I see a topology, I wonder if this topo can work?two ASA config active/standby ASA is VPN server, two fortigate firewall config active/passive.Normally I see ASA must config: inside, outside, .. . and vpn config.But this topo, ASA may not have inside, outside.
View 4 RepliesI have a L2L VPN tunnel on a Cisco ASA 5520 that I'm trying to get RRI to work on. On my cryptomap ACL I have defined a local object-group and a remote object-group, and I'm performing one-to-one NAT on the local group. I also have a route map configured that will take the static routes and redistribute them into my EIGRP AS. Two things I've noticed -1, I'm not seeing any static routes on my ASA that point to the remote subnets, and 2, the ACL that I've used in my route map definition is not getting any hits on it.
View 2 Replies View RelatedWe have Cisco ASA 5520 with csc ssm 10 (product ver. Trend Micro InterScan for Cisco CSC SSM 6.6.1125.0)in Web>Global settings> URL filtering > Rules > Communications and Search> Social Networking category is set to block during work time and allow during leisure time(see the attachement), but rule for this category won't work. I mean social networking sites are always remain allowed.
View 2 Replies View RelatedI have an asa 5520 that works fine if you are using passive ftp and ftp inspection is on globally. It is not working for an active ftp session. I tried allowing all ports back to the external ip address of the internal client as a test and this did not work either.
Cisco Adaptive Security Appliance Software Version 8.0(3)
Device Manager Version 6.2(3)
policy-map Global_Policy
[Code].....
I read another article saying that this command needs to be on the asa "fixup protocol ftp 21"
If this is enabled will it show on the firewall? How do I enable it?
I am having ASA 5520 with active/standby configured. Around 2 days ago, the ASA stopped responding & all of my websites stopped working. when i checked the failover status it said that failover is off. I had to manually turn the failover to start my traffic flow.During this time my secondary ASA was not responding. After some time, the primary stopped responding & secondary became active......to solve this i had to make the secondary unit as failover unit primary & the primary unit as failover unit secondary. i did get a log on ASA :-
“(Primary) Disabling Failover” with error message no.105001 which states the below:-
Error Message %PIX|ASA-1-105001: (Primary) Disabling failover.
Explanation In version 7.x and later, this message may indicate the following: failover has been automatically disabled because of a mode mismatch (single or multiple), a license mismatch (encryption or context), or a hardware difference (one unit has an IPS SSM installed, and its peer has a CSC SSM installed).(Primary) can also be listed as (Secondary) for the secondary unit.
Are the ASA memory DIMMs created for specific models? Would a 1GB 5510 Memory stick work in a 5520?
View 1 Replies View RelatedI got a question a about is there a Cisco VPN client that can be used with Honeywell PDA and Cisco ASA?
* Firewall
Cisco ASA 5520
IOS: asa832-k8.bin
* PDA
Brand: Honeywell
Model: Dolphin 7800
O.S. Windows Embedded Handheld 6.5 Professional
I have set up a remote access ipsec vpn on an asa 5520. I can connect, and ping internal ip addresses, however I cannot ping back out to the internet, nor can the internal network ping the vpn clients and dns resolution internal or external does not work. I am seeing nothing blocked in the logs on the asa.
View 3 Replies View RelatedI installed Windows 8 on my Dell laptop and my bluetooth device doesn't work properly. When Windows 7 was installed and my laptop and my Samsung Galaxy S3 were paired I could play songs from my phone on my computer. But now it is not possible on Windows 8.
View 1 Replies View Relatedit keeps disconnecting and ping breaks all the time.other laptop and phones work fine.and if i go 5-10 meters away from router it gets worse.tried new drivers and bios.even tried to change settings of wireless card still problem is there.
View 5 Replies View RelatedI am using ASA5520 with webvpn for file sharing. But recently we just upgraded the OS that accommodate file shared folder from win2003 R2 32bit to windows server 2008 R2 64bit. Now I have a problem with accessing file share by ASA webvpn, it appears error contacting host, we have tested the file shared of webvpn on the other OS windows 2003 and windows 2008, they are working on these OS except win2008 R2. Current the ASA OS version is 8.0(2). And the windows firewall has been disabed.
View 3 Replies View RelatedWe are using the newest release of AD Agent (1.0.0.32.1, built 598). The ASA Firewalls 5520 are having the software release 8.4(3)8 installed.When somebody tries to connect thru the Identity based firewalls from a citrix published desktop environment (PDI) the connection is not possible. Checking the ip-of-user mapping on the firewalls (show user-identity ip-of-user USERNAME) mostly doesn't show the mapping of the USERNAME and the PDI the user is logged in. The user-of-ip mapping of the PDIs IP-address shows mostly other users, which then are used to authenticate the acces thru the firewalls.
What is interesting, that on the AD Agent using "adacfg.exe cache list | find /i "USERNAME"" i can't see the PDIs IP-address neither because it is mapped to another user.Is Citrix Published Desktop environment supported to connect thru Identity based Firewalls? How AD Agent, Domain Controllers and Firewalls are working together? On the firewalls with "show user-identity ad-agent we see, the following:
-Authentication Port: udp/1645
-Accounting Port: udp/1646
-ASA Listening Port: udp/3799
Why Cisco does use 1645 and 1646 and not 1812 and 1813?The Listening Port is used for what purpose? we tried the AD Agent modes full- download and on-demand with the same effect.
Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies View RelatedWe were using ASA-5520-K9 with ASA-SSM-AIP-20-K9 but recently found some hardware problem in our running ASA. Now cisco want to replace with ASA-5520-K8.
View 1 Replies View RelatedI'm trying to set up my DIR-655 so I can use VPN to access my work PC. How can I set this up?
View 2 Replies View RelatedI have a DIR-655 B1 router. The firmware is 2.00 NA. Just to clarify, the DSi itself does work with WPA, but the games only work with WEP. I made a guest account and set it to WEP and it still does not work. I have tried making the main connection WEP as well, but when I go on the game and try it, it says it is WPA and not WEP. My friend has a DIR-655 as well, but the hardware and firmware version are different. Her games work flawlessly.
View 10 Replies View RelatedAfter having a hard time getting the VPN back to default, I logged into the ASDM and reset to factory defaults. After it reset, I logged in via the management port and configured everything to work. When I clicked on "apply", it gave an error saying that the inside interfaces, g0/1, IP address is on the same network as the management interface. When the ASA restarted, I am now unable to get into the unit via the management port or the inside interface.
I had set the management port to 10.0.1.254. WHen I connect an ethernet cable to it and place my mac on the the same network, I can ping the management interface, however I cannot SSH, Telnet or ASDM into it.
Here is the big problem, I don't have a console/rollover cable to connect to the console interface. Is there another way I can default the box? Maybe via the reset button on the back somehow? Or, is there a way to figure out the ip address of the inside interface? I'm assuming, since it did not take the IP I set, that it defaults to something right?
I cannot seem to ping between devices on two networks hanging off a 5520 unless I use the same-security interface command. I have the relevant ACL's set up between the interfaces, but it just doesnt work unless I have that command in - if I use that command, it bypasses the ACL.
Config
interface GigabitEthernet0/0.224
description NMS
vlan 224
nameif NMS
security-level 100
ip address 10.11.120.225 255.255.255.240[code].....
We are attempting to implement an ASA 5520 with a new ISP. Based on the limited routing needs, I believe we can use it as the router as well. I am familiar enough with routers, but the ASA is obviously a different thing.
The setup looks like:
ASA Version 8.2(1) !
host name Cisco
interface GigabitEthernet0/0description Internet name if Outsidesecurity-level 0ip address 69.XX.46.1 255.255.255.252 !interface GigabitEthernet0/1
description DMZnameif DMZsecurity-level 0ip address 69.XX.56.1 255.255.255.240
!interface GigabitEthernet0/2description Localnameif Insidesecurity-level 15ip address 10.0.XX.XXX 255.255.252.0
[Code] .....
1) Outside 0/0 connects to MRV from service provider (Public)
2) DMZ 0/1 connects to outside switch with servers (Public)
3) Inside 0/2 is LAN (Private)
A) Based on a completely default config and aside from setting the routes to send traffic from inside to outside, and outside to DMZ, what is the next step?
B) What should the interface security levels be, I am unsure what they should be or why...?
Based on the initial config with interfaces set as above, I cannot move traffic through.
I got a VPN request form from one of our partners. On my side I have one ASA 5520 running 8.0(3) On their form, It says that their endpoints are two boxes, sitting on different cities, It also says that there is only one encryption domain, (actually just one IP) that I need to speficy on the VPN setting. It looks like they mean that you could access the same encryption domain from any of the two Boxes in different cities. This is strange to me, since every time I have set up VPN before, each endpoint has their own encryption domains.I never seen two enpoints with the same encryption domain behind, so Im confused wether it might be a mistake on their part, or this is expected.
View 1 Replies View RelatedIs it possable to use rsa token on the ASA without setting up any other server just using the ASA, out clients use the cisco vpn client version 5.0.07.0290 and IOS 8.3(1), How would this be done?
View 3 Replies View RelatedI am trying to configure a SSL VPN on a Cisco ASA5520. Unfortunately the port 443 of the OUTSIDE interface of ASA is already in use by Microsoft Outlook Web Access and I cannot change the configuration of Outlook. This configuration already in place prevents me to use the public IP of the ASA as Cisco VPN ip address for the webpage. I don't either want to use a different port so to keep life easy for the users.I have some public IPs available that I can use so I wanted to use one of them instead of the ASA's OUTSIDE interface.
View 7 Replies View RelatedI have connected an ASA 5520 firewall DMZ to SERVER (17) vlan in core switch and INSIDE is connected as trunk to the core switch (including vlan 15,18). now the management ip of the switch is 10.xx.xx.126/25. and the other vlans are showing "administratively down"..but if I enter to any of the other vlans and do a "no shut", that particular vlan wil go UP but the other 2 will go down..means only one vlan become up at a time.
View 4 Replies View RelatedCan i use at one site ASA 5520 and another site Router to configure VTI tunnel with OSPF routing?
View 1 Replies View RelatedI have an iPAD. It connects to my ASA5520 via IPSEC. When it connects it gets an IP address from the ASA but it does not get any of the other stuff. Specifically the DNS suffix. How to correct it?
View 3 Replies View RelatedI'm trying to setup a tunnel from our Cisco 5520 to a 5550 using one of our external ips natted through this tunnel. For some reason traffic that should hit this tunnel goes through global nat. Here is the configs I have for this tunnel:
access-list policy-nat extended permit ip host 66.77.88.170 host 1.2.3.4
access-list Outside_cryptomap_60 extended permit ip inside-network 255.255.254.0 host 1.2.3.4
access-list Outside_cryptomap_60 extended permit ip host 66.85.99.170 host 1.2.3.4
[code]...
If I ping 1.2.3.4 from a inside ip host I see in the logs that it uses 66.77.88.136 as the NAT and not 66.77.88.170. Do you see something wrong with this configuration?
I'm currently running 8.3(2) on my 5520s in an active/standby config. The 5520s have the 2GB RAM upgrade and 256MB flash card. Are there any CPU limitations in going to 8.4? I read the release notes but didn't seen anything about CPU. I heard through the grapevine that a 64-bit processor may be needed. We currently have the Pentium 4 Celeron 2000 MHz CPU.
View 1 Replies View RelatedI have connected an ASA 5520 firewall DMZ to SERVER (55) vlan in core switch and INSIDE is connected as trunk to the core switch (including vlan 66,77). now the management ip of the switch is 10.xx.xx.126/25. and the other vlans are showing "administratively down"..but if I enter to any of the other vlans and do a "no shut", that particular vlan wil go UP but the other 2 will go down..means only one vlan become up at a time.
View 1 Replies View RelatedI have a 5520 VPN that is otherwise correctly configured for access (so I would say). It is in test (external IP x.x.x.10/22) running parallel on an external switch to a Check Point (x.x.x.4/22) that is the live setup.
I can tunnel consistently to the outside interface on its external IP from inside the network, which is probably natural since I'm inside the network making the attempt; however...
When attempting connection from somewhere outside the network, I generally do not get response from the device. If I connect/disconnect from the Check Point VPN first, then I can subsequently get a connection to the ASA. I did actually have one instance of non-massaged connectivity to the ASA, but there was nothing that I did in the configs that would allow me to claim credit for that instance.
So here's the question: Is there a timeout setting that makes the outside interface go to sleep or something? I'm still at the developmental stage where settings that would be obvious trip me up for hours. I verified the routes. the timeout configs are below; I believe they are all default..
arp timeout 14400
!
timeout xlate 3:00:00timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolutetimeout tcp-proxy-reassembly 0:01:00
I have setup IPsec remote vpn users into the Cisco ASA 5520 using Radius into my main network. Works just fine. I have site to site tunnels from my Cisco ASA5520 going to other sites, some of the tunnels have Cisco ASA and some have SonicWalls. I would like my IPSec remote VPN users to be able to traverse into those site to site tunnels to access the remote subnets attached to those tunnels. Do I need to use a combination of routing and ACL's? Or do I just use ACL's only? Or do I just use routing only?
View 2 Replies View RelatedWhen I try to put my ASAs in active/standby config here is the error I get.Warning: Failover message decryption failure. Pleas make sure both units have the same failover shared key and crypto license or the system is out of memory.
View 1 Replies View RelatedI configured dual ISP on ASA 5520 following cisco doc below. Now I would like to configure SSL VPN to work with this for failover? I tried to find an article regarding this but I could not. [URL]
View 3 Replies View RelatedIve got a customer asking for 2 products to be installed on an ASA 5520?
ASA 5500 SSL VPN 10 Premium User License and AnyConnect Essentials VPN License - ASA 5520 (750 Users)?
Am i correct in saying only one of those licences will actually be active at any time?