My internet provider give me 600kbps which is 0.6mbps i believe Wireless B's maximum speed is 11mbps N's is 300-450.Will I have any diffenece on internet speed between b and n? I use telus from vancouver they say I have 6mbps speed internet.
View 7 RepliesOk so this morning I found out that I had a running sql server that I did not know of. I think I might of got it with one of my development kits since I program with python, c# and java.Would I have got it from recently installed software.Also a big worry would it affect my internet and usage and will it affect my computers speed.
View 5 Replies View Relateddetermine whether I have QoS properly setup on my router, and why the rules do not appear to be taking effect.ISSUE We have a couple of laptops, smartphones, and a Wii on our home network. One device, my roommate's laptop, is a real bandwidth hog. It's connected (via internet, not VPN) to a work server and is frequently downloading and syncing large datafiles and media files.Unfortunately, when that laptop is downloading the other devices either cannot connect to the internet without timing out, or is VERY slow, for example pulling up websites like google.com. When that laptop is offline, everything works fine. It seemed like enabling QoS would resolve our problem.\
SETUPLinksys E1000, latest firmware (v2.1.02), using WPA2-Personal security.
We first tried enabling QoS and setting the MAC address of the downloading laptop to "low" priority and all others to "medium". No luck - the downloading laptop still seems to be hoarding the bandwidth.We also tried adding the download application to the list and setting the port to "low". Still no luck.We added a new application called "web" and set port 80-81 to "high", but that didn't work.We then disabled WMM support. No dice. The other devices still can't connect while my roommatte's laptop is syncing.We've fiddled around with the settings a bit, but no matter what, it looks like the QoS rules are not being applied.And is it acceptable to have multiple categories (MAC and application) in the QoS rules?
What are the possible effects of assigning an invalid address like 172.22.0.0 255.255.255.252 to a router interface. The 1841 router accepted the address?
View 12 Replies View RelatedDoes ip default-gateway have any effect on a L3 device such as a 2811 router? I always thought that on a L3 device the default route would supersede any such command assuming it is accepted.
We have a client device that cannot be reached for managment directly and wanted to add that statment only if it might work.
I have desktop and two laptops. I have DSL connected with my desktop only. If I'm gonna install E200 so I can use my laptops in internet, wouldn't it effect my dsl connection in my desktop?
View 1 Replies View RelatedAre the users' download speeds depend on the hosting company's owner's internet speed? Let say if I was running my own server with my internet speed 1mb and LAN 100mbps, are my clients' download speeds restricted to maximum 1mb of any content from my server?
View 3 Replies View RelatedRT1 is RR client of RT2, we run label BGP among RT1, RT2 and RT3; MPLS LDP is OK; RT1 network route 192.168.1.18/32 with MPLS-label 4123, we hope RT2 propagate it to RT3 by its address 192.168.8.2 and swap MPLS-label, however, RT2 just propagate it without any changing(192.168.1.18/32 nexthop 192.168.8.1).
router bgp 65000
bgp router-id 192.168.8.2
address-family ipv4 unicast
[code]...
I try to setup a basic GTS shaping on a cisco ISR G2 2900
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M3, RELEASE SOFTWARE (fc2)
Cisco CISCO2901/K9 (revision 1.0) with 1957856K/40960K bytes of memory.
ipbase ipbasek9 Permanent ipbasek9
the policy-map was applied to a svi interface (vlan interface)
And my problem is the shape isn't effective, in my attempt the max bw is 20Mb and I have gigabit interface
I know this kind of setup is classic and I see it working on older ios version 12.x
config:
interface VlanX
ip address X X
no ip redirects
[code].....
I have removed all port forwarding and enabled DMZ? I made sure the DMZ IP matches my internal IP. DMZ still not taking effect. One thing I noticed is that when I visited [URL] it showed a different IP then what was assigned to my router itself.
Modem > Linksys Wireless > Computer
Should the Linksys Wireless be in gateway or router mode?
We need to rename our 4404 Wireless LAN Controllers. Would like to know if renaming via the GUI (change name in the Controller / General tab and then Apply) will cause the WLC to reload. Also wondering about the best way to push the name change to the APs (High Availability) - we are not using WCS.
View 5 Replies View RelatedI've recently bought a 3G, 32MBit/sec (DC-HSPA+) connection with a ZTE MF680 Modem and a Dovado 3GN router. When I connect the modem directly to the computer I get around 20-25MBit/s which is great and acceptable. Problem is when I connect through the router I get max 3Mbit/sec.Connected via ethernet cable or Wireless (n/b+g+n) gives the same low speed results I have used the same APN (bredband.tre.se) in my router as is on the modem I have upgraded to the latest firmwares on the Router (latest firmware 5.0.5-3)I have swaped my modem to another one, to the Huawei E372 (latest firmware 11.203.05.00.00).
I have swaped my Router to another Dovado 3GN and updated to the latest firmware The modem is placed 2meters away from the router to reduce interference I have removed all my anti-virus and firewalls and I believe the router has no firewall and prior to that did a virus check, also with spyware doctor. I changed the SIM card, and got another from the ISP, no luck. The router's support says they recieve full speed (like 20Mbit) with the same hardware and firmware combination The 3G modem is exactly in the same place where I do the speed tests Speedtests done with [URL] and [URL] Pings are quite high in both cases when doing tracerts but while doing the speedtests they are between 45ms and 75ms?I have moved the config to another room, same results I have tried using no security on Wifi and also disabling WiFi. I have tested with 4 differnet computers with totally diffferent configs
[code]....
I currently have a 802.11 G router of 54mbps (its claims its a super G 108 mbps tough). My notebooks have 802.11 N built in. Im thinking of upgrading my router to a 802.11 N 300mbps.However, I know that this may be irrelevant unless I have a internet conection that can achieve such speeds. So how do I test my internet speed to see if G is bottlenecking?
View 4 Replies View RelatedI have had the DIR-825 since the beginning of the year connected to AT&T DSL Internet 3GB. I just upgraded to their 6GB download speed and didn't see any change in speed and suddenly I couldn't view my SlingBox anymore outside the house. I connected one computer directly to the modem, ran the AT&T speed test and got >5GB download and @700 upload. Wired via 1GB network back to the router, ran the speed test and it dropped to @4GB download and 120 upload.
I called AT&T, they checked everything, and said there was nothing wrong. I then spent almost an hour on the phone with D-Link including getting passed to 3rd level support. I knew something was wrong when the guy told me that since it was only a 1GB router, I shouldn't expect to get faster than 1GB Internet download.
The router is still running the 1.00 firmware and these are the changes they made me try so it's still sitting at these settings:
- Change the WAN from Auto 10/100 to 100 only.
- Change MTU to 1482 in my PPPoE settings
- Change Firewall Settings to turn SPI off. He said the router is still providing a firewall though.
He wanted me to download the 1.01 firmware but I balked and he said it probably wouldn't do any good. It ended with him wanting me to call AT&T back and set the modem to bridge mode. I then need to call them back and set the PPPoE again. This 3rd level support guy was very rude and am hoping to avoid calling them again.
Before I go through the hassle of calling AT&T and trying this bridge mode, or has the Elite 6GB service from AT&T and are having it work correctly.
I have Win 7 and Win 8 dual booting on my brand new Dell Vostro laptop. The wireless works beautifully while using Win 7, but when I switch to Win 8... the actual Fn+F2 wireless switch has no effect whatsoever! So I know the machine is OK, the network is OK, but what could be making the machine act differently under Windows 8? Device manager and details say the driver is up to date.. What do I look for next?? I don't think I'm going to be able to get a call through to Microsoft!!
View 3 Replies View RelatedI am planning to implement RMON remote monitoring in my switch will it any huge effect on CPU utlization .Whether it is resource specific .
I am planning to monitor bandwidth utilization of all the ports in my lan using RMON . Is there any alternative o monitor bandwidth utilization ?I am using LMS 4.2
AOL are a complete waste of time and space in my opinion as for one you cannot understand what there tech support is saying and even when you email there tech support they seem to answer with a totally different answer to my questions.I have just installed a pci card ethernet connection on my pc windows xp now all I want to now do is connect and configure my router on the internet, I currently use aol dial.bb broadband adsl connection so far there are no connections from the router connected to my pc as i am still using a bt voyager 105 modem.When i did connect the ethernet cable to my pc and into the router also i connected the adsl cable into the back of the router but aol have not explained how to connect to the internet to configure this router and get it to work.
View 2 Replies View RelatedI have a wireless Netgear WGR614v5 router, 54Mbps which is approx 6 yrs old. I also have the high speed cable internet service that provides up to 10 Mbps DL speed. Since my router still works, is there any reason I should replace it or is it possible it degrades in speed as it ages?
View 9 Replies View RelatedI am getting very slow internet speed through cyberoam firewall router. THE VPN & BROWSING ARE VERY SLOW EVEN THOUGH THE ISP SPEED IS 25MBPS.
View 1 Replies View RelatedMy ISP is Sky who I use for phone calls and internet, the line to my my house was installed by BT several years ago. I live in a fairly rural area and have never had more than a 1.5mb connection.
Two months ago a neighbor who was repairing his guttering accidentally broke the main phone line coming from the pole directly to our house (the ladder he used was left unattended and it fell over catching on the wire). The line broke in the middle of the length that runs from the pole directly in front of our house to the connecting shackle on the house fascia board, on the first floor.
I connected the broken wire back together, I only have one line in, so all that needed to be soldered were the white and orange wires. The other colored wires I cut flush. The remaining three steel core wires i used as holding wires. Everything was heat shrink sealed, insulation taped up, heat shrink over the whole lot and then more insulation tape put over the whole join, allowing around three or four inches over run at each end of the join. Afterward I did a quiet line test (17070 option 2) and the line was good. My internet speed was as per usual, 1.5mb.
Last Wednesday I was checking my email and web pages kept timed out, i logged on to the router and checked the speed I was connected at. My speed was 560kbps / 56k. After several router resets the speed was still not any higher. I did a quiet line test again and there was a considerable amount of line noise.
As it had rained a few times since my repair to the wire I thought it best to check to see if any water had gotten in. Unfortunately, even with all the insulation water had indeed got in. There was a score mark on the cable and that was the obvious route of entry. Upon opening the repair back up I could see the copper wire inside the orange line had turned black. I had to cut back the damaged line about 10 inches total, to get shiny copper cable and remove the scoring on the outside of the cable. I re-joined the line as I had done before. A quiet line test was good, but my internet speed remains at 560kbps / 56k.
I bought a new ADSL filter, and have tested the router directly in the master test socket without my phone extension, no difference in internet speed at all, and like I said the quiet line test is perfect.
Before I bite the bullet and get BT to come and renew the cable (which I am going to get done, when my neighbor can afford it) is there anything that I could have overlooked, or is it possible that the water has damaged something i.e. the Sky router or other parts of the cable?
I have a problem with my internet speed when i use cisco router 2911, the speed is very low. when use the ADSL router of my ISP ( the router is CNET), i don't have probleme. all test that i have do is without my lan juste 1 computer connected to routers.
I have HWICADSL card
Router 2911 withe ios 15.
My real speed is 8Mo.
I just update my cisco 7609 to Version 12.2(33)SRD6. I encounter a strange problem with this version, everytime i change BGP policy ( input or output ) this will take effect immediately without "clear ip bgp neighbor <address> soft". Are there anyway not to take BGP policy affect unless command "clear ip bgp neighbor <> soft" ?
View 7 Replies View Relateddo you think there would be a visible (or negligible) difference in internet speed if I used a hardware firewall as opposed to the router's inbuilt firewall?So assuming that all switches/ports were Gigabit Ethernet compatible (including the firewall itself), would it be a better idea to turn off the router/modem's firewall and use the hardware firewall, or would it be best to just stick with the router firewall?The reasoning behind this is that I'm not a big fan of Netgear... or their firewall system. After recent DDoS attacks (and IP address changes), I've decided to put a computer that was lying around to good use - Use it as a (Linux) firewall. iptables, here we come. - Yes, the Netgear router (CVG824G) has died a few times. Probably going to get upgraded to a NG CG3000, which uses (more or less) the same firewall system, I assume.
View 6 Replies View RelatedI currently use a Linksys E3200 and mainly direct connect it to my laptop. My current ISP is with Insightbb to which I use their 20.0 (20 Mbps) service. For the past 6 or 7 months I've had little to no issues with my internet connection until about a week ago. While directly connected to the E3200 I used to get up to about 20/21 Mbps at a constant rate. Yet now I'm lucky to get up to 13/14 Mbps. Also, the speed will sometimes fluctuate; shooting to as low as 8 Mbps and shooting as high as15 Mbps. I can verify that my ISP is not the issue. I've directly connected my laptop to the modem with success and received a healthy speed of up to 23 Mbps with no fluctuations. The problem only occurs once I directly connect to the router. Attempting to connect wirelessly shows the same, if not worse, problems.
I've attempted numerous factory resets and used the 30:30:30 method to no avail. I've tried power cycling the modem, router and laptop. I've tried disconnecting the router for up to 10 minutes. I've upgraded the firmware to the most recent update. I've tried setting a static IP. I've tried imputing the MTU manually. I've tried setting a MAC address clone. I've tried turning on/off UPnP. I've tried release/renewing my IP address. I've tried flushing my DNS. All of which I power cycled the router after each and every attempt.
I've recently purchased a WRT160N router, and I'm using it in conjunction with a WMP54G wireless PCI card. I've set the router up to my requirements, and can get a stable wireless connection.. but internet speed seems excessively slow. While I'm able to get up to around 4MB/s transferring files over the network, running speed tests, it consecutively shows my download speed to sit around 400KB/s, whereas I'm able to get a steady 1.1MB/s on another desktop that is wired. Disabling the LAN adapter on that computer, and connecting via wireless, brings down the speed that that computer is able to get to around 400KB/s as well. Hence, I don't think it's my wireless cards, but something to do with the router itself.I'm also experiencing lag spike issues in online games, which I can only attribute to the current wireless setup, because I've previously had no issues with it. All relevant ports are forwarded, so that is not an issue.After doing some Googling on the subject, someone had suggested running SpeedGuide's TCP Optimizer, and changing the RWIN - I ran it, and set it to the 'optimal' settings, and after a reboot the wireless seemed fine - I was getting just a tad under what I should (about 950KB/s).. but after a short while, it just went back to 400KB/s. After further investigation, it seems that Vista automatically changes that RWIN value to optimize network traffic.. but I never had this issue with my old wireless gear, so I can only assume that the way Vista is reacting is based on the way the router is interacting with it.
View 9 Replies View RelatedI have a E3000 router and I want to slow the upload and download speed to my Xbox is there any way to do this thru the router settings. I have internet that is about 20-30mbps down and 2-3mbps up I want to slow it to about 5-6mbps down and 1-2 mbps up.
View 2 Replies View RelatedI've a problem with the internet speed of my ADSL line(20Mega). Now I've the following components: D-link DSL-320 B (modem)+Cisco Linksys EA6500. If I start a Speed test the result its only 4M in download, while i remove the router and i connect my Pc directly to modem, the speed test results its 13-14M.
View 3 Replies View RelatedI came home yesterday and my Internet was really slow. I later found out that it was due to my Linksys E3000 because if I bypass my E3000 and go directly to my cable modem, it work just fine.I tried reconfigure, update firmware, factory reset and none of these has worked.
View 8 Replies View RelatedI have Wrt610n V1 Firmware V 1.00.03 B15 and internet 300 mb.If i connect PC to my internet bridge i have 300 mb. But when I switch between a WRT610n all ports have ~100mb. In router I removes all check marks from all security, filter.
View 6 Replies View RelatedI got 1Ggbit Internet. When i plug in PC i got 700+300+ on speedtest, if i plug in E3200 i got 9040. **bleep**?I play with all settings nothing works... In status he show 1 ggbit internet and 1 ggbit Ethernet but he gives less than 100 mbit....
View 9 Replies View RelatedI have an E2000 Wireless N Router setup to use WPA2/AES. I have Comcast cable internet service and I just upgraded to the 50Mbps speed. I have a Motorola Surfboard modem (DOCSIS 3.0).
If I connect my computer directly to the modem or to one of the ports on the E2000 I get great speeds sometimes up to 60Mbps but on average I am getting 45-48Mbps which is acceptable.
When I try to connect the same computer to the E2000 wirelessly my speed tests return a horrible 18-22Mbps. When I run these tests the computer is in the same room as the router. As I move throughout my house the speed tests are the same. My wireless connection speed to my laptop is good 144Mbps and 300Mbps depending on the band (2.4 or 5.0).
I have tried to use the 2.4ghz and 5.0ghz using different channels. I have also tried different "N Transmission Rate" settings. One of them (5 - 52Mpbs) does increase the speed to around 25-26Mpbs but that is all.
Strangely (or maybe not) the upload speeds are consistent on all of the tests at around 12Mpbs.
I am using Speedtest.net and Speakeasy for all of my tests.
Is there anyway I can get my wireless download speed up to around 40Mpbs? Or am I going to have to run cables through my house to the devices where I need these high speeds?
I also have upgraded to the latest firmware version.(1.0.04)
We recently purchased a Linksys E3200 router, because our old router didn't take advantage of our internet speed. The router works fine, though the internet speeds again isn't as much as expected.
With a wired connection, we only get 80 Mbit/s of our full 120 Mbit/s, according to Speedtest.net. The Cisco Connect built-in speed test is even worse; only 40 Mbit/s. When we directly plug the computer into the modem, we get the full 120 Mbit/s, which indicates that the modem does have the connection speed. The router just doesn't give it to the computers attached.
I don't know about my wireless speed, as my wireless card in the laptop clearly is the bottleneck (it can only connect at 65 Mbit/s). Atheros AR9285 ftw.
We tried different cables, the one included with the router gives the same speed.
I just bought a Cisco e1200 router... and the wireless connection is way too slow, when navigating through the web, but when using speed test, the connection seems fine, but still it even takes more than usual to open simple pages, lets say Google... i usually watch streams and now that i cannot do... when i connect directly i can do everything as usual...as i have read, i change channels, but still no improvement, i have the latest firmware, on my range there are only 2 more available connections... i even tried disabling/enabling the WMM... We all know that having extremely slow internet must be the real "Mayan apocalypse"
View 2 Replies View Related