Ok so this morning I found out that I had a running sql server that I did not know of. I think I might of got it with one of my development kits since I program with python, c# and java.Would I have got it from recently installed software.Also a big worry would it affect my internet and usage and will it affect my computers speed.
View 5 RepliesMy internet provider give me 600kbps which is 0.6mbps i believe Wireless B's maximum speed is 11mbps N's is 300-450.Will I have any diffenece on internet speed between b and n? I use telus from vancouver they say I have 6mbps speed internet.
View 7 Replies View RelatedAre the users' download speeds depend on the hosting company's owner's internet speed? Let say if I was running my own server with my internet speed 1mb and LAN 100mbps, are my clients' download speeds restricted to maximum 1mb of any content from my server?
View 3 Replies View RelatedRT1 is RR client of RT2, we run label BGP among RT1, RT2 and RT3; MPLS LDP is OK; RT1 network route 192.168.1.18/32 with MPLS-label 4123, we hope RT2 propagate it to RT3 by its address 192.168.8.2 and swap MPLS-label, however, RT2 just propagate it without any changing(192.168.1.18/32 nexthop 192.168.8.1).
router bgp 65000
bgp router-id 192.168.8.2
address-family ipv4 unicast
[code]...
I try to setup a basic GTS shaping on a cisco ISR G2 2900
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M3, RELEASE SOFTWARE (fc2)
Cisco CISCO2901/K9 (revision 1.0) with 1957856K/40960K bytes of memory.
ipbase ipbasek9 Permanent ipbasek9
the policy-map was applied to a svi interface (vlan interface)
And my problem is the shape isn't effective, in my attempt the max bw is 20Mb and I have gigabit interface
I know this kind of setup is classic and I see it working on older ios version 12.x
config:
interface VlanX
ip address X X
no ip redirects
[code].....
I have removed all port forwarding and enabled DMZ? I made sure the DMZ IP matches my internal IP. DMZ still not taking effect. One thing I noticed is that when I visited [URL] it showed a different IP then what was assigned to my router itself.
Modem > Linksys Wireless > Computer
Should the Linksys Wireless be in gateway or router mode?
We need to rename our 4404 Wireless LAN Controllers. Would like to know if renaming via the GUI (change name in the Controller / General tab and then Apply) will cause the WLC to reload. Also wondering about the best way to push the name change to the APs (High Availability) - we are not using WCS.
View 5 Replies View RelatedI have Win 7 and Win 8 dual booting on my brand new Dell Vostro laptop. The wireless works beautifully while using Win 7, but when I switch to Win 8... the actual Fn+F2 wireless switch has no effect whatsoever! So I know the machine is OK, the network is OK, but what could be making the machine act differently under Windows 8? Device manager and details say the driver is up to date.. What do I look for next?? I don't think I'm going to be able to get a call through to Microsoft!!
View 3 Replies View RelatedI am planning to implement RMON remote monitoring in my switch will it any huge effect on CPU utlization .Whether it is resource specific .
I am planning to monitor bandwidth utilization of all the ports in my lan using RMON . Is there any alternative o monitor bandwidth utilization ?I am using LMS 4.2
determine whether I have QoS properly setup on my router, and why the rules do not appear to be taking effect.ISSUE We have a couple of laptops, smartphones, and a Wii on our home network. One device, my roommate's laptop, is a real bandwidth hog. It's connected (via internet, not VPN) to a work server and is frequently downloading and syncing large datafiles and media files.Unfortunately, when that laptop is downloading the other devices either cannot connect to the internet without timing out, or is VERY slow, for example pulling up websites like google.com. When that laptop is offline, everything works fine. It seemed like enabling QoS would resolve our problem.\
SETUPLinksys E1000, latest firmware (v2.1.02), using WPA2-Personal security.
We first tried enabling QoS and setting the MAC address of the downloading laptop to "low" priority and all others to "medium". No luck - the downloading laptop still seems to be hoarding the bandwidth.We also tried adding the download application to the list and setting the port to "low". Still no luck.We added a new application called "web" and set port 80-81 to "high", but that didn't work.We then disabled WMM support. No dice. The other devices still can't connect while my roommatte's laptop is syncing.We've fiddled around with the settings a bit, but no matter what, it looks like the QoS rules are not being applied.And is it acceptable to have multiple categories (MAC and application) in the QoS rules?
I just update my cisco 7609 to Version 12.2(33)SRD6. I encounter a strange problem with this version, everytime i change BGP policy ( input or output ) this will take effect immediately without "clear ip bgp neighbor <address> soft". Are there anyway not to take BGP policy affect unless command "clear ip bgp neighbor <> soft" ?
View 7 Replies View RelatedWhat are the possible effects of assigning an invalid address like 172.22.0.0 255.255.255.252 to a router interface. The 1841 router accepted the address?
View 12 Replies View RelatedDoes ip default-gateway have any effect on a L3 device such as a 2811 router? I always thought that on a L3 device the default route would supersede any such command assuming it is accepted.
We have a client device that cannot be reached for managment directly and wanted to add that statment only if it might work.
I have desktop and two laptops. I have DSL connected with my desktop only. If I'm gonna install E200 so I can use my laptops in internet, wouldn't it effect my dsl connection in my desktop?
View 1 Replies View RelatedI have a new catalyst 2960,and i want to enable DHCP SNOOPING,but,it doesn't work,the server is stilling offert addresses IP and it's not connected in a trusted port,the schema is very simple:1 switch catalyst 2960 PST-S,1 server dhcp and 1 pc client,the PC and the server are in VLAN 10,DHCP SNOOPING is enabled in all ports and no port is trusted,but the client get addresse IP after retyping ipconfig /release and ipconfig /renew in dos commande.the configuration and the version of the switch are in the file attached.I tested the same configuration in a catalyst C3560-24PS and DHCP SNOOPING work normally,i tested in other catalyst 2960-PST-S,but the same probléme:DHCP SNOOPING without effect,the commands typed is:
-ip dhcp snnoping
-ip dhcp snooping vlan 10
According to this Cisco URL jumbo frames should be put into play by changing default ethernet system class.
Recommended configuration:
!--- You can enable the Jumbo MTU
!--- for the whole switch by setting the MTU
!--- to its maximum size (9216 bytes) in
[Code].....
We have a RV016 load balancing between two broadband WAN connections. On protocols that are sensitive to a change in IP address such as ssh and https, if the client connection goes inactive for a short time (sometimes as short as 10 seconds), the RV016 often changes WAN connection as part of its "load balancing" feature. Most protocols do not even notice, but the more sensitive protocols do and often lock a session or timeout the session which is not a good thing.
We have been able to bind these sensitive protcolols to a particular WAN port but (in our minds) this is not an "ideal" situation. In fact I would consider this to be a broken "load balancing" solution and should be fixed.
I am sutdying at uni and in a few months, I will be moving into a house, with my current flatmates. We will be buying a fibre optic line.Ideally,what I want to do, is split the connections evenly,depending on how many people are online current, rather than having mass downloads of everyone at the same time, when other will only get a small speed while browsing or gaming,or streaming,etc.So, basically, what I want to do is split the connection at anyone time evenly,so if there are 5 people connected and our connection speed is 50MB then each will get 10MB. And if 2 people are connected, then the speed will be 25MB each, and so on.
I am wondering what is the cheapest way of doing this? I am very computer illerate,I know how to use unix systems.I even own my own server, but I'm not so clued up in this area of networking.I believe it's something to do with a switch, and which switches support this? (I've heard it's something to do with full-duplex / half duplex).
- I will probably set up a domain system, where everyone has to login to the main server to access the internet. (I know vaguely how to do that) - is there some software that I can put on the server which will distribute connection speeds automatically.
with SOTFWARE to reduced the speed of my cybercafe server against my client that eat up my bit( reducing the speed of heavy downloading
View 1 Replies View RelatedWhat would be the ideal download and upload speed for a server of more than 50 people ?
View 1 Replies View RelatedI have a Netgear DG470N gigabit modem and I am streaming 1080P films from a 2TB networked hard drive onto a LG 42inch Smart TV viat wired ethernet. Sometimes the films crash and the TV cannot reopen the network folder with the film in until a reset is done on the modem. Is there a high speed gigabit switch that I can use to improve this or should I get some media controlling software?
View 3 Replies View RelatedIn my last thread I had difficulties setting up access to my FTP server through the RV220W router. After getting it to work, I faced a new issue of reduced upload speed. 240ish KB/S which is obviously ridiculously slow. After much toying around, I finally got it to work again, after doing a factory reset of the router. But today when I wanted to upload to my friends NAS, I suddenly am faced with reduced speeds yet again(400KB/S)! settings, with one firewall rule added, to allow access to my FTP. Other than that, I also enabled jumbo frames....so I tried disabling that again. But that did nothing. Also tried disabling every firewall feature under "attack prevention" but, didn't seem to work either.I didn't reboot the router with each change, as that would make things take a lot longer....and didn't think it should be necessary?
I'm starting to get more and more tired of using my RV220W....seems slow and buggy..when I do a online speedtest, I get a 30Mb/30Mb down/upload rating, which matches the rating I pay my ISP for.... And I have a fiber connection.
[code]...
I am able to obtain IP addresses through the DHCP server for my clients and I am able to browse internet on the server 2k8.Server 2008 - Share Internet through DHCP server
I have a small home network of around 5 PCsI have 8MB shared connection from ISP so when I run speed test check from one of my PC it returns around 1.76 Mb download and 0.07 Mb Upload Speed my question is, if I connect one of the PC directly to modem and run the test again so will I get 8MB of speed?
View 1 Replies View Relatedi have high speed internet from charter(i know they are not the best but more on that later) with actually download speeds tested online around 10-13mbps on average. i keep my computer pretty clean, running smart defrag, cleaning the disk, anti virus, only have programs running in the background that are needed, have increased my virtual memory and also use readyboost with a 4 gb flashdrive that i allow to use all the flashdrive memory as "ram" memory. so i think this has be something below the surface and that i cannot handle on my own. i do not think it is my internet provider because i have to roommates that have computer and they have no problem usually with the internet. when i say usually i mean they have problems sometimes maybe 3-4 times weekly where i have problems at least 2-3 times a day.
View 1 Replies View RelatedOkay so I just upgraded internet speed to 6Mbps My laptop is getting around 5.8Mbps which is fine but my PC is only getting 1.5 Mbps?
View 3 Replies View RelatedI signed up for a 384 Kbps adsl like but when I download something I get a speed of 40 kbps!
View 4 Replies View RelatedI've got 45mbps internet speed with Windows XP and 0.8 with Windows 7..
View 6 Replies View Relatedhow to speed up my internet connection through registry or any other easy way to increase speed?
View 1 Replies View Relatedevery devices on my network started having really slow speed. It takes long time for each to navigate thru sites. Normally every device gets around 20-25 MBPS in the network. And i have desktop, laptop, iphone, tablet on the network. I've been trying to fix this for whole day yesterday and today and no luck.how to fix this?.I ran some things from this site and the results are here.
[code]...
I have tested internet speed on Ethernet (~20 Mbps), but when I'm connected via wifi network, it drops down to ~11 ? The speed is same on all wireless devices even when I sitting next to the wifi router.
View 8 Replies View RelatedHow can I optimize my computer's connection speed? I'm using a Dell Vostro 1500 laptop, and I used to have Vista installed on it. When I used that, my connection(via speedtest.net) was around 25mbps. I reformatted it last Summer and installed Windows XP Service Pack 3 onto it. A few months ago, I used speedtest.net and my speed test was around 16mbps. Now, my speed test is 8mbps. How can I optimize my internet connection speed? My internet service provider is Comcast.
View 3 Replies View RelatedI am having trouble with my internet speed at my computer my provder says the speed is fine from their end 100mbps but when i check the speed at my end i am only getting 32mbps the other clue is when I am on a web page it constantky flickers. I have reset the router by turning off the power and then back on the other thing i have done is change the ethernet cable.
View 1 Replies View Related