Currently I have a IPSEC VPN access to the PIX 515E using UDP, how to setup the PIX with IPSEC over TCP?
The OS version I am using is Cisco PIX Firewall Version 6.3(5)
I cannot type in command like isakmp ipsec-over-tcp port 10000Does it mean IPsec over TCP is not supported in this version?
We have set up a site to site IPSEC VPN between a Pix 515E running 8.0 (4) and an 1841 using static IP addresses at both ends. We used CCP on the router and ASDM on the pix to build the initial tunnels. Now the site with the router is changing to a Dynamic IP address from the ISP so we have set up Dynamic DNS to update the dynamic IP address.
The problem we have is that ASDM will not allow us to set a domain as the peer address, it will only accept an IP address. We think the solution will be to remove the static Crypto Map and replace with a Dynamic Crypto map on the Pix side. Our questions are simply; is this the best solution? can we edit the original static list or is it better to delete and make a new dynamic crypto map? Is there a short cut to change the config in command line? This is a live network so just want to check before we make changes on live kit.
I have a PIX-515E version 8.0(2).I have two remote sites connected to this PIX via IPSec tunnels.Each remote site can reach the local networks behind the PIX but I can not reach remoteSiteA from remoteSiteB.So,
10.30.8.254 SiteA <----- IPSec -----> PIX1 <----------------> SiteX 10.0.8.1
10.138.34.21 SiteB <----- IPSec -----> PIX1 <----------------> SiteX 10.0.8.1
SiteA can ping SiteX
SiteB can ping SiteX
SiteA can't ping SiteB
SiteB can't ping SiteA
If i do show crypto isakmp ipsec sa I can see appropriate subnets:
Crypto map tag: CRYPTO-MAP, seq num: 4, local addr: 203.166.1.1
access-list ACLVPN-TO_SITEA permit ip 10.138.34.16 255.255.255.240 host 10.30.8.254
local ident (addr/mask/prot/port): (10.138.34.16/255.255.255.240/0/0)
remote ident (addr/mask/prot/port): (10.30.8.254/255.255.255.255/0/0)
current_peer: 104.86.2.4
[code]....
Some log messages that seem to point to the problem...
Apr 18 2013 13:27:35: %PIX-4-402116: IPSEC: Received an ESP packet (SPI= 0xD51BB13A, sequence number= 0x21A) from 104.86.2.4 (user= 104.86.2.4) to 203.166.1.1. The decapsulated inner packet doesn't match the negotiated policy in the SA. The packet specifies its destination as 10.138.34.21, its source as 10.30.8.254, and its protocol as 6. The SA specifies its local proxy as 10.0.8.0/255.255.255.0/0/0 and its remote_proxy as 10.30.8.254/255.255.255.255/0/0
My question is really do I need to do anything funky to allow the traffic to pass between the two tunnels?
In my Cisco PIX-515E Version 6.3(5), I have a IPSec VPN tunnel and also to the same firewall home users connect through VPN client. I am unable to find a solution that allows my home users to connect to office network and again access the remote network through the IPSec tunnel.
View 1 Replies View RelatedI need to redo the configuration on the new one?
View 11 Replies View RelatedI tried any type of combination and just couldn't make it works. Only PPTP works well. Whether Apple iOS IPSec VPN is supported or not?
View 11 Replies View RelatedI have 2 Cisco Pix 515E. Both are on the same sub nets.Cisco1 has internal IP 10.0.0.1 and Cisco2 10.0.0.2. Internal servers have default gateway on Cisco1. When I establish VPN to Cisco2, connect to internal servers doesn't work due to routing.
When I set static route on servers to Cisco2 VPN pool with gateway 10.0.0.2 it works. Is it possibility to do it without static route?
I have the following network.2 WAN links termination on my PIX 515e and all internal users connected to third interface.
Problem I am facing is that I have assign manual IP to users with some have full access to Internet while others have limited.
The users are changing their IP address while others are offline and I want to restrict them.
The only way I can think off is by binding IP to MAC as e.g ( Active wall software). But can it be done on PIX 515e and if so how?
I have erased the Cisco image from my PIX 515E, and while i tried to load a new image its asking for activation key. I tried its old key. but no use.
View 1 Replies View RelatedI have recently migrated from a PIX 515e to an ASA 5510. In the main this was successful. However, I have a number of L2L VPN's (all connecting to Cisco PIX 501 or 505). The majority of these VPN's are working fine. However, I have a couple of VPN's that are causing me a problem. It seems like the tunnel is established for anything between 10 minutes and 4 hours before going 'down'. I cannot initiate the tunnel again from the hub end (ASA 5510) of the VPN.However, if the remote end reboots the PIX, the tunnel is re-established.The ASA is running 8.3(1) and the remote PIX's will be running various versions of code but will all be 6.3(x). The strange thing here is that the majority of the sites are working and the config for each tunnel is identical other than the access-lists for interesting traffic and peer address.
View 7 Replies View RelatedI am trying to setup a VPN tunnel between a PIX and an ASA. I went through the IPSec Site to site wizzard using the same settings but I cannot ping hosts from either side.
Here is the setup
ASA 5520
Device Manager 6.4(5)106
Software version 8.0(5)
Inside network 10.0.0.0/24
Inside IP 10.0.0.1
[code]....
I've just set up dialin VPN on my PIX 515e. The users can connect fine but my split tunnel ACL is not applied and I have the following error in syslog No translation group found for udp src outside:10.0.56.2/137 dst inside_lan:10.0.8.6/137 If i try to ping my inside interface from the client, i get a reply from the outside interface IP address. Do I need a specific NAT rule for my VPN client users?
View 2 Replies View RelatedI have a PIX 515 Ewhich does authentication for SSH via RADIUS protocol and fails over to the local database if radius server goes offline. But when the radius server comes back online, authentication still takes place through LOCAL and not the radius server. Following are the commands:
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
[Code].....
\I just configure my PIX 515E with version 7.0(4) and having problems to get traffic out on eth0 (if name outside). There is no problems between different VLAN ,all VLANs are configure on eth1. It is also possible to accass services on VLAN 10 (DMZ) from outside. The only thing I see in syslog is "Built Outbound" and "Teardown".
View 11 Replies View RelatedI have a Pix 515E running PixOS version 8.0.4 with two interfaces, inside and outside.On the inside interface, I have a Redhat Enterprise Linux 5.4 64 bits machine as an NFS server version 4 (NFSv4).On the outside interface, I have three (3) Redhat Enterprise Linux 5.4 64 bits as NFS clients.I am looking for the exact UDP and TCP ports to be added to the ACL in order to accomplish
View 1 Replies View RelatedI need ot upgrade a Cisco PIX 515 E to A Cisco ASA (not sure what type and modle yet!). the PIX currently has about 80 lines of ACLs and no VPNs. So only inside and outside interfaces and 80 lines of ACLs to be transferred over to the ASA.I was wondering if the ACLs can be transferred over to ASA as is?is there anything that I need ot watch for?
View 1 Replies View RelatedI have an issue in the Cisco PIx 515e series. The IOS is 6.1(2).I have set sepecific access-list to allow incoming traffic to inside interface. But still the TCP 3-way handshaking is dropped here. [code]
View 6 Replies View RelatedI have my PIX 515E (8.0(4)24) configured for VPN access. In the VPN configuration, I am using an RA tunnel group configured to use Windows 2003 IAS to authenticate users against active directory based on group membership and using a local IP pool for address assignment. This all works fine. I got a request from a single user to have a static IP assigned from the pool. I read that one way you can do this is to get into the user properties in Active Directory for the user and in the dial-in tab tick the box for 'Assign a static IP address' to have it give the particular user a static address for VPN, but it does not work. What I would like the PIX to do is assign addresses from the local pool unless there is an address assignment configuration in RADIUS. Basically does the PIX honor the IP assigned via RADIUS even if the tunnel group is configured for a local IP pool or do I need to configure the tunnel group to use AAA address assingment for the AD dial-in config to work at all? Does the PIX functions this way? I configured the user in AD for this but it does not work. I also have the no vpn-addr-assign aaa command enabled in there which might be the whole issue. I will try to change this in the next window and see if it flies then. Just wanted to see if the PIX works this way or if I am way off here.
View 5 Replies View RelatedWhat would be the access-list entry to allow protocol 97? I am setting up foreign-anchor controller and need to allow protocol 97.
View 1 Replies View RelatedI need to configure a Cisco pix 515e as vpn concentrator. Now the network has 2 Cisco pix in fail over - May I add a new Cisco pix in parallel and redirect the vpn tunnel on it? How do I need to make the configuration in order to work?
View 2 Replies View RelatedI have a cisco 515e pix but where I bought it from did not get the machine back to default. I boot it up and get to the user prompt, type enable and it asks for a username and then a password. I am new to this and am have no problems with router and switch password recoverys but when I look at the cisco documentation it is a bit overwhelming and I am not quite sure what it is that they want me to do to fix this. I have downloaded all the password recovery software loads and have the one I need for 6.x which is what the box is running I am just not sure what it is that I need to do. Can I use that recovery software from directly from my pc using a tftp server?
View 1 Replies View RelatedWe just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
View 8 Replies View RelatedI'm trying to use port redirection to allow outside access to a internal web server. As far as I can see, everything is configured properly. The Open Port Checker tool from yougotsingle.com says that the port (80) is open. However when I goto access it the connection times out. The external address is static from my ISP, and I will call it xxx.xxx.xxx.xxx. The server is at 10.1.1.20, and is functioning properly over the LAN.
View 7 Replies View RelatedI have Cisco PIX 515E for my Lab and can't recover the password. It is not connected to the network. I have configured server, address, gateway from the monitor mode and tftp not seeing my laptop. best way to reset or recover password.
View 7 Replies View RelatedI have pix 515e locate in office w/ IPSec VPN service ,that just for out of Office to access email
I wanna know how to config the VPN user thru the office Internet to access the web
Such I'm in china to access Facebook while I connected the VPN
I've been struggling to get ASDM (PDM) installed and running on my PIX 515e. The PIX IOS version is 7.2.4(30) The ASDM version I've copied to flash is 524.
I've followed the Cisco documentation verbatim, however I still cannot connect via the Java ASDM client or via http. When I try to connect via http, my PIX shows the following error: "tcp access denied by acl from..." I do not this this is a security (ACL) issue as I've tested after opening everything up and still no luck.
Here's my running config (w/ the relevant statements prepended with ">>>"):
show run
: Saved
:
[Code]....
I've got a PIX 515e firewall on a branch site running version 7.2.4.7(LD) connecting via a VPN to an ASA at the HQ with 7.2.5 code running. After several hours it is no longer possible to ping either the PIX or hosts behind it on the branch LAN though the tunnel still shows as being up. In order to bring the link back up the local PIX has to be rebooted.The connection used to work with no problems when I was running PIX version 7.2.1 software but this had to be upgraded to 7.2.4 to support the new TCP normalization commands. VPN connections to other branch sites running PIX 7.2.1 remain active with no problems. The reason for the upgrade is to implement WAN acceleration between the sites however I still encounter this problem even when the WAN acceleration hosts are not installed.In addition to the software upgrade I added the following configuration to both the ASA and the PIX:
tcp-map wanx_tcpmap
synack-data allow
invalid-ack allow
seq-past-window allow
tcp-options range 28 28 allow
[code]....
The ASA originally had this code but the PIX did not and the VPN was stable, after upgrading the PIX and adding the code the link was no longer stable.
I have the following Pix 515E Firewall, that has been working good for a few years. But suddenly, the Pix stop booting up. The only thing that is happening is the power and network traffic led flashes and the active led is off. So my question is that is this symptom a hardware or software problem and is it fixable with either new parts; or is my firewall dead. I suspect that it is a hardware problem since the active led doesn't light up. I cann't even enter the ROM Moniter mode.
View 7 Replies View RelatedWhat would be the command to clear the df-bit on a PIX-515e running 6.3? I have tried the following:
conf t crypto ipsec df-bit clear-df inside and it doesn't take it.
I am facing high CPU util on my pix 515 E which is in failover mode.During peak hours the util is see rising to 60% where as in off peak hours it is normally12%.
During normal operation the average utilisation was observed to be 30% but suddenly from 2/3 days it is constantly 60% doule the value as earlier. Have gone through the logs and traffic but not able to tarce anything particular
below is the o/p of some command taken for analysis
IOS version 8.0(4)
sh cpu usage
CPU utilization for 5 seconds = 51%; 1 minute: 61%; 5 minutes: 58%
sh cpu usage
[Code]......
I need to create a DMZ zone in my network. One server need to be put in DMZ. I have a PIX 515E 6.3.3. It has free port to create DMZ.
1) Put a new switch for DMZ zone
2) Connect it to the DMZ port
3) Create a NAT for inside to DMZ with same IP as inside
4) Create ACL for permiting traffic to DMZ and apply it to outside interface
5) Create ACl for permitting traffic from DMZ to inside
6) Routing for DMZ in PIX
I am trying to change the DNS server that my VPN gives to VPN clients on a Cisco PIX 515E. What command will change it from 10.6.0.2 to 10.6.0.4? The software version is 7.2(3)
View 3 Replies View RelatedLooking at migrating from the following:
PIX-515EPIX Security Appliance Software Version 8.0(4)Device Manager Version 6.1(5)51
to
ASA5515Cisco Adaptive Security Appliance Software Version 8.6(1)Device Manager Version 6.6(1)
Is this migration directly supported, or do I need to downgrade first?