I'm trying to set the tcl source to the flash card on an 1861 router with the following command; TestBox(tcl)#source flash:101.tcl and I get the following message; couldn't read file "flash:101.tcl": File not found.I've copied the file to the flash card by putting the cf in my pc and just dragging it there. What's the proper syntax to set source to flash? I've tried flash0 and flash1 with the same result.
View 9 RepliesI have a really stupid problem with my RV042. The main logon password has expired but it will not let me change it at all. Basically I try to login but get the error 'The old password has expired. Please change the password'. But with no prompt at all for a new password and just a return to the login page. Tried various different browsers, tried the old default password but nothing will work. There seems to be no way of changing it and I cannot login.Am I missing something glaringly obvious? I really don't want to reset it to default as I have numerous VPN tunnels configured and various other settings.
View 2 Replies View RelatedI have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error. [code]
View 3 Replies View RelatedEvery time I delete the directory flash and reinstall it, I get an error:
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin"
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin" Interrupt within 5 seconds to abort boot process.
That is the message I get. It's set to NO manual boot, but it keeps making me manually boot it. I am at a loss, I've done 3 switches and they all keep doing the same thing.
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error.I saw that this can be fixed with
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#no service config
Switch(config)#exit
Switch#
00:13:47: %SYS-5-CONFIG_I: Configured from console by console
Switch#reload
I have done this 3 times to no avail.My TFTPd32 server on my pc is working fine.Here is the error
Switch#sh flas
Directory of flash:/
2 -rwx 556 Mar 1 1993 00:33:53 +00:00 vlan.dat
4 -rwx 3775 Mar 1 1993 00:37:54 +00:00 config.text
5 -rwx 24 Mar 1 1993 00:37:54 +00:00 private-config.text
6 -rwx 5687963 Mar 16 2007 01:05:23 +00:00 c3550-ipbasek9-mz.122-25.SEB4.bin
8 drwx 192 Mar 1 1993 00:04:40 +00:00 c3550-i9q3l2-mz.121-22.EA1a
[code]......
I recently posted this same issue the other day, using TFTPd32. Now i am pretty close to fixing it. I do have a different setup; my pc ethernet port is broken so I am using an ethernet/usb adapter. I am attempting to backup my IOS from a 3550 switch to my PC.
This is the error I am getting. Code...
I have Cisco 2800 series router. When I am trying to write memory getting error message " Error opening flash:config-backup-1 (No more root directory entries available)" When there is simultaneous access to a router's NVRAM, we might encounter these errors. In order to clear the line the other user(s) is (are) connected on and free the NVRAM, issue the clear line command. But still getting the same error message.
View 1 Replies View Relatedif the card HWIC-1SER is the equivalent card HWIC-1T for 1861 router?
View 3 Replies View RelatedTrying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
My Router is showing like this can any one explain me what it is and why its showing like this and every time its going to Roman mode some times going to Normal mode how to trouble shoot this problem, is the problem is flash or some thing else explain me and why its showing like this (Read only Roman initialized)
The output is shown like this
System Bootstrap, Version 12.4(11r)XW3, RELEASE SOFTWARE (fc1)
Technical Support: { URL}
C1860 series platform with 262144 K bytes of main memory
Read only Roman initialized
program load complete, entry point: 0x80015000, size: 0xb700
program load complete, entry point: 0x80015000, size: 0xb700
[ code]....
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 7Mb.
adjusted iome size up to minimum size of: 0X00C00000
Using 4 percent iomem. [12Mb/256Mb]
Bad FIO_0 EC220 vendor device id 0xFFFFFFFF
04:34:37 UTC Sat Apr 7 2012: Unexpected exception to CPU: vector 200, PC = 0x80444C24, LR = 0x80444C08
-Traceback= 0x80444C24 0x80444C08 0x80439DA0 0x80437BE0 0x800379F8 0x825B289C 0x810F8858 0x810F8B4C 0x80227A6C 0x8022A36C
CPU Register Context:
MSR = 0x00049030 CR = 0x22008084 CTR = 0x00000000 XER = 0x20000000
R0 = 0x00000000 R1 = 0x84CAE0C0 R2 = 0xFFF5FFF5 R3 = 0x00001388
R4 = 0x00000000 R5 = 0x84FAE234 R6 = 0x00000F9F R7 = 0x001312D0
[code]....
Configuring a Cisco 1130 AP (autonomous) to a 1861 router.
I am struggling to work out how to connect this and get it working.
Router has 2 v lans, VOICE and DATA. All switch ports configured for access v lan (DATA) and voice v lan (VOICE)
We need the AP to have an SSID for VOICE and DATA and the gateway/DHCP server for each of these to be the router.
I have not been able to find the option to turn on LLDP for our Polycom (Lync) Phones. Is this not an option for this model router (C1861)?
View 1 Replies View RelatedEarlier today I was attempting to do something with my router settings and ended up reading on the internet that I needed to do a hard reset to access my router interface - when I typed in the IP address, it came to a "could not find server" error in the browser. After doing the hard reset (holding down the reset button for 30 seconds) I was able to access the router, and adjust the settings. After doing this though I was no longer able to connect to the internet through the router, although the router is sending out a signal (it says connected to linksys but "no internet connection"). I am currently connected directly to the modem right now using my laptop.
Additional Information:
Router model: WRT45G v.3
ISP: Bellsouth
TL;DR: Did a hard reset on my router, now it's sending out a signal, but no internet. Modem still has internet, as does the router, (the internet button is green).
having a very strange problem with a Cisco 1861 running - Cisco IOS Software, C1861 Software (C1861-ADVENTERPRISEK9-M), Version 12.4(24)T5
I have suddenly started to get performance issues with downloads and access through the ZBF. Without the firewall enabled and just having NAT enabled and routing , downloads perform as expected - ( have been using Itunes download as test file ) - with the ZBF enabled , and the necessary rules installed to inspect & allow traffic - downloads stall - and the only way to get the downlaod to start again is to pause , then resume. The stalls are anything between the first 25 - 120 secs.
I have debugged and performed packet traces - but cant see anything untoward. I have also placed another router ( just a cheap Belkin ) on the ADSL service and again , the downloads work as expected.
one further thing to add is that when im tunneling through the firewall ( VPN ) , then downloads do work as expected - suggesting that the issue is with native HTTP(s) traffic..I have upgraded from T4 to T5 - and the symptons still remain - I am thinking that these may have been introduced when i upgraded to T4 a few monthes ago.
I am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies View RelatedI have a nat statement to nat a subnet to a host address. Only the host address is allowed to traverse the VPN. However when I use a route map to do this, I cannot see NAT being performed and my VPN does not come up. When I use a static NAT for a 1 to 1 host translation I can see nat being performed and the VPN comes up. Using the route map method, the other party said our source IP is 0.0.0.0 0.0.0.0.
View 6 Replies View RelatedI have a situation which requires some non best practice stuff to be done. There is a box behind an ASA that has a lot of code that references public DNS names and therefore needs access to itself and a number of other boxes on the same subnet via the public DNS names (that obviously resolve to public IPs). This traffic is dropped on some pretty fundamental ASA characteristics.I know this isn't really ideal, and it should be handled by DNS nstead, but I'm in somewhat of a bind and need to know if the ASA can allow this traffic.I figure I could match the traffic and exempt it from state-checking and that would probably work, but it's not a very graceful solution.
View 2 Replies View Relatedwhy the command "source cpu rp" has been removed from IOS15.0(1)SY1. I can succesfully configure the following ERSPAN on 12.2 SXJ3 but not on ios 15.x. Did not understand why cisco has descoped this command.
monitor session 10 type erspan-source
shutdown
source cpu rp rx (--- 15.0 has no such option on 6500 )
destination
[code]....
I have configured my Cisco 881 and it is quite stable but now I am working on some minor details.
I have several Public WAN IP addresses which are NATing to internal web server. When I go to the WAN IP at port 80 from the Internet, the NAT works fine and it maps perfectly to the internal Web server. However, when I try the same same WAN IP from the LAN which contains the web server, the Router blocks the traffic and I get nothing back.
I have verified that I can get to the Inernet from the LAN but it seems that I cannot go bfrom the LAN to the Internet and back into the LAN via NAT.
we use the latest LMS version (4.2.2). Under Monitor->Performance Settings->IPSLA->Devices i see all devices. When creating a IPSLA collector not all devices are listed in the source section but in the target section. Why is this happening?
View 2 Replies View RelatedI need to change the source IP of a packet for one of my NAT's.I currently have an Cisco 1812.I have an PPPoE connection as Dialer 0.I have another VLAN that is connected to an Netscreen SSG5 VPN gateway via another Cisco switch.I have a vlan trunk between the switch and the 1812. What I would like to achive is the following :-For any traffic going to the following three ranges make it apear as if it was coming from the VLAN50 address [code]I can ping my netscreen on 10.27.30.255 fine from the Cisco 1812. But any other PC fails, as for some reasion the traffic has a source of my Dialer 0 interface.How can I write a nat to change the source just for the tree destitnations ?
View 7 Replies View RelatedThe router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
I have been trawling the interenet looking for an answer to the i but to no avail.Can you change the source port that windows uses when it makes a connection to another host.
[code]...
i have issue with whenever i m trying to download any file it's get upto almost 95-98%,but after suddenly stop.this issue with firefox, chrome browser
View 1 Replies View RelatedEvery year I attend a local motorsport event and I am usually responsible for providing a live online video broadcast of the event which I do using a website such as ustream.tv or similar. The event is non-profit so spending as little money as possible or none at all is the best option for us. We use a 3G card/dongle and a laptop with 2 or 3 webcams for the video feed....The results/scoring system in use at the event is controlled by the organisers and they have setup a VNC server where teams can connect with their laptops via a wireless network to view results, what I would like to do, is to include the results screen in my video feed. So somehow, I need to trick my computer into thinking that the VNC viewer software is a video input device.I have looked for something similar last year but didn't have much success, If separate laptops are needed, I have 3 windows laptops at my disposal and a macbook pro which will be on the same network. Whichever one will be most suitable for the task will be used.
View 2 Replies View RelatedI have router which has two physical interfaces Gi0/0 and Gi0/1. G0/0 connects to metro over ethernet and Gi0/1 is configured a s router on a stick, which has many defined. All those interfaces have IP addresses assigned. EIGRP is configured between other metro sites. Here is a sample IP assigment for this site, let's say Site.
View 3 Replies View RelatedSome network pros have setup our Cisco 3620 many years back during implementation.
I've just added a new server, with new ip, wanted to change the ip of ip nat translation in this router.
I did a show run, the config is this;
interface FastEthernet0/0
ip address 57.31.132.116 255.255.255.240
no ip redirects
[Code]......
I have an 1811 with 2 WAN connections, Fiber and ADSL (both Ethernet). I'm having a heck of a time getting traffic out the ADSL link.As it stands, I can ping the next hop 75.158.58.1, but no further. ping source FastEthernet1 times out to any external address nor can I NAT internal subnets out the interface.I'm really at a loss as to why, especially since I can ping
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
[code]...
I have a internal subnet 192.168.3.0/24 sitting behind an ASA firewal 8.2 and would behind accessing to web server 192.168.11.54 which sits behind the outside interface of the ASA firewall.The access would be like this:
1) 192.168.3.0/24 will be accesing to the web server http://192.168.11.54
2) We would like to translate the source 192.168.3.0/24 to the firewall outside IP address
3) We would like to translate the destination web server 192.168.11.54 to 202.90.197.146 as well
How to perform this simultaneous source and destnation address translation in ASA firewall 8.2? Could this be done in ASA firewall 8.2?
I am getting input errors/runts on 2 of my gigabit interfaces that connect to our WAN service provider's network. In relation to total packets, its not a large number, so its probably not a big deal, but I'd just like to find the source so I stop seeing the errors in Solarwinds. Our service provider says that they don't see any errors on their side, but the errors are incoming to us.
I've tried to capture the traffic with Wireshark, but discovered that often these packets are either discarded or padded by NICs so Wireshark will not see them, or at least will not see them as undersized.
Is there any other way I can capture these packets so I can find the source and figure out how to stop them? Our equipment is 3750G running 12.2(55)SE. Its not a trunk port. I know there was a bug in prior IOS that would cause some frames to be marked as runts even though they were forwarded successfully.
I need to open a port in a Cisco 2911 router to permit the conexion to an equipment that is inside the LAN, but I my configuration doesn't workt.
I have 3 interfaces configured: two WAN interfaces (one is a backup of the other) and a LAN interface. The configuration is this (public IPs are changed):
track 1 ip sla 1 reachability
!
!
interface GigabitEthernet0/0
description backup
ip address 176.55.25.25 255.255.255.252
ip nat outside(code )
We have a SRP527W, we have created VLAN for DATA and VOICE remotly connected to an office by VPN.
VPN is working fine.
Now we want to register SIP lines integrated in SRP527W to a Cisco Call Manager located in our office.
The problem is that the source of SIP packets is WAN interface of the SRP527W, so packet wont pass in the VPN. Is possible to change the IP source of the SIP registration ? The most useful will be to set the IP source SIP on the voice VLAN.
Does ASA 8.4.3 check the source IP address of a DNS reply and drop it if the reply address is different to that in the query?
Customers DNS server does this due to a recent change, their server now has a virtual address, but replies are sent from its physcial address. This is temporary. Their PIX is happy with this.
Replace the PIX with the ASA, DNS fails, the only reason I can see is due to the way their internal DNS operates.