user from home PC via Anyconnect making RDP session to work PC, on this PC Microsoft policy allow making disk mappind via RDP. Is that posible to inspect this traffic and deny this(disk mapping) action on ASA5585-X with IPS?
View 1 Repliesip inspect firewall should be performing no inspection on traffic traversing an IPSec VPN right?
View 2 Replies View Relatedim in the progress of Configuring a Cisco 881 Router, for a branch office.Behind this Router they have an PBX, is it prossible to inspect SIP packet using CBAC, and thereby open for RSTP pinholes.i only have 1 Public ip adresser, and im not fond of configuring thousands of PAT to the PBX.i have with success, Accomplished this with Global Inspection on ASA Firewalls, but i dont know if this can be done with IOS as well.
View 5 Replies View RelatedI have a cisco ASA5520 box running with IOS version8.2(5)13 where default policy map is applied globally. But I have not seen any traffic being inspected through included protocol defined under policy map.All configuration seems to be ok for me.
service-policy global_policy global
Global policy:
Service-policy: global_policy
Class-map: inspection_default
Inspect: ftp, packet 0, drop 0, reset-drop 0
[code]....
I have a need to use a 3560 switch to terminate a provider's internet connection, but want to secure it so that it and the vlans connected to it are not wide open. At the same time, I'd like to use stateful packet inspection.
I have IOS 12.2(44)SE2, but IPBASE running on my 3560s. Is there an IOS (perhaps the ADVIPSERVICES of that version?) that allows a 3560 to use the 'ip inspect' command?
we just purchased 2 asa 5585-40's and tried to add them to our lms 3.2 system and we were informed by cisco tac that they were not supported in lms 3.2. since we don't having funding for an upgrade, any work around within lms that could allow me to add the devices so i can use lms for syslog and to fetch the firewall configs on a regular basis, instead of having to setup a seperate syslog server and having to tftp the config's everytime i make a change.
View 3 Replies View RelatedI have put 2 physicl interfaces (te0/8 & 9) on the ASA-5585 into a PO and am assigning ips/vlans to the sub-interfaces. I have 2 issues: - Why am I not able to ping the other sub-interface from the ASA itself? (I can ping the 1st one), Secondly, why the IPs are not visible in "sh int ip brief" ?Although I can see them in "sh ip" ..
/actNoFailover(config-if)# int po17.100
/actNoFailover(config-subif)# vlan 100
/actNoFailover(config-subif)# ip add
[Code]....
how to enable inspect http on ASA 5510, so that URL information populate in the syslogs?
View 2 Replies View RelatedASA5510, ASA 8.0(4), ASDM 6.1(5), this is a productino ASA with plenty of lookups working through its 3 interfaces - outside, inside, dmz. The problem is a new use. I've segmented a switch on the inside network with a VLAN, and have a workstation routing through the switch to the default VLAN where all other hosts on the inside network reside so far. The ASA inside interface is the default gateway for the inside network. My test worksttion can PING inside hosts, so the static route is OK.
ASA 10.1.1.2/16 DNS Server 10.1.5.1/16
| |
------------------------------------------------------------------
|
Switch 10.1.8.20/16
[code]....
But lookups fail, Wireshark says the test workstation sends, the dns server receives and responds, but the test workstation never receives. I used the Packet Tracer tool, it gets to the last step syayin OK then finally "inspect-dns-invalid-pak". I can't find any more there to tell just what is invlid about it. So I'm trying to figure out global inspection. Here's an extract from the config:
class-map inspection_default
match default-inspection-traffic
!
!
policy-map global_policy
class inspection_default
[code]....
I've been trying to figure this out for some time now. I have a network setup with a couple of users, as well as a few servers. I'm using a 3640 as my border router that is connected to a 3750 with L3 routing enabled. I am using the IOS firewall in the 3640 and am having problems with downloads and connections in general on the LAN. Downloads will start at fast speeds (~1MB/s) but after a short time, it will begin slowing to a crawl or idle. I have disabled my ip inspect rules and found that the downloads will function at full speed for the entire download.
I've looked over the router configs several times, and I don't see anything unusual. Is there anything I should be looking for? I would like to think that this router can handle the traffic of about 5 computers.
I've read through netpro and found everyone points to this doc.
[url]....
However that still doesnt allow traceroute through for us. We still see syslogs with deny's on high level random UDP ports to different Internet destinations.
[code]....
I got some issues with my CISCO ASA, the thing is that when I add a new rule on the device this rule duplicate and goes to the bottom. We already tried to delete the duplicate rule but it always show an error.
-Model 5585
-ASA Version: 8.2(5)
-ASDM version: 6.4(5)
I have two questions about ZBF on ASR1000 with Firewall and Flexible Packet Inspection license:
1 is IPv6 supported?
2 can I use police action in an inspect rule? I want to limit some protocols to low bandwidth. There is no police command in ZBF policy map.
I want to block some social networking sites using ASA 5510-CSC-SSM, As I searched and come to know that ASA 5510 can't inspect and intercept for https traffic because it is encrypted while traversing throught the ASA. I want the ASA to make functioning for https too, not only http. Can i perform this task by updating any software on existing device?
View 2 Replies View RelatedI have a strange problem in my ASA 5510 firewall. I turned on HTTP inspect policy to block certain URLs, but that destroyed svn communication. Interestingly, if I use simple web-browser to access svn server - it works, but any svn-client requests fail with an error "Could not read status line: An existing connection was forcibly closed by the remote host". I did some packet sniffing, and discovered that with HTTP inspect off the Webbed request is answered, but with HTTP inspect on it is rejected with an error unauthorized. Here are examples of success and failed conversation packets:
Success:
1. <Client-IP> <Server-IP> WEBDAV WEBDAV:Request, PROPFIND /svn/repos/myrepo/trunk {HTTP:3, TCP:2, IPv4:1}
2. <Client-IP> <Server-IP> WEBDAV WEBDAV:HTTP Payload, URL: /svn/repos/myrepo/trunk {HTTP:3, TCP:2, IPv4:1}
3. <Server-IP> <Client-IP> TCP TCP:Flags=...A...., SrcPort=HTTP(80), DstPort=58882, PayloadLen=0, Seq=4139355337, Ack=3464798063, Win=258 (scale factor 0x8) = 66048 {TCP:2, IPv4:1}
4. <Server-IP> <Client-IP> WEBDAV WEBDAV:Response, HTTP/1.1, Status: UNHANDLED HTTP Status Code, URL: /svn/repos/myrepo/trunk {HTTP:3, TCP:2, IPv4:1}
Failure:
1. <Client-IP> <Server-IP> WEBDAV WEBDAV:Request, PROPFIND /svn/repos/myrepo/trunk {HTTP:3, TCP:2, IPv4:1}
2. <Client-IP> <Server-IP> WEBDAV WEBDAV:HTTP Payload, URL: /svn/repos/myrepo/trunk {HTTP:3, TCP:2, IPv4:1}
3. <Server-IP> <Client-IP> TCP TCP:Flags=...A.R.., SrcPort=HTTP(80), DstPort=1137, PayloadLen=0, Seq=1075661931, Ack=4049054406, Win=64240 (scale factor 0x0) = 64240 {TCP:2, IPv4:1}
4. <Client-IP> <Server-IP> TCP TCP:Flags=......S., SrcPort=1138, DstPort=HTTP(80), PayloadLen=0, Seq=1032908784, Ack=0, Win=64240 ( ) = 64240 {TCP:4, IPv4:1}
5. <Server-IP> <Client-IP> TCP TCP:Flags=...A..S., SrcPort=HTTP(80), DstPort=1138, PayloadLen=0, Seq=4184445498, Ack=1032908785, Win=8192 ( Scale factor not supported ) = 8192 {TCP:4, IPv4:1}
6. <Client-IP> <Server-IP> TCP TCP:Flags=...A...., SrcPort=1138, DstPort=HTTP(80), PayloadLen=0, Seq=1032908785, Ack=4184445499, Win=64240 (scale factor 0x0) = 64240 {TCP:4, IPv4:1}
Packet # 4 is an actual differentiators.
I found one mentioning of that error with that assessment: "Older firewall/proxies do not understand the Webbed related HTTP requests for accessing Subversion using HTTP{ URL} in that post But not any useful tips.
I am trying to configure my ASA 7.2(4) to inspect SCCP traffic from a CUCM v7.I have been advised that the ASA device needs to support the version of Skinny I am running.What version of Skinny does ASA 7.2(4) support? How can I find out what version my phones are using?
View 3 Replies View Relatedi am wanting to log dropped and oop packets on a c3825 isr with ios12.3(11)T3. on other routers(like a 2951 running 151-4.M2)i can state ip inspect log drop-pkt and it will log to buffer or syslog all dropped and oop packets. can i do this on this 3825 another way
View 1 Replies View RelatedWe are currently looking at design models for a Multi-Tenancy solution.The firewall layer will be 2 X ASA's running 9.X to take advantage of VPN's in multiple context mode and mixed L3 and L2 contexts.
We will be delivering services through multiple L3 contexts (between 2 and 5 L3 contexts for services) and 1 transparent context for customers infrastructure who will then have virtual firewalls for NAT's and VPN's etc withing their own environment.
I am not very experienced with IPS so my query is; if we were to get an IPS license for both ASA's how would the IPS fit in, can we use it to inspect traffic for all the L3 contexts and the transparent context?
We saw this syslog on ASA5585 with version 8.4(1). I have two HA firewall pairs (contains 4 ASA5585, active/standby), and I saw this message on the standby ones.
Jun 7 07:36:26 10.99.96.32 last message repeated 4 times
Jun 7 07:36:26 10.99.96.32 :Jun 07 07:36:26 HKST: %ASA-ha-3-210005: LU allocate connection failed
[Code]....
I have ASA5585 Firewall between my WAN Cloud and LAN Network. I plan to configure Layer 3 Vlan Interfaces inside FW and it would be Layer 3 gateway for some of Subnets. Layer 3 VLAN Interfaces are planned to be dual stack containing both IPv4 and IPv6 Address stack.
I plan to configure 6 to 4 Tunnel with my Hub Site where we have native Ipv6 awareness. One tunnel end point would be ASA and the other endpoint would be Hub site WAN Router/L3 Switch. So IPv6 traffic hitting to vlan interfaces on ASA would be policy checked and routed over tunnel interface to Hub Site.
6to4 Tunnel manual tunnel configuration on ASA. I have configured such tunnel on L3 Switch or Router with following config.
Int tunnel xyz
ipv6 address <ipv6 address>
ipv6 enable
tunnel source <loopback address of my L3 Switch>
tunnel destination <loopback address of my hus site L3 Switch/Router>
tunnel mode ipv6ip
end
I need to implement something similar in ASA. How can I do that?
How do i measure the total throughput going via 5585-X.It has the firewall througput of 5Gbps. Looking at aggregate of all the interfaces traffic going through it seems about 4gbps is going through.
I use show traffic command and add up the trasmit and receive traffic on each live interface.Is that correct method and are there any more commands?
I have 2 ASA 5510 firewalls at 2 different sites. Both running on version 8.0.4. Users are using an Instant Messaging type of application provided by a local telco here which is able to send and receive SMS using SIP (from the packet capture that I've done).
When users use the IM in site A, they are able to send and receive text messages via the IM from behind the firewall. However, when the users are in site B, users are able to send out text messages but not able to receive them.
I noticed that when I remove "inspect sip" from site-B's global policy map, users from site-B can successfully receive text messages. I have confirmed that it is the firewall that drops the packets as I have captured the inside and outside interfaces of site-B's ASA and I can see the incoming sip "request: MESSAGE" packet on the outside interface but I do not see the packet exiting the inside interface.
I have cross check both firewall configurations, and I do not see anything suspicious commands relating to sip that might cause this issue. Is there any command to troubleshoot why the sip inspection is dropping the sip packets on site-B?
use of a pair of ASA 5585's in active/active mode with a shared outside interface.Last time I did this was with FWSM, there was a restriction where all contexts that share an outside interface have to be in the same failover group.Does this apply also to the ASA? My thought is that it will, but I am unable to find that in any documentation.
View 1 Replies View RelatedWe're currently PATing everything from a particular subnet to the IP of an outside interface using our ASA5585 (dynamic PAT). We're experiencing pool exhaustion and therefore need to expand the global IP range. Any way of cutting over to the new range without dropping existing connections? For clarity, the current interface address is x.x.x.37/22 and the new PAT pool is x.x.x.114-6/22.
View 6 Replies View RelatedRunning ASA5585’s in active/standby across a local campus MPLS network. Supported design, leading practice etc. Specifically our design is that two ASA5585 are configured as active/standby through a local campus MPLS network over 10gig links through ASR9k etc. The ASA’s are providing inter-vrf routing capability only with p2p l2vpn circuits configured for each logical interface between the ASA over MPLS etc.The failover link is via a direct fibre and the state link will be through a p2p l2vpn (option for direct fibre also)Is this a supported design to begin with?
View 2 Replies View RelatedI have a ASA5585 running 8.4 that is redirecting Internet http to a websense server via GRE.The integration is working fine, except when a user PC sends a large packet (~1500 bytes).With WCCP/GRE headers, the user packet is too large to be transmitted to websense, so the ASA fragments the packet in two and transmits both to websense.
A sniffer trace confirms that both fragments reach the websense server, but the TCP packet is never acknowledged.User-side TCP retransmits the large packet three times over 15 seconds, and eventually retransmits fine with smaller packets. The 15 second delay is of course not acceptable.Users and Websense server are both on the Inside interface.
We are considering imposing browser proxy to websense (which works fine), but would prefer not, considering the increasing diversity of devices.
We are experiencing intermittent issues with the IPS on our ASA5585 vs 8.4(2). Probably something with the dataplane. So I want to keep debug cplane 255 activated and logged with log debug-trace setting to syslog server. But when session times out the debug command is cleared so the output stops. Since it is a intermittent issue I want to keep debug activated...Totally different behaviour then with routers which keeps it activated. how to keep debug activated on a ASA.
View 1 Replies View RelatedI have seen this a couple of times on two different routers. One is a 3745 and another a 1811 running 12.4(15)T4 and 12.4(6)T11, respectively.
When we have IOS firewall running (either IP inspect or ZFW), we will experience intermittent slow HTTP connections.
Symptoms include page timeouts, CSS not loading and just overall slow performance. Disabling the inspection cures the issues.
I have two ASA in failover with Active/standby configuration. When I switch from standby to active from the standby ASA I get a lot (like 100) of error messages like these below: [code] The failover works fine and nothing seems to be wrong with the firewalls function.
-Hardware is ASA5585-SSP-10.
-Software version: ASA 8.2(5),
ASA is in multiple mode with 17 active context. Why these error messages appear and what they mean?
We have pair of ASA5585 (ver 8.4(4) with IPS module configured with Active/Standby failover. There are total 09 interfaces are connecting to different zones in the firewall and out of which three(3) interfaces are connecting to Palo Alto 2nd layer firewall. When we test the failover whatever interfaces not connecting Palo Alto failed or shutdown, ASA triggers the failover to other unit, however the Palo Alto is not detecting this failover and it still keeps its previous Active Palo Alto to pass traffic, thereby failing passing traffic on Active firewall through Standby Palo Alto firewall.
But when there's a interface failed or shutdonw on the interfaces where PaloAlto also connected, then once the ASA failover triggers and the same time Palo Alto also trigger its failover then both new active firewall and Palo Alto sending traffic through firewall.However we we cant all the interfaces of ASA also to connect Palo Alto and let the Palo Alto to inspect all the interfaces, but we need our ASA to work in a situation where any of the interfaces failed, the failover to work smooth the pass the traffic via either Palo Alto device.I just need to know is there anything tricky that we can configure on our ASA in this failover senario, or to confirm if there's no any workable solution to this situation.
I have attached the senario that I explained above. Just to emphasis the issue again, if any interface of Gig0/0, Gig0/4 or Gig0/5 failed on active firewall, ASA switching to standby firewall and act as Active, but Palo Alto still remains his Active state and the new Active ASA is not passing traffic via standby PA as its not detecting any of its interfaces as failed or unreachable..?
WE have to deploy ASA5585 in between User vlans & server vlans. we have to find all the ports that needs to be opened on firewall. any tools to do same.
View 2 Replies View RelatedI am interesting how ASA 5585-X with SSP-60 operates in dual firewall mode, if I install two SSP-60 modules in chassi, do I get one logical firewall with doubled performance of (SSP-60) ?
View 1 Replies View Relatedits possible to set up active/active failover using etherchannel on 5585s?
View 1 Replies View Related