Cisco WAN :: 2811 - Routing The Switch Ports
Mar 10, 2011
I have a 2811 router with a 9 port switch module and a four port ISDN module. The ISDN Module is our connection to the outside world. FE 0/0 and FE 0/1 are connected to separate networks and both route our the ISDN connections.We are getting a new satcom system that consists of a modem, antenna control unit (ACU), and an antenna. The ACU and the modem communicate accross Ethernet and are generally hooked to a switch. Anything computer hooked to the switch can simply use the modem IP as it's gateway and be surfing the Internet without much hassle (just need the correct DNS addresses).I'd like the networks behind FE 0/0 and FE 0/1 to be able to route out the satellite modem for their Internet connection -- when the satellite is available. Is it possible to put two switch ports in a VLAN (one for the modem and one for the ACU), give the VLAN an IP in the same subnet as the modem and ACU, and then tell the router to route traffic out the modem IP address ?
View 4 Replies
ADVERTISEMENT
Jul 23, 2012
we have cisco 2960 switch which is connected to a cisco 2811 router. flapping issue between these two devices??
The following actions i have taken, but no result.. I have changed cables. have set speed to 100 and duplex full on both the interfaces but the interfaces are showing up up still not getting connectivity. same i have to auto on both sides still no result what configurations should i set to resolve this issue...?
View 10 Replies
View Related
May 12, 2013
I have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
View 9 Replies
View Related
Nov 9, 2011
I like the SG-300 switches for SMB and I'd like use them in our network. Design is quite simple just 6 SG-300 switches connected to one central switch using SFP ports (using 2 port trunks) so I need 12 SFP ports and this is my question. Could you recomend me switch with more then 12 SFP ports from Cisco for this SMB network ? I don't know all the Cisco product lines and I can't find it.
View 2 Replies
View Related
May 23, 2011
Basically what is the difference. I'm looking at a breakdown of all the components connected to my switches I noticed half of them about are listing their port all the same as GI1/0/1 (routing port?). Then the rest are all different ports FA1/0/assigned# or FA2/0/assigned# (switch ports?).which are routing or switch ports and why certain ones are under each. It doesnt seem to matter which component it is (computer or printer) because some of each are under routing or switch ports.
View 1 Replies
View Related
Jul 13, 2012
The default Gateway and DHCP server is connected to port 1 of the switch. I have various other devices on the network plugged into other ports on the switch.I want port 1 to communicate with every port on the switch, but don't want the other ports to be able to see eachother unless I specifically allow them to. For example, port 5 should see port 1, and 7, but nothing else.Everything needs to be in the same subnet. With the older Dlink switches I am used to this feature is called "Port Segmentation" but I see no such option in this switch. I have been playing with the VLAN settings but so far I have not been able to achieve this.
View 7 Replies
View Related
Feb 5, 2013
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
View 5 Replies
View Related
Feb 20, 2013
I was viewing the 3560x switch datasheet and i need network module C3KX-NM-10G. I have dark fiber with over 12 km distance to i guess i will be needing SFP EX for single mode.
View 3 Replies
View Related
Aug 24, 2011
I have 2 3550's connected across a wireless link. [code] However, from Switch A, I cannot reach 10.1.3.9Can this 3550 not route traffic between 2 routed ports?
View 8 Replies
View Related
Feb 19, 2013
My SG200-50P Switch Log appears as follows with Random ports going up and down. I am trying to find out if this links to another problem I'm having with a Client Server software locking up on the client end. The hardware, thin clients and desktops, are working and have checked all sleep and power settings. All items in working order, now I'm wondering about the switch
2147483369 2013-Feb-20 15:12:07 Warning %STP-W-PORTSTATUS: gi19: STP status Forwarding
2147483370 2013-Feb-20 15:12:02 Informational %LINK-I-Up: gi19
2147483371 2013-Feb-20 15:12:00 Warning %LINK-W-Down: gi19
2147483377 2013-Feb-20 14:51:31 Informational %LINK-I-Up: gi45
2147483378 2013-Feb-20 14:51:28 Warning %LINK-W-Down: gi45
[code]....
View 1 Replies
View Related
Jan 22, 2012
I've a 7206VXR (NPE-G1) router. I would like to purchase a PA-GE port adaptor where I've to use a GBIC connector.
1. Is it possible to have a connection between PA-GE and a 3560G switch (4 SFP ports)? If yes, what type of cables & connectors are to be used?
2. Is there any GigabitEthernet port adaptors / modules for 7206vxr where I can connect RJ45 (cat 5) or SFP modules?
View 4 Replies
View Related
Feb 1, 2013
I have been reading the postings on this site trying to retrieve the MAC address for the client devices (computers, printers) attached to our switches. We have approximately 500 switches and I need to map the mac address to the switch. It appears the OID information is for SNMP v2. We are restricted to using only SNMP v3. I have tried using the Cisco SNMP Object Navigator without any success.
View 2 Replies
View Related
Feb 24, 2013
I have a Cisco 4500. Recently some of the ports seem to have "died"/ will not supply Poe to phones. Some work for data only. Other do not work at all. The switch has been restarted, this made no difference.
View 2 Replies
View Related
Feb 4, 2013
I have a 2960 switch and every then and now the ports are flapping, while i was on console i saw ports going down and coming up...when the ping to machine ip addresses timed out the port status on switch was still up...no errors collisions seen on sw port. Below is sh int when the port was flapping
[code]...
View 1 Replies
View Related
Jul 24, 2012
I have a got a requirement where a 24 Port Switch should have 4 SFP's and all 4 should be used at a time, So I've chosen " WS-C2960S-24TS-L"
The transeiver should be GLC-LH-SM, so kindly let me no whether I would be able to use all 4 ports at a time or not.
View 2 Replies
View Related
Mar 22, 2012
I have a site that is connected to the internet via T1 into 2811 runing C2800NM-ADVENTERPRISEK9-M), Version 12.4(11)X. I have noticed that when i do a port scan on the outside nat pool i see well know ports in the closed state .ie...7,21,22,23,25,99,100,80,443. These pools for end users to access internet. Does this pose a security risk? What can i change to provide end user access to web but not let these well know ports open?
View 6 Replies
View Related
Jun 14, 2012
how many extra interface port can be plugged in to the 2811 router ,there are 2 fixed FE port on this router and i have 3 connection i.e one mpls link , one internet link and one sip trunk .. some body confirm me that i can insert module in 2811 ?
View 5 Replies
View Related
Jan 31, 2012
I work at a hospital and we have 3750X-48P switches in stacks in various locations throughout the hospital. We have noticed that when an EKG machine is plugged into one of the ports on some of these switches and the EKG machines are set manually to 100/Full, the ports are no longer usable until the switch is restarted. The switch is configured for auto. If the EKG machine is set to auto, it will work and not cause problems. The link on the interface will show up/up and there will be output packets increasing. However, there will be no inputs on the link and the port is unusable. Unfortunately, even when the device is removed, the port becomes unusable for any device. Is there any way to fix this problem without rebooting the switch?
View 5 Replies
View Related
Feb 29, 2012
In my environment we have 3750x switches running ios 15.0 (1) SE2. We have port security mac address sticky configured on all our switch ports. I noticed that we have several interfaces (on different switches) that are up but have not captured the MAC address from the workstation. Here is one example:
interface GigabitEthernet2/0/11
switchport mode access
switchport port-security
[Code].....
View 21 Replies
View Related
Apr 24, 2012
I was checking some things on my Cisco 4500 and spot checking some of the ports. Using CNA it says it is at 10. The web browser to the switch says Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000-TX on port 6i/18 The CNA says, so what would cause the difference?
View 3 Replies
View Related
Jun 5, 2012
I have a Cisco 3750G-48PS Running IOS 12.2(40) and was wondering how many physical ports are supported in an LACP Configuration. Is it 4 or 8 ports in a single switch.
If I have a dual 3750 stacked together, and I want to configure (8) port LACP, Can I take (4) ports from each switch in the stack and LACP together.
View 4 Replies
View Related
Aug 7, 2011
How many of the 881 switch interface ports can be used as router ports, have used the 877 etc where i can use 2 but need a low cost router that supports 3 for routing. (needs to be physical ports)
View 2 Replies
View Related
Sep 6, 2012
Have our public IP address space masked on /24 at our Internet Router. The router portion of 3845 connects to Internet, while the internal switch connects to my internal network and seeds it with the public address space. The switch had a port configured no switchport (L3) with an ip address with /24 (ie 67.63.145.1 /24) this connects to internal IPS/IDS then to Firewall which NATs to internal, then packet shaper, web filter etc etc etc. I need to test my ISP speed so I need to "break in" to the link between the switch and the IPS/IDS. I figured I could configure another port on the switch on the 3845 but my problem is the port to my network is routed and is masked on entire /24. I tried to configure a port on VLAN 1 and give myself an available address in the L3 address space and this did not work (figured it would not but gave it a try)
Any way to get two ports configured to use the same subnet while one is a L3 routed port and the other is just part of that layer 3 routed network?
View 1 Replies
View Related
Dec 11, 2011
i recently deployed cat4507e switch along with 3 nos of WS-X4748-RJ45V+E - 48 port gigabit PoE modules. I am using polycom IP560 phones.
I am facing issue of some switch ports (randomly) stops supplying power to phone at random time. So far there are about 4 incident and i have been plugging those connection to different - usused ports. I am planning to RESET the switch module during weekend and i think it might fix issues with those ports.
But what would be quick and easy way to fix this issue when the issue is faced? How/what to check on switch port interface wrt to power? If switch module is falling short of overall power requirement, is there a way to boost the power?
View 17 Replies
View Related
Dec 19, 2011
Is there a switch that handle its 24/48 ports at 10 Gbps with copper?. I have checked 3750 X but just handle 2 SFP with 10 Gbps.The requirement is to use this switch as CORE and connect 12 switches (access) using its uplinks at 10 Gbps with copper ( in this case 3750 X can be used).using copper at 10 Gbps the distance is still 100 m?
View 9 Replies
View Related
Feb 2, 2012
I have to configure failover Active/Standby on my ASA 5510.I am wondering how i could do for the outside interface, i mean, actually the ASA1 outside interface is linked directly to our Internet router.So now if i have to add ASA2 connecting to that router i will need a switch between them.I have already a switch for DMZ & LAN.The thing is that i will have to allow 3 switchs ports to communicate with each others.
- 1 for ASA1--outside
- 1 for ASA2--outside
- 1 for Internet router
How could i isolate these 3 ports to make them communicate alone ? Should i use VLAN for that ?And if i use VLAN, will this require to make any change of configuration on my firewalls (ASA1 & ASA2) outside interface ?I am a bit lost with this, if i am correct i will not have to do some "vlan tagging" on the firewall itself ?
View 1 Replies
View Related
Jan 10, 2012
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
View 4 Replies
View Related
Oct 26, 2011
I am working on a request to clean up alot of excess cabling in one of our IDF's. I noticed that many of the connections have no lights on them and probably haven't been used in a long while. I would like to know if there is a CLI command I can run on the Cisco 3750 switch will allow me to bring up a list of ports which have not seen any activity for a period of time - for example, 30, 60, or 90 days.
View 3 Replies
View Related
May 18, 2012
I have a 2960 and a 2811 with a hwic card I have one port set as 100 meg and another port set at 10 meg. Both are set to access mode. i need one port for failover (10 meg) . I can't do ether channel on the hwic. How do I prevent a loop when I connect my second connection. While having both connections up. Should I use bpdu guard? the goal is to have one port fail over if the 100 meg goes down. And I'm currently running ospf so it should take the faster connection.
View 1 Replies
View Related
Feb 14, 2013
Can i configure access ports into port channel on Nexus 7K switch.If possible then provide the complete configuration.....
View 2 Replies
View Related
Oct 8, 2012
I have 4 cisco 2960 switches to which many users are connected. No vlans are the only default vlan 1 is there. Now I want to make ether channel on switch 1 whcih has 24 fast etherenet ports. Can I make port 1- 8 as one ether channel which are connected to users or i can only make ethere channel of ports that are connectd to other switchs. If I can, how the other switchs will comnicate with the switch ports bundalled in the ether channel in switch 1.
View 6 Replies
View Related
Sep 17, 2012
I have a Cisco 6509 with IOS "s222-ipservicesk9_wan-mz.122-18.SXF16.bin"I need to enable dot1x on user's ports on the switch. each user is connected to the switch through the IP phone.
I just found out that I can not enabled dot1x on trunk port. I have tried to use "switchport voice vlan " but I got:
Switch(config-if)#switchport voice vlan 123
Command rejected: Gi7/20 is Dot1x enabled port.
let me know what should I do to get dot1x working?
Note: I have connected a laptop directly to the port and dot1x is working fine.
View 5 Replies
View Related
Jul 1, 2012
Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
View 2 Replies
View Related
