Cisco WAN :: (2911 / 1941/ 2901) Errors With DCE On Same WIC-2T?
Feb 5, 2013
I am having this issue with only one rack in the lab. The three routers (2911 , 1941, 2901) connect together through Smart Serial cables going to WIC-2T cards. In the configuration both serial connections going to the 1941 have the DCE.
When going to configure serial 0/0/1 I am allowed to apply a clockrate to it, however, I am kicked back an error saying that a clock rate can only be configured on DCE interface. They are both without a doubt the DCE end connecting to the WIC-2T interfaces. What could possibly cause this problem. Would SCTE or something with the auto clock-rates on the router create this problem.
View 2 Replies
ADVERTISEMENT
Aug 29, 2012
We have recently put in a new 2901 router to be our IPSLA router and after adding 430 operations to it (215 ICMP and 215 UDP jitter) to cover off our state wide sites, it's reporting over half of them as timing out. Over the day, the timed out operations change so that our monitoring system shows the operations as down most of the time and up or warning state the rest of the time.
Some of the remote routers are reporting "SLA_FORMAT_FAIL" errors but I cannot find any references to this error.A ping from the router to the remote site router returns a ping time of 50ms or less and the network links are not conjested so QoS shouldn't be getting in the way. Our QoS policies would mark and prioritise the UDP jitter test traffic and the ICMP would be in the default class.
The 2901 is running 15.2(4)M1 and has 512MB RAM and 256MB flash. It's single homed into our core network switch. I've heard stories of 2900 series routers hosting 1000's of operations so I don't think we're taxing the router. CPU is sitting around 5% and memory is around 20%.
Below bits are for one set of operations.
*******************************************************************************************
End node we're targetting (2951 running 15.2(3)T):
DC204RT04#ping 172.16.37.192
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.37.192, timeout is 2 seconds:
[code]....
View 3 Replies
View Related
Oct 2, 2012
I have 1941, 2901 ISR routers. I will use 3G backup when primary link (metro ethernet / G.SHDSL) goes down. Do I have to use Data License (SL-19-DATA-K9 / SL-29-DATA-K9) in order to switch back to 3G when primary link is not reachable) ?
View 7 Replies
View Related
Feb 13, 2011
Im getting flooded with the following messages: Feb 14 10:47:19.740 EST: PLATFORM-5-ECC_MSG: A corrected single bit error has occurred in L2C Data Cache at location 0x294.
[Code]...
View 1 Replies
View Related
Dec 5, 2011
I have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies
View Related
Jun 10, 2013
Does the 2901 have etherchannel capabilities? If so, how to configure it? I mean, I can type "show etherchannel 1" in it, so I would assume if I can show it, I better be able to configure it, right?What about the 2911?
View 1 Replies
View Related
Sep 13, 2011
I have a AIR-AP1121G-A-K9 running c1100-k9w7-tar.123-7.JA2 (Autonomous)We have monitoring setup with Orion NPM and we consistently see output errors, Transmit discards and big buffer errors The users at the site have not reporting any issues but was wondering how to prevent these or are these normal?What causes the output errors on Wireless Radio ? How to troubleshoot further ?
Radio0-802.11G
Total Output Errors 0 47749
Small Buffer Misses
4 misses
139 misses
[code]....
View 1 Replies
View Related
Dec 25, 2011
I am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
View 2 Replies
View Related
Nov 9, 2011
What ISO do I need to purchase to get Cisco IOS Firewall on a Cisco 2901 - is it just IP Base or do I need one of the Security IOSs?
View 1 Replies
View Related
May 24, 2011
I have a 1-Port 3rd Gen Multiflex Trunk Voice/WAN Int. Card - T1/E1 in a 2901 that I want to configure for data only (T1 connection to the Internet)I don't see any options in the IOS for using this thing as a serial interface (data), only options for configuring PRI/ISDN.
View 5 Replies
View Related
May 25, 2011
The license has been installed onto the router. Here is the relevant out from the show license all:
License Store: Primary License StorageStoreIndex: 0 Feature: ipbasek9 Version: 1.0 License Type: Permanent License State: Active, In Use License Count: Non-Counted License Priority: MediumStoreIndex: 1 Feature: WAAS_Express Version: 1.0 License Type: Permanent License State: Active, Not in Use License Count: Non-Counted License Priority: Medium
WAAS license as it says that this is not in use, WAAS under the interface is not possible.
View 1 Replies
View Related
Feb 23, 2011
I am trying to come up with a config for implementing QoS over a 512 kbps WAN link that will traverse voice and data traffic for now. I am using a Cisco 2901 router with 15.1(3)T IOS on it. my config is below
class-map match-any DATA-PRIORITY match protocol citrix match protocol sshclass-map match-any VOICE-CONTROL match protocol skinny match protocol mgcp match protocol h323class-map match-any VOICE match protocol rtp audio class-map match-any ANY match any [ code]...
THE ISSUE IS : when i add in the service-policy output WAN- QOS- POLICY command , i get the error " insufficient bandwidth 256kbps for bandwidth guarantee (180)". if i take out the " bandwidth 512 " command out then i get no issues adding the above command on interface g0/1
View 3 Replies
View Related
Jun 9, 2013
I have a Cisco ASA and a 2901 Cisco Router connected via site-to-site VPN. The ASA can ping over the VPN to computers behind the router, but the router can not always ping to computers in the ASA network. When i ping from a computer in the IOS router's 10.100.36.0 network the requests times out most the time; although every few minutes, i will get about 10 pings back, then stops working again.
I uploaded their two configurations.
The ASAs public IP is 20.20.20.5 and local (inside) network of 10.101.36.0/24
The IOS routers public IP is 20.20.20.10
There are many internal networks, but 10.100.36.0/24 is the one with issues.
View 1 Replies
View Related
Feb 12, 2013
I've got router as vpn-concentrator which receives vpn site-to-site connections from 10 branches with cisco 881 and cisco 1941.I started cacti monitoring and found out that there are too many errors on interfaces.URL.
View 5 Replies
View Related
Nov 6, 2012
I try to make a gre tunnel with 2 cisco routers 2901, ping responds between tunnel ip's ends, but I don't have pings from the pc's inside the networks. [code]
View 7 Replies
View Related
Feb 7, 2012
How do I disable fragmentation on a 2901 router? I want it to simply drop packets oversized packets.In my lab, I am trying to test various MTU issues. I'm trying to use a 2901 router to simulate the WAN equipment that my WAN provider would deploy in production. In production i'm expecting the WAN to only support an MTU of 1320 with no fragmentation at all.
View 2 Replies
View Related
Jan 1, 2012
Physical devices are a Cisco 2901 (CISCO2901/K9) with GE0/0 configured as 192.168.1.1
Connected through a D-Link DGS-1210-24 configured as 192.168.1.202
Running on a domain with an HP domain server as 192.168.1.2
The 2901 was an EHWIC (VA-DSL-A oPoTS) on EHWIC 0/0/0
GE 0/0 on the 2901 is physically connected to the DGS-1210 which is physically connected to the server.
VDSL 0/0/0 is physically connected to the DSL jack.
So far the configuration reports all is connected, and I can ping the gateway of our ISP (using CLI or Cisco CP); however the server reports no internet connection and no workstations can access the 'net.
Once connected; I'd also like to allow ports through for use on the network (25, 80, 110, 443, 987, 1723) - but not sure on how to do that just yet!
Our IP is 202.27.19x.19x
Our Gateway is 202.27.217.5
[Code] ......
View 11 Replies
View Related
Jan 27, 2013
I have recently bought cisco 2901 in order to replace it with our 1811W that we have at the moment.When I try to set a failover / backup with rtr; it seems like the function is not valid.Once I select rtr and set the object #, the reachability command is not available.Does that mean this function is not a part from the license package I have?
View 6 Replies
View Related
Oct 4, 2011
I have inherited a setup for a custom application and would like to know if this is the only way this could be set up. How would you do it?The application uses dedicated T1 links to our vendors. There is a Cisco 2901 router in the middle providing the connections. Traffic to specific vendor's IP's are routed to their prospective connections. I have attached a network diagram and a config for the 2901. The way my predecessor(s) set this up, each different vendor uses a different private IP address for the internal links. This seems odd to me. Shouldn't there be a way to have only one subnet on the inside and have the links NAT depending on which route it takes? The servers have persistent routes built in them to send vendor traffic to the associated IP on the router. E.g., traffic to Vendor 1 is routed to 192.168.50.1, the 2901's IP address for the Vendor 1 network. That traffic is then NAT'd to an IP address associated with Vendor 1's link and the 2901 then routes the traffic to the Vendor's end of the link.
I would think that I should be able to revamp this so that internally we're only using one subnet and the traffic could NAT at the link associated with the Vendor. I recently had to add the 3rd vendor connection, and wound up having to duplicate what was done for the other two in order to get it working quickly. I didn't have the time to wrap my head around the best way to revamp the whole thing.
View 3 Replies
View Related
Jul 6, 2012
I recently obtained a 2901 router running 15.2(2)T to replace my old 877 which was running 15.1(4)M1. The 2901 is humming along quite nicely but I have had difficulty configuring one feature which was working fine on the 877. The router needs to be a PPTP client to a hosted VPN service. On the 877, I had it configured like this: [code] I then had a dialer interface to actually set up the connection, and some PBR to control what went over the VPN. All well and good, and it worked fine. But on the 2901, when I try to configure the same thing, there is no such command as "protocol pptp" -- the only option is protocol l2tp.Was PPTP support deprecated somwhere between 15.1 and 15.2, or does the 2901 itself not support it for some reason? Obviously I understand that l2tp is superior to pptp, but at the moment this is my only option.
View 2 Replies
View Related
Mar 17, 2011
I have one router 1841 in which i configured PBR for internet traffic from LAN. I hv two ISPs few server are configured for ISP1 and few for ISP2.I planned to shift my existing setup at 2901 G2 router. when I am configuring the same config on this router so traffic is passing through only from one ISP not from other, if I troubleshoot so I see that the interface which is connected with ISP2 is not getting any input/output packet.
Config is here:
==========
interface FastEthernet0/0
description ****** ISP2 ******
ip address 203.xx.xx.110 255.255.255.248
[Code].......
View 1 Replies
View Related
Nov 5, 2012
I try to make a gre tunnel with 2 cisco routers 2901, ping responds between tunnel ip's ends, but I don't have pings from the pc's inside the networks.
[code]....
View 5 Replies
View Related
Jun 2, 2012
Why I cant correctly use ip sla command. I only have on my 2901 such commands: ip sla ?
key-chain Use MD5 Authentication for IP SLAs Control Messages
responder Enable IP SLAs Responder
server IPPM server configuration
There is my "sh ver"
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
And...What should i do. if i want to create a failover with to WANs
View 2 Replies
View Related
Jul 2, 2012
Where's the ideal place to put the KS? My current setup is 1 KS, 19 GM. The KS sits BEHIND a GM, so all other GMs have to come through one GM to get to KS.Now, I have purchased two dedicated KS routers. I configured one today, and placed it right on my WAN. My WAN is a L2 Ethernet domain, so i just provisioned a switch port in the WAN vlan, and away we go. I copied RSA keys over from the current KS, configured redundancy and the two hooked up, saw each other and it seems to be good to go. For the ACL, I put in an exclustion for my two KS to talk to each other:
deny ip host 192.168.250.40 host 192.168.250.41 (Old IP, New IP)
deny ip host 192.168.250.41 host 192.168.250.40.
I used a test router and pointed it to the new KS, it registered without a hitch... HOWEVER about two hours later (my 7200 second timeout) I lost ALL my branches. My 18 other GM were still pointed to the OLD IP only, they didnt have the second IP configured yet. In a hurry, I quickly disabled the redundancy configuration on the old KS and had to go to each GM and do a 'clear crypto gdoi' on each one to get them to re-register. There were no log messages about not being able to rekey, no log messages about dropped peerings, nothing. Once I did that, everything returned to normal.
The Question I have...
Would having configured the redundant KS caused this problem? Would having one KS behind a GM and the other Coop KS in the WAN make a difference?
Relevant config from existing KS, 2801:
crypto gdoi group GETVPN_GROUP
identity number 1234
server local
rekey retransmit 60 number 2
rekey authentication mypubkey rsa GETVPN_KEYS
[Code]...
View 2 Replies
View Related
Apr 18, 2011
I have a 2901 ISR G2 router, with IOS 15.0.1M3 , this router is not working with static NATing, I have tried to configure this router with one internet link and make few static translations with it. But this configuration is perfectly working with 1841 ISR router.
View 2 Replies
View Related
Jun 9, 2013
We've have a client who had a ordered 2 units of 2901 router to have site to site connectivity. User has bought a leased line of 256kbps from service provider in between two sites, but the issue is the service provider has layed a rj11 cable and there is no rj11 interface on 2901 router it only has two rj45.
View 5 Replies
View Related
Aug 7, 2012
Need to know if I have 2 type of license on my 2901 router: ipbase and uc, will the 2 type of fuctions of this license work at the same time. Another words will i have route and nat functions work with voip having to type of license on my 2901?
View 3 Replies
View Related
Sep 15, 2011
I been working with PPTP server on cisco IOS since a log time ago. Up to release 15.0 seems is just stopped working. I mean external users can log in the pptp but after logged in there no traffic flow. A simple downgrade to 12.4 solves the problem.
But now i have all my infrastructure with ISR2 2901 and all IOS are 15.
View 5 Replies
View Related
Feb 28, 2013
I'm trying to run the ISM-VPN-29 in a 2901 router. Cisco says that the SECK9 and HSECK9 licenses are needed to operate this ISM. However, they also say that the HSECK9 license is not available on the 2901. I'm running the SECK9 license but it's still not working.
This link, table 5 states that the HSECK9 feature license is for 2921 and 2951 only:[URL]This link states that it is a requirement to run the card, and also that the card works on the 2901:[URL]
I am running 15.3(1)T IOS.
View 3 Replies
View Related
Feb 19, 2013
I have a issue where after configuring aaa and rebooting, logging into the console port seems to be auto trying something before it finally times out and let's the user try. I getting the following sequence: [code] I need aaa to work via vty, however I need the device to boot directly to the Username: prompt so I can continue to use my VB script to clear the config when the devices are return from the field.
View 4 Replies
View Related
Sep 1, 2011
Any info concerning the installation of CW LMS 4.0.1 on Solaris 10!
The installation keeps on failing when it is checking for packages. Also the second time when we downloaded the software once more.
ERROR: AddProperty called with invalid package name: CSCOmd.
I have also attached the install log files.
The system is Solaris 10 with zones:
bash-3.00# more /etc/release
Solaris 10 10/09 s10s_u8wos_08a SPARC
Copyright 2009 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to license terms.
Assembled 16 September 2009
121133-02, 125503-02, 126897-02, 127127-11, 127755-01, 138866-01 Incompatibles:
[Code] .....
View 5 Replies
View Related
Feb 23, 2011
I am seeing a lot of the following showing up in the WLC trap log:
Decrypt errors occurred for client <CLIENT-MAC> using WPA2 key on 802.11b/g interface of AP 00:17:0f:81:ad:90
we are using WLC runninn 7.0.98 and ACS 4.0
View 2 Replies
View Related
May 9, 2013
I am installing LMS 4.1 to windows 2008 R2 SP1.Server hardware meets requirements.A the end of the installation I am getting from the installation log file the following warnings/errors. [code]
View 5 Replies
View Related
