I am planning to implement RMON remote monitoring in my switch will it any huge effect on CPU utlization .Whether it is resource specific .
I am planning to monitor bandwidth utilization of all the ports in my lan using RMON . Is there any alternative o monitor bandwidth utilization ?I am using LMS 4.2
I need to use IP SLA to monitor remote routes on CAT6500
CAT6500 is running "sup-bootflash:s72033-jk9o3sv-mz.122-18.SXD7b.bin" on SUP720
Feature Navigator said it is
ENT FW W/MPLS/IPV6/SSH/3DES After drill down into feature set I found that this version support for IP SLA such IP SLAs - ICMP Path Echo Operation
BUT, back to console I can not do such (config) ip sla command (not found cmd CAT6500(config)# ip sla 1) What I did wrong or others cmd imply this ip sla process?
We have NAM-2 installed in 6500 chasis. Some times in GUI It does not analyse the traffic and shows the error msg"error communicating with RMon daemon". But at the same time we can login to NAM through CLI,
The issue resolves by reseting the module by hw-module switch "" module "" reset but not always and happens not very often,
Device details:
NAM application image version: 4.0(1a)
Maintenance image version: 2.1(5)
NAM Daughter Card Micro code version: 1.34.1.28 (NAM)
[Code].....
I have problem with my Cisco 6506E switch.when it reloads its going to RMON mode, If I give Boot command I. The RMON, then only it will get load with the iOS image.
View 2 Replies View RelatedRT1 is RR client of RT2, we run label BGP among RT1, RT2 and RT3; MPLS LDP is OK; RT1 network route 192.168.1.18/32 with MPLS-label 4123, we hope RT2 propagate it to RT3 by its address 192.168.8.2 and swap MPLS-label, however, RT2 just propagate it without any changing(192.168.1.18/32 nexthop 192.168.8.1).
router bgp 65000
bgp router-id 192.168.8.2
address-family ipv4 unicast
[code]...
I try to setup a basic GTS shaping on a cisco ISR G2 2900
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M3, RELEASE SOFTWARE (fc2)
Cisco CISCO2901/K9 (revision 1.0) with 1957856K/40960K bytes of memory.
ipbase ipbasek9 Permanent ipbasek9
the policy-map was applied to a svi interface (vlan interface)
And my problem is the shape isn't effective, in my attempt the max bw is 20Mb and I have gigabit interface
I know this kind of setup is classic and I see it working on older ios version 12.x
config:
interface VlanX
ip address X X
no ip redirects
[code].....
We need to rename our 4404 Wireless LAN Controllers. Would like to know if renaming via the GUI (change name in the Controller / General tab and then Apply) will cause the WLC to reload. Also wondering about the best way to push the name change to the APs (High Availability) - we are not using WCS.
View 5 Replies View RelatedMy internet provider give me 600kbps which is 0.6mbps i believe Wireless B's maximum speed is 11mbps N's is 300-450.Will I have any diffenece on internet speed between b and n? I use telus from vancouver they say I have 6mbps speed internet.
View 7 Replies View RelatedOk so this morning I found out that I had a running sql server that I did not know of. I think I might of got it with one of my development kits since I program with python, c# and java.Would I have got it from recently installed software.Also a big worry would it affect my internet and usage and will it affect my computers speed.
View 5 Replies View RelatedI have removed all port forwarding and enabled DMZ? I made sure the DMZ IP matches my internal IP. DMZ still not taking effect. One thing I noticed is that when I visited [URL] it showed a different IP then what was assigned to my router itself.
Modem > Linksys Wireless > Computer
Should the Linksys Wireless be in gateway or router mode?
I just update my cisco 7609 to Version 12.2(33)SRD6. I encounter a strange problem with this version, everytime i change BGP policy ( input or output ) this will take effect immediately without "clear ip bgp neighbor <address> soft". Are there anyway not to take BGP policy affect unless command "clear ip bgp neighbor <> soft" ?
View 7 Replies View RelatedWhat are the possible effects of assigning an invalid address like 172.22.0.0 255.255.255.252 to a router interface. The 1841 router accepted the address?
View 12 Replies View RelatedDoes ip default-gateway have any effect on a L3 device such as a 2811 router? I always thought that on a L3 device the default route would supersede any such command assuming it is accepted.
We have a client device that cannot be reached for managment directly and wanted to add that statment only if it might work.
I have Win 7 and Win 8 dual booting on my brand new Dell Vostro laptop. The wireless works beautifully while using Win 7, but when I switch to Win 8... the actual Fn+F2 wireless switch has no effect whatsoever! So I know the machine is OK, the network is OK, but what could be making the machine act differently under Windows 8? Device manager and details say the driver is up to date.. What do I look for next?? I don't think I'm going to be able to get a call through to Microsoft!!
View 3 Replies View RelatedI have a new catalyst 2960,and i want to enable DHCP SNOOPING,but,it doesn't work,the server is stilling offert addresses IP and it's not connected in a trusted port,the schema is very simple:1 switch catalyst 2960 PST-S,1 server dhcp and 1 pc client,the PC and the server are in VLAN 10,DHCP SNOOPING is enabled in all ports and no port is trusted,but the client get addresse IP after retyping ipconfig /release and ipconfig /renew in dos commande.the configuration and the version of the switch are in the file attached.I tested the same configuration in a catalyst C3560-24PS and DHCP SNOOPING work normally,i tested in other catalyst 2960-PST-S,but the same probléme:DHCP SNOOPING without effect,the commands typed is:
-ip dhcp snnoping
-ip dhcp snooping vlan 10
According to this Cisco URL jumbo frames should be put into play by changing default ethernet system class.
Recommended configuration:
!--- You can enable the Jumbo MTU
!--- for the whole switch by setting the MTU
!--- to its maximum size (9216 bytes) in
[Code].....
We have a RV016 load balancing between two broadband WAN connections. On protocols that are sensitive to a change in IP address such as ssh and https, if the client connection goes inactive for a short time (sometimes as short as 10 seconds), the RV016 often changes WAN connection as part of its "load balancing" feature. Most protocols do not even notice, but the more sensitive protocols do and often lock a session or timeout the session which is not a good thing.
We have been able to bind these sensitive protcolols to a particular WAN port but (in our minds) this is not an "ideal" situation. In fact I would consider this to be a broken "load balancing" solution and should be fixed.
determine whether I have QoS properly setup on my router, and why the rules do not appear to be taking effect.ISSUE We have a couple of laptops, smartphones, and a Wii on our home network. One device, my roommate's laptop, is a real bandwidth hog. It's connected (via internet, not VPN) to a work server and is frequently downloading and syncing large datafiles and media files.Unfortunately, when that laptop is downloading the other devices either cannot connect to the internet without timing out, or is VERY slow, for example pulling up websites like google.com. When that laptop is offline, everything works fine. It seemed like enabling QoS would resolve our problem.\
SETUPLinksys E1000, latest firmware (v2.1.02), using WPA2-Personal security.
We first tried enabling QoS and setting the MAC address of the downloading laptop to "low" priority and all others to "medium". No luck - the downloading laptop still seems to be hoarding the bandwidth.We also tried adding the download application to the list and setting the port to "low". Still no luck.We added a new application called "web" and set port 80-81 to "high", but that didn't work.We then disabled WMM support. No dice. The other devices still can't connect while my roommatte's laptop is syncing.We've fiddled around with the settings a bit, but no matter what, it looks like the QoS rules are not being applied.And is it acceptable to have multiple categories (MAC and application) in the QoS rules?
I have a SG 300 switch and configured it with public IP address.I can access it from anywhere within my network but not from outside my network as I'am not able to add the gateway and DNS address as there are are no fields to add them in the IP configuration menu in L3 mode.
View 1 Replies View RelatedI have desktop and two laptops. I have DSL connected with my desktop only. If I'm gonna install E200 so I can use my laptops in internet, wouldn't it effect my dsl connection in my desktop?
View 1 Replies View Relatedwe just bought a Cisco SG200-18 to replace our Linksys DLM2008 switches. Now we face a problem with remote desktop between our Win7x64 boxes.
Remote access is abysmally slow, but file transfer speeds seem to be normal. All ports are on Gigabit setting, jumbo frames disabled. The switch on the latest firmware.
I've just gotten a SG200-08 (SLM2008T-EU), which I would like to monitor remotely from Cacti using SNMP. It seems however, that this switch has no SNMP support - is this correct? Does this mean that there is no way to monitor traffic over the switch's ports short of making a script access the web UI?
View 1 Replies View RelatedSomeone hacked into my computer through my Netgear router. They took over as Administrator and setup a Atheros (sp) driver. They pretty much have total control over my computer. How can I rid myself of this hack and protect nyself in the future?
View 5 Replies View Relatedhow can I remote in to my router and I need to get past my router to my pc desktop
View 2 Replies View RelatedI am trying to connect to my office PCs via VPN and/or RDP. The office uses Qwest DSL and has a dynamic IP address. I use DynDNS.org to keep the DNS updated with the WAN address of the router. However, any attempt to access the network fails. I have tried remote management access (I enabled it on the router) but that fails. I forwarded RDP ports on the router to one of the PCs but can't connect to it. I also set up a VPN server but cannot connect to it either. Something tells me that all requests to myoffice.homeip.net are not getting to my modem/router. I have even tried the IP associated with the name (Yes, I did check that it is correct!) but nothing works there either.
View 1 Replies View Relatedi have a slow internet but my friend who live canada have high speed internet can use his internet . i do not want use his remote his computer but internet
View 5 Replies View RelatedI have two locations in the same city and I want to connect them together so I can share files and printers. Each of the LANs has a router and is a simple workgroup. LAN A uses 192.168.1.1 255.255.255.0; LAN B is 192.168.2.1 255.255.255.0. What is the best way to connect these two networks together so I can share printers on both sides? Should I replace the network routers, they are older and definitely could use an upgrade
View 3 Replies View RelatedMy boss is asking me to write a batch file or use a utility to monitor the uptime of 16 different ISP accounts that we use across several stores. Most stores have several ISP accounts setup as failover, so they're not always active on our network but the ISP should still be up. He would like this to run from one of our servers. He is suggesting the 'gateway' for the ISP however I am not sure how to find this IP. The tracert utility returns IP addresses which are different than the gateway address in our router settings so I am wary to use those IPs.Which IPs would I ping to monitor the uptime and where would be the best place to find them?
View 2 Replies View Relatedi provide 192.168.1.201 and port No.8150 in CP Plus DVR . I am able to login through Local system via IE with [URL] after pressing enter key Login window appears. I will type User ID as Admin and password 888888. now i am able to enter DVR and view all cameras. no problemin Beetal ADSL router ( ISP Router) i configured port forwarding as followsIP address 192.168.1.201 and Port No. 8150 both internal & external.Now i got internet IP address through MY IP Address.the IP address is 59.92.67.72 ISPs IP address for my Borad Band.through another internet with different different ISPI open IE and type [URL] got same loging window as in LANagain I enter User Id as Admin and password 888888but shows login failed Message through internet I got the same login window when i tried through LAN, but I am to unable login with a message login failed
View 1 Replies View RelatedIf switches on a network doesn't support remote port mirroring and only local port mirroring, What are the options to still capture all the traffic from all switches on 1 single core switch?
View 1 Replies View RelatedI have a Cisco 678 connected to my ISP (Qwest) using DHCP. This is connected to a Linksys WRT54g router. I also have a home server running for remote access to some files and media streaming. I just installed security cameras that I wish to monitor remotely via the internet.I can access my home files over the internet with no issue. However I am unable to access my cameras using the internet. Looking at my router incoming log, I see my request arriving, but I never get to the DVR attached to the camereas for remote viewing.I enabled bridging on the Cisco 678 but this did not solve the issue.
View 1 Replies View RelatedI am trying to Port Forward HTTP: 80, but my Router wont let me and it keep giving me this error message Status: Port Range Overlap with Remote Management.I have a NETGEAR CG814GCMR Router, I need to add that port for setting up a Game private server online, but my router wont let me, how to fix it?
View 12 Replies View RelatedWe have two ASA 5500 series Firewalls running 8.4(1). One in New York, another in Atlanta.They are configured identically for simple IPSecV1 remote access for clients. Authentication is performed by an Radius server local to each site.
There are multiple IPSec Site-to-Site tunnels on these ASA's as well but those are not affected by the issues we're having.First, let me start with the famous last words, NOTHING WAS CHANGED.
All of a sudden, we were getting reports of remote users to the Atlanta ASA timing out when trying to bring up the tunnel. They would get prompted for their ID/Password, then nothing until it times out.Sames users going to the NY ASA are fine.After extensive troubleshooting, here is what I've discovered. Remote clients will authenticate fine to the Atlanta Firewall ONLY IF THEY ARE USING A WIRED CONNECTION.
If they are using the wireless adapter for their client machine, they will get stuck trying to login to Atlanta.These same clients will get into the New York ASA with no problems using wired or wireless connections.Windows 7 clients use the Shrewsoft VPN client and Mac clients use the Cisco VPN client. They BOTH BEHAVE the same way and fail to connect to the Atlanta ASA if they use their wireless adapter to initiate the connection.
Using myself as an example.
1. On my home Win 7 laptop using wireless, I can connect to the NY ASA with no issues.
2. The same creditials USED to work for Atlanta as well but have now stopped working. I get stuck until it times out.
3. I run a wire from my laptop to the FiOS router, then try again using the same credentials to Atlanta and I get RIGHT IN.
This makes absolutely no sense to me. Why would the far end of the cloud care if I have a wired or wireless network adapter? I should just be an IP address right? Again, this is beyond my scope of knowledge.We've rebuilt and moved the Radius server to another host in Atlanta in our attempts to troubleshoot to no avail. We've also rebooted the Atlanta Firewall and nothing changed.
We've tried all sorts of remote client combinations. Wireless Internet access points from different carriers (Clear, Verizon, Sprint) all exhibit the same behavior. Once I plug the laptops into a wired connection, BAM, they work connecting to Atlanta. The New York ASA is fine for wired and wireless connections. Same with some other remote office locations that we have.
Below I've detailed the syslog sequence on the Atlanta ASA for both a working wired remote connection and a failed wireless connection. At first we thought the AAA/Radius server was rejecting us but is shows the same reject message for the working connection. Again, both MAC and Windows clients show the same sequence.Where the connection fails is the "IKE Phase 1" process.
-------------------------------------------------------------------------------------------------------------------------
WORKING CONNECTION
-------------------------------------------------------------------------------------------------------------------------
%ASA-6-713172: Automatic NAT Detection Status: Remote end is|is not behind a NAT device This end is|is not behind a NAT device
NAT-Traversal auto-detected NAT.
%ASA-6-113004: AAA user aaa_type Successful: server = server_IP_address, User = user
%ASA-6-113005: AAA user authentication Rejected: reason = string: server = server_IP_address, User = user
[code]...