote access to some files and media streaming. I just installed security cameras that I wish to monitor remotely via the internet.I can access my home files over the internet with no issue. However I am unable to access my cameras using the internet. Looking at my router incoming log, I see my request arriving, but I never get to the DVR attached to the camereas for remote viewing.I enabled bridging on the Cisco 678 but this did not solve the issue.
View 1 Replies View RelatedI have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 Replies View RelatedIm currently connected to a remote acess vpn setup using the vpn client and am unable to get anywhere around my network, this normalyl works fine The only difference i can see is that the are multiple virtualaccess interfaces pointing to my public ip address, which im presuming is causing routing issues How can i clear these unsed virtual access lines and how can i make it forget them automatically after disconnects?
View 5 Replies View RelatedWe have an ASA5510 and a few days ago we were unable to access some segments from remote access VPN, the problem was not the config. A few hours later the problem was resolved on its own and I suspect we have an IOS bug. This has happened a few times in the past and its becoming an issue. How can this be confirmed and which IOS should we upgrade to? Prefer not 8.3 given the syntax difference
View 1 Replies View RelatedI've just gotten a SG200-08 (SLM2008T-EU), which I would like to monitor remotely from Cacti using SNMP. It seems however, that this switch has no SNMP support - is this correct? Does this mean that there is no way to monitor traffic over the switch's ports short of making a script access the web UI?
View 1 Replies View RelatedI am planning to implement RMON remote monitoring in my switch will it any huge effect on CPU utlization .Whether it is resource specific .
I am planning to monitor bandwidth utilization of all the ports in my lan using RMON . Is there any alternative o monitor bandwidth utilization ?I am using LMS 4.2
Based on my diagram, my computer A (192.168.100.11) can ping and access my computer B (192.168.10.14). But, when i'm home and i use remote access vpn (192.168.200.x) in cisco asa 5520 to connect to my computer A is okay. But, when i try to ping my computer B is not okay. I already do the exemption for 192.168.100.x and 192.168.10.x in nat rules for inside interface (192.168.100.2) ...
Should i put routing from outside 1.1.1.2 to 192.168.10.x by using 192.168.100.1 as a gateway?
Someone hacked into my computer through my Netgear router. They took over as Administrator and setup a Atheros (sp) driver. They pretty much have total control over my computer. How can I rid myself of this hack and protect nyself in the future?
View 5 Replies View Relatedi have a slow internet but my friend who live canada have high speed internet can use his internet . i do not want use his remote his computer but internet
View 5 Replies View RelatedI have two locations in the same city and I want to connect them together so I can share files and printers. Each of the LANs has a router and is a simple workgroup. LAN A uses 192.168.1.1 255.255.255.0; LAN B is 192.168.2.1 255.255.255.0. What is the best way to connect these two networks together so I can share printers on both sides? Should I replace the network routers, they are older and definitely could use an upgrade
View 3 Replies View RelatedMy boss is asking me to write a batch file or use a utility to monitor the uptime of 16 different ISP accounts that we use across several stores. Most stores have several ISP accounts setup as failover, so they're not always active on our network but the ISP should still be up. He would like this to run from one of our servers. He is suggesting the 'gateway' for the ISP however I am not sure how to find this IP. The tracert utility returns IP addresses which are different than the gateway address in our router settings so I am wary to use those IPs.Which IPs would I ping to monitor the uptime and where would be the best place to find them?
View 2 Replies View Relatedi provide 192.168.1.201 and port No.8150 in CP Plus DVR . I am able to login through Local system via IE with [URL] after pressing enter key Login window appears. I will type User ID as Admin and password 888888. now i am able to enter DVR and view all cameras. no problemin Beetal ADSL router ( ISP Router) i configured port forwarding as followsIP address 192.168.1.201 and Port No. 8150 both internal & external.Now i got internet IP address through MY IP Address.the IP address is 59.92.67.72 ISPs IP address for my Borad Band.through another internet with different different ISPI open IE and type [URL] got same loging window as in LANagain I enter User Id as Admin and password 888888but shows login failed Message through internet I got the same login window when i tried through LAN, but I am to unable login with a message login failed
View 1 Replies View RelatedIf switches on a network doesn't support remote port mirroring and only local port mirroring, What are the options to still capture all the traffic from all switches on 1 single core switch?
View 1 Replies View RelatedI am trying to Port Forward HTTP: 80, but my Router wont let me and it keep giving me this error message Status: Port Range Overlap with Remote Management.I have a NETGEAR CG814GCMR Router, I need to add that port for setting up a Game private server online, but my router wont let me, how to fix it?
View 12 Replies View RelatedI just picked up a pair of 18-port SG200s, and I'm trying to figure out of there's some secret trick to getting CLI access to them? I've upgraded to the latest version of firmware (1.2.7.76) hoping that may work, but no luck.I can tell the guts to support a CLI are there, because writing the config out to a TFTP server shows identical an identical config style to the SG500 I have here.Is there some way to enable it?
View 5 Replies View RelatedI'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies View RelatedI am looking to connect to a remote site that is connected within a larger corporate network. Curently I can connect to the corporate network via VPN, we have a single address on thet network in to the second port on a PC. I can then remote desktop this machine to access our network.Ideally I would VPN on to our network directly then I can communicate with devices directly, but I need to be on the corporate net
View 2 Replies View RelatedI have three servers at home called Matrix, Skynet and Hal.Currently when I RDP to remote.domain.net I get to my Matrix Server. However I would like the option to have a matrix.domain.net, skynet.domain.net and hal.domain.net that I can RDP to remotely. Is this possible. I was thinking by using different ports on my Router to route the request through to the right server. And if that way would I need to put the port into the name when connecting. ie skynet.domain.net:1234?
View 3 Replies View RelatedI would like to know if there is a possibility to create 2 Remote access VPNs for 2 ASA situated in different sites and using only one PCF file.Is set up a tunnel between the 2 ASA the only way to reach the 2 destinations with the same PCF file?
View 6 Replies View RelatedI have a remove access vpn configured on my ASA 5510 which works fine, VPN pool easily allocates IP to all remote used , but they have few network drivers shared on their machines & most of them are linked using the computer name rather than the IP which normally doesnt work as VPN pool doesnt provides the DNS IP to the remote clients . Is it possible to allocate DNS IP with the VPN IP ?
View 1 Replies View RelatedI have created Remote access vpn on ASA 5505 (ver 8.2(5) with base license). When I connect from one machine, I can ping the internal network. But when I connect from another machine, cant.I have only decrypts on the ASA side, without encrypts. I was debugging ICMP packets with the capture feature, and saw that echo-reply packets are returning toward the outside interface, but aren't passing through it.
capture test access-list test interface outside
1: 08:54:44.298980 802.1Q vlan#1 P0 x.x.x.x > y.y.y.y: icmp: echo reply
Where x.x.x.x is LAN and y.y.y.y is the VPN client ip. The nat is ok, access lists are ok, but the packets dont pass through.I tried creating new VPN profile but the same problem, it seems that only one remote client can be active even base license allows more than 1 client.
how to configure simple VPN access for a user to login to the corporate network and access the resource and get emails I do not want to use CA certificate for authentication instead a very simple method is what i plan to start up with the configuration step so i can test this out.
View 4 Replies View RelatedI'm configuring remote access on my cisco 881. Protocol PPTP was chosen.I've configured PPTP VPN access on my router, but there's an issue with accessing my LAN. I can access my Internet connection and open web sites, but I'm not able to access my local resources.I can only Ping my router's interfaces (192.168.2.10, 79.104.14.62) and Internet resources. For example, I can not ping switch, directly attached to the router, with address of 192.168.2.2 and other hosts on LAN.
View 1 Replies View RelatedWe plan to use ACS 5.3 for remote vpn user authorization. We have found a document on to how to do this, but they use ASA 8.3.we would like to know if it is supported on ASA 8.2 or do we need to upgrade the ASA IOS.
View 2 Replies View RelatedGot a single asa 5505 configured in the office. we have 3 site to site vpn connections from this device, which all work from within the office.Ive not setup my pc to connect from home to the asa via the ciso client.
i can connect to all LAN servers on the local subnet, however i cannot connect through the ASA to any of my site to site vpn's.
if i do an ipconfig on my home pc i can see my local ip, mask & gw, and i can see my assigned remote access ip & mask but no gw.
I cannot ping any remote site to site pc's by IP or name.
I have access to my enterprise network through Cisco VPN (software) client and it goes through remote-access ipsec vpn setup on an ASA 5510. Everything works fine.
But now users that connect to the enterprise network have in addition need to access remote sites networks that are connected through the site-to-site VPN tunnels: IPSec tunnels between mentioned ASA5510 and remote ASA5510s and ASA5505s in branch offices.
there is NAT exemption rule that exempts networks 10.1.10.0/24, 10.1.20.0/24, 10.1.30.0/24.All traffic from local network 10.1.1.0/24 have full ip connectivity with all the networks in branch offices. The PROBLEM is that remote vpn clients can reach only local network 10.1.1.0/24, but not the remote networks.
The ASAs in remote branch offices has set up NAT exemption towards both local network 10.1.1.0/24 and remote access clients network 10.0.5.0/28, but as I said, it doesn't go.
Remote access VPN. Its configured on a Cisco PIX525 running ver 6.3(5) (old I know!) and I am running Cisco VPN client ver 5.06.0160 on the client end. Ok so here's the thing. The client connects ok, and it gets an IP address no problem. But I cannot ping anything on the remote LAN. So the client is coming across the internet, the VPN adapter has a 192.168.1.1 address assigned by the PIX and I am trying to ping the 192.168.0.4 address assigned to a switch on the inside of the firewall but with no joy. [code]
View 1 Replies View RelatedI have a remote access VPN to our office network 10.42.10.0. however I have some web services that are located in a production network 10.42.1.0 that users in the office network need to access.This is obviously no problem when using remote desktop to an office PC but when users with laptops remote in and try to access the website on the production network it does not work.
Is there any way for the tunnel also to also allow traffic to the production network for the remote hosts?
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
[code]....