Cisco WAN :: 3845 / QOS Affecting On GRE Tunnel?
Sep 18, 2012
on our cisco 3845 router we have recently applied a qos policy on a fast ethernet where our MPLS link is connected. We have already having a GRE tunnel over the fast Ethernet with one of our site. Now we are observe the application working slow over the GRE tunnel. When we have removed the qos policy from the MPLS link the application are working fine.My question is why it is happning on the gre tunnel. So how to overcome the problem. Shall we need to apply the qos policy on the GRE tunnel alos ?
View 1 Replies
ADVERTISEMENT
Aug 26, 2012
We have a Cisco 3845 router for Site 2 Site VPN tunnels to external business partners. The IOS is (C3845-ADVIPSERVICESK9-M), Version 12.4(15)T8.One of our partners is doing a DR test and needs to have us swing the VPN traffic to another peer in a test location temporarily. I plan on adding the test hosts to our existing encryption ACL, but instead of building another crypto map, I was wondering if I can add a secondary peer to the existing one?
View 3 Replies
View Related
Apr 23, 2012
So in our DMVPN network, we have this Cisco 3845 hub router that is connected via a DS3 to the Internet, and our spoke sites usually have a broadband connection that typically have a maximum of 1Mbps upload capacity. We are getting ready to add a few more sites to our network that are connected to the Internet with 10Mbps upload speeds (and 50Mbps download). Spoke site routers are usually 800 series ISRs. We have seen spikes of 8-10Mbps on the hub router so far. So the question is that a site with 10Mbps upload speed transmit to the full capacity over a DMVPN tunnel or is it limited by other factors? What are those factors?
View 4 Replies
View Related
Sep 19, 2011
I am trying to implement RBSCP on two 3845s running 15.1(4)M1 Adv Enterprise over a satellite link. The "show" commands all look correct, but whenever I policy route my machine through the RBSCP tunnel I dont even make it to the opposite side. However, if I remove the "tunnel mode RBSCP" command so it acts like a regular GRE tunnel, I route through it just fine. So I know its not a NAT, routing issue. [code]
View 1 Replies
View Related
Feb 16, 2012
I have two Cisco 3845 routers which receive a multicast stram via a tunnel interface, i.e Tunnel163 (PIM Dense mode is enabled). These routers are both connected to a LAN segment (FastEthernet0/1/0) where receivers are. [code] Router1 is the assert winner (highest IP address), it sees igmp joins request, but it's pruning the interface. It happens sometimes and it lasts until I manually issue clear ip mroute.Unfortunately I cannot migrate to Sparse Mode.
View 15 Replies
View Related
Apr 27, 2011
I work as an administrator for a small business (~30pc and a Windows 2003 R2 server ).Recently, we started to have problem with our lan, the network start to kinda lock-up randomly. For example, browsing folders is fine then you switch to one and the explorer window just do nothing (with a loading cursor) and after 4 second everything refresh and work again, then in word or any other program (sometime not even related to network files/folder) you press the save button and it do the same, do nothing for 4-5 seconds then refresh and work again.I'm positive that no process on the server take up enough CPU time to do that, it's not a per-pc problem since everybody is affected when the problem start and when I reboot the server it work like a charm for another day then the problem may restart the next day.Nothing show up in the event viewer of both PCs and the server and we can't find a correlation between the problem and high CPU/LAN usage on the server (at worse CPU is used at 10% and LAN at 2%).Our RAID controller and our SAS HDs are working flawlessly, we're in the process to change our infrastructure anyway but since I can refer to people that may know their stuff way more than myself I though Id ask here.We first though that our switches may be in cause but then why rebooting the server would be correcting the problem ?
View 7 Replies
View Related
Dec 20, 2011
Cd/rw drawer was bumped and now is most likely off track. Closed now, but now computer is not functioning correctly and will not connect to the internet for some strange reason..have unplugged and disconnected and reconnected all, to no avail. This is an older tower and belongs to a neighbor.
View 2 Replies
View Related
May 11, 2013
If I could swap around the bootvar on my 5505 without affecting the activation key.this is to learn different NAT on pre and 8.3+ IOS.
# sh bootvar
BOOT variable = disk0:/asa825-26-k8.bin
Current BOOT variable = disk0:/asa825-26-k8.bin
CONFIG_FILE variable =
Current CONFIG_FILE variable =
[code].....
View 3 Replies
View Related
Jan 31, 2012
win 2003 dhcp server. when I leave dhcp services OFF i can ping the server fine. once i turn ON dhcp services the connecting drops in and out.. what is going on here?
My users are unable to get a steady connection to the dhcp server.
View 8 Replies
View Related
Dec 10, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and wondering if PWR-3845 AC is for one power supply and AC/2 means you get two with one order?
View 1 Replies
View Related
Dec 27, 2011
We have an ASA 5505 and I want to block www.facebook.com for all users on the inside network. I followed the instructions laid out in Cisco support document ID 100513 using regular expressions with MPF but am running into some problems.
[URL]
Once the configuration has been changed based on these instruction www.facebook.com is blocked. However I can't access any other websites except my Google News home page comes up just fine for some reason.
ASA Version 7.2(3)
!
hostname ciscoasa
domain-name default.domain.invalid
enable password 4nJloDG8uYd8w4D3 encrypted
names
!
interface Vlan1
[code]....
View 18 Replies
View Related
Dec 7, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and if PWR-3845 AC is for one power supply and AC/2 means you get two with one order.
View 1 Replies
View Related
Jan 9, 2011
i have a 7201 router with NPE-G2. i have a design which i have the option to send all the traffic through a GRE tunnel or a L2TPV3 tunnel.which method is more CPU consumption ?
View 1 Replies
View Related
Sep 23, 2012
I'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies
View Related
Oct 17, 2012
I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
View 3 Replies
View Related
Jul 24, 2012
Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies
View Related
Jan 23, 2012
There are a few situations were I'd like to be able to use the locally configured account on a device but still have ACS in place.I want to complete this WITHOUT adding the locally configured account into ACS.I have tried setting the advanced option under Identity for if an account is not found to "Continue" however this causes the account to be allowed as long as a password is typed (any password, as long as its not blank).
View 2 Replies
View Related
Mar 10, 2013
I have cisco 3845 on my network now its working fine.Now one of my client is asking to they want to connect their network through my router ethernet interface.
now my doubt is 3845 router will support two different gateways.
how can i route their network they have bring new router.
View 2 Replies
View Related
Mar 7, 2013
I have 2 x Cisco 3845 each one with a DS3 circuit, both running c3845-spservicesk9-mz.124-15.T3. In each of them I have one pvc provided by my carrier and I received the following info to configure:
vc-class atm ATM
vbr-nrt 44096 44096 1
oam-pvc manage
oam retry 3 10 1
encapsulation aal5mux ip
That worked fine for the first one with the NM-ATM-DS3, however, using NM-1A-T3/E3, it seems that I'm restricted up to 40700 kbps PCR/SCR:
router(config-vc-class)#vbr-nrt ?
I tried to look for some reference but couldn't find... Is there a way I can have a full DS3 with this card?
View 8 Replies
View Related
Jun 28, 2011
We have 3845 Router which is using for only Internet connectivity with one ISP(X) Customer has only one Vlan, Public AS number, and Public IP pool.Scenario:User--> L2Access-SW--> L3 (6500) SW--> Firewall (5520) --> IPS--> 3845Router.Now we have another ASR Router, which also has Internet connectivity from another ISP(Y).Now the issue is we would like to use both ISP in active/active scenario.
View 1 Replies
View Related
Dec 31, 2011
I have two routers 3845 and HSRP is configured properly. Currently we are using default route to ISP and right now I want to use BGP as I have 3 Public pools and that's why I want to advertise in the public network. How I can configure that in my Router.
View 1 Replies
View Related
Apr 21, 2013
I am replacing our core router, which is a very old 7204VXR, with a T3 card in it. We are using it to terminate about 10 point to point T1's. It is also the central gateway for our entire network.
I am planning on replacing it with a 3845, and an NM-1T3/E3 card for my DS3. I think I've got that part worked out.
My real question is concerning future upgrades. We are trying to convert many of these point to point connections to Metro Ethernet, and get rid of the huge DS3 cost. When that happens, I'll probably have a handful of point to point T1's left over (maybe 2-6 of them). So, what I need is a good solution to terminate those 2-6 PTP T1's in my 3845. In the past I have just been using the old WIC-1DSU-T1-V2 cards to terminate my T1's. I am looking for a solution that won't break the bank. I looked at both the HWIC-4T1/E1 and the NM-8CE1T1-PRI cards (which terminate 4 and 8 T1's), but they are like $4,500 and $8,500 respectively. That's way beyond my budget for these. I definitley don't need a card that will do PRI's (DSP's etc.). I just need it to terminate plain old point to point T1's.
So it may be that I'm just looking at the wrong cards. Or maybe the make cards that will go in the back of the 3845 that will house 2, 4 or more WIC slots, and I could just use WIC-1DSU-T1-V2 cards?
View 6 Replies
View Related
May 6, 2013
I am upgrading from an old 7204VXR to a 3845. I am running a DS3 in the 7200, channelized into 28 point to point T1's. I need to break them all out into individual Serial interfaces on the new 3845, like I have on the 7200, but I don't know the correct commands.
[code]...
View 5 Replies
View Related
Mar 24, 2011
I am installing Cisco blank CF upgrades (double the capacity of the CF that came with the router) in Cisco 3845 routers and I cannot get the IOS to load.
Network security requires tftp be disabled, so I am limited to xmodem. Slow, but it works. I know the IOS download is good, because I can load it on the CF that came with the router.
I can install, format and read the new flash. But the download locks up and bombs about 1/3 of the way through.
Note: CF that came with the router was "C" so I used the format flash: command. The new flash reads the same as the old, except that there is no file IOS loaded.
I've never had an issue upgrading an IOS, but this is my first shot at installing on a new CF.
View 10 Replies
View Related
Apr 26, 2011
1841 & 3845 router. We send 30 GB data on 100 Mbps link. First time we use 3845 router for sending the data and 47 Min are required to complete the data, during this link utilization was 100%. After that we send same data through 1841 router & 46 Min are required for the same. Only difference in data transfer is CPU Utilization of 1841 router goes 30% & 5 % of 3845 router Can we use 1841 router instead of 3845 router ? .
View 2 Replies
View Related
Apr 26, 2011
I have 3845 router where 200 branches are connect. Ho have database server where branch are synch interval period.some of days observation cpu load average 70 % and sometimes it reaches 100 %.yesterday when I give command clear arp then instant cpu load reduce and 20 % yesterday cpu load 12-20 %. Today morning when I give command Cpu proc history then I found cpu load 60 % and at night it was 3 times reaches 100 %. so my question is after clear arp command at least 10 hours cpu utilization 20 % but after that it increase.so for any LAN broadcast it happend ? how i understand cpu high for Broadcasting or anything else.
View 2 Replies
View Related
Feb 6, 2012
I have a 3845 Router with three connected interfaces, one to my WAN, one to my LAN and another to my wifi zone. I want to limit the amount of WAN bandwidth the WIFI zone can take to say a max of one third and not restrict WAN bandwidth from the LAN at all.
View 7 Replies
View Related
Aug 18, 2011
I have a router 3845 connected to a LAN and other routers and providing internet through a link on an ethernet interface
Gi0/0
LAN connection
GI0/1
WAN connection
fa0/0
Internet connection
View 9 Replies
View Related
Nov 12, 2011
I received a syslog message on my cisco 3845 router, what is that message mean. 11 13:36:06.265 UTC: ASSERTION FAILED: file "../les/if_ng_dslsar_tx.c", line 385
View 2 Replies
View Related
Dec 27, 2011
I wanted to confirm if the NM-2W is compatible with 3845 (says it is compatible) and 3945.I wanted increase WIC density in these routers to install ISDN HWIC-4B-S/T 4-port ISDN BRI High-Speed WAN Interface Card.However, i am not sure if these cards are compatible on the NM-2W. Is there any other NM* module that can extend WIC density on those routers.
View 1 Replies
View Related
Jul 14, 2012
I am using cisco (C3845-ADVIPSERVICESK9-M), Version 12.4(11). some static nat is configured. Now i want to remove all nat and configure again? i am using router# clear ip nat translation * router (conf) # no ip nat ...... but no enty is beign delating. How to detate all nat or single nat?
View 5 Replies
View Related
Jun 8, 2011
I am facing a issue on Cisco 3845 router, IOS is :c3845-adventerprisek9-mz.124-22.YB8.bin
I have changed the IOS as well as the Hardware but again the router is restarting. I have put the show tech-support and crash-info in Output interpreter, result is below:
ERROR MESSAGE NOTIFICATIONS (if any)
%PAR-1-FATAL (x): [chars]
Explanation: A parity error has occurred. The problem might be caused either
by a motherboard that has failed or motherboard settings that are incorrectly
set.
[Code].....
View 1 Replies
View Related
Dec 6, 2012
I have a 3845 that will not let me ping to the internet from my PC.On interface g0/0 I have a connection to a internet connection (another router), using DHCP to get it's address (it gives g0/0 IP 192.168.0.3).On interface g0/1, I have a connection to my LAN (I assign the interface IP 10.10.1.1).
I can ping the router. The router can ping the internet, do DNS resolution, etc.I have ensured routing is enabled. The only route I have configured is a default static route: 0.0.0.0 0.0.0.0 192.168.0.1.Oddly, if I choose 0.0.0.0 0.0.0.0 g0/0, I cannot ping sites on the internet from the router.
I tried setting up ip nat inside for my LAN and ip nat outside for the WAN/internet uplink, but this did not work.
This was the issue, I missed finishing the NAT setup.I can make the router ping out all day, and have my PCs ping the router, but getting the connection between the two is not working.
View 2 Replies
View Related
