Cisco WAN :: 40Gb Port-Channel Between 3750-x Switch Stacks?

Apr 9, 2012

I have a customer that would like a 40Gb port-channel between two 3750-x switch stacks.  When I try to activate four 10Gb ports in the channel, they go into error-disable.  However, I am able to create a 20Gb port-channel without issue.  I have had my configurations verified to Cisco best practice.
 
Is there a limitation on the amount of throughput that the 3750-x can handle?  According to the data sheet the 3750X-48T can handle 101.2mpps, based on two 10Gb uplinks so if my math is correct then a stack of two 3750X-48T should be able to handle 202.4mpps.
  
[URL]

View 3 Replies


ADVERTISEMENT

Cisco Switching/Routing :: How Many Port Channel Can Configured In Switch 3750 X

Apr 23, 2012

I would like to know how many port channel can i configured in the switch 3750 X ? and if there is a limitation by IOS ?

View 4 Replies View Related

Cisco WAN :: Load Balance Of 3750 Port Channel?

Jul 17, 2011

What is the load balance method of 3750 port channel ( by source ip , or by source mac ) to diver traffic to paths? I have tried to use 10.242.104.101 and 10.242.104.102 as source ip, it will travel to the same link (G0/1) within one port channel (G0/1+G0/2). Howerver, if I later use 10.242.104.109, then this time it will traffic to G0/2 link. What's the concept behind.

View 1 Replies View Related

Cisco Wireless :: Port Channel WLC 5508 And 3750?

Jan 2, 2013

I want to configure Port channel for WLC 5508 and cisco 3750 Stack Switch. What changes I need to make on WLC and where?

View 7 Replies View Related

Cisco Switching/Routing :: 3750 As A Port Channel Bridge?

Dec 7, 2011

I have 3750 core/distribution switches with routing enabled in two offices connected with copper link and L3 port channel interfaces. NewOffice#2 has moved about 5 miles farther away from office#1 and I have to deploy new core/distribution switch connect it to old core#2 via F.O and move all access switches with it. Old core will stay in old #2 offices as a bridge between office#1 and new office#2 Office#1core<->copper (Ethernet) <->oldoffice#2core<->f.o. <->new office#2core How I should configure port channels ports on oldoffice#2 core to act as bridge between office#1 core/dist and newoffice#2 core/dist without changing anything else (ip, etc) on whole network

View 1 Replies View Related

Cisco Switching/Routing :: 3750 - How To Setup Port-channel

Jan 22, 2012

I set up a port-channel trunk between a acess switch 3750 ( int gi2/0/1 and gi2/0/2) and Core 6509( int gi7/11 and gi7/12).
 
On the both the 3750& 6509 I configured:
 
interface Port-channel15
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 100,103
switchport mode trunk
 
But the ports on the core g7/11 and g7/12 keep shutdown and when I do show interfaces port-channel 15, it show the interface is shutdown.

View 6 Replies View Related

Cisco Switching/Routing :: Min-Link Configuration On 3750-X Port-channel

Feb 27, 2013

I am building a new network and intended on using the min-link feature on my port-channels between a 3750-X series switch and Nexus 4k.

However reading further into this it seems this feature is only supported on higher end models. I cannot find any reference to the min-links feature in the 3750-X configuration guide. Is this an available feature?

The 3750-X model is WS-C3750X-24T-L running IOS 12.2(55)SE3 IP Services

My thoughts is that the is only an LACP supported feature so I may not see the command until I have entered an LACP specific command on the port-channel but unfortunately I do not have a 3750X to verify this on at present.

View 0 Replies View Related

Cisco Switching/Routing :: Auto Qos Dropping Port Channel In 3750?

May 13, 2012

We have a switch that, when configuring auto qos on and edge port facing video equipment, the upstream port channel drops. I was wondering if no auto qos would have to be configured on the member ports of the port channel prior to enabling auto qos on any other ports. 

View 2 Replies View Related

Cisco Switching/Routing :: 3750 / Dual Trunks Between Stacks?

Jan 30, 2013

I have 2 3750 switch stacks which I would like to have redundant trunks between them.  This will provide two physical connections traveling through different geographical locations for redundancy in the event that a cable is severed.  I couldn't find anything in regards to setup/config.  Does it matter if I go stack1/switch1 to stack2/switch1 and stack1/switch2 to stack2/switch2 or should they cross to opposite switches like a stack cable?  I don't think that should be necessary, but couldn't find any documentation.  Should there be an issue with loops?

View 4 Replies View Related

Cisco Switching/Routing :: Configure Port-Channel Or Physical Interface On 3750

Jan 12, 2012

how to configure this. I did it in the past but kind of forgot how I did it.I have a stacked 3750 (two physical switches) connecting to a 2960.
 
I am creating trunk ports with limited access to VLAN 300, 600, and 700.
 
There is two interfaces connected from the 3750's(one on each physical stack member) to the 2960.I have the physical interfaces configured exactly the same.
 
3750 Config:
 
interface Port-channel2
!
 interface FastEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1, 300,600,700
switchport mode trunk
speed 100

[code]....

Should I keep the configuration on the physical ports and not configure the Port-Channel Interfaces? Do I need to configure port-channel load balancing? Is the channel-group mode sufficient? Goal is to basically create 2 links to the 2960 to double the bandwidth and provide redundancy.

View 7 Replies View Related

Cisco Switching/Routing :: 2960S Stacks / 3750 - EtherChannel Group Numbers?

Jan 27, 2012

I have a 3750 as core switch, adding 2 stacks of 2960S to connect. I want to establish etherchannel between the 3750 and each additonal 2960S stack, do the channel group numbers between the 3750 and the new 2960s have to match? 3750 has two channel-groups(1 and 2) already configured. Need to know,  I would create 2 additional channel groups (number 3,4) for each of the etherchannels between the 3 2960S Stacks and 3750? OR channel-group # is local to the device.

View 5 Replies View Related

Cisco Switching/Routing :: ME380x Port-channel From One Switch To Two Switches

May 8, 2013

I am trying to configure port-channel from one switch to two switchs, and only one interface of each switches make part of the port channel.Cisco IOS Software, ME380x Software (ME380x-UNIVERSALK9-M), Version 12.2(52)EY4, RELEASE SOFTWARE (fc1) [code]

View 5 Replies View Related

Cisco Firewall :: ASA 5520 - Connection To Multiple Switch Stacks

Nov 11, 2012

Currently in our environment we have have two buildings with an ASA 5520 in each and a core stack of 3750's in each building. I am currently working on a network segmentation project and am thinking of adding another stack of 3750's in each building to add more redundancy to our network. This will allow our access layer switches to have a trunk to each stack and prevent an outage if one of the links or stacks were to go down.
 
My question is how I would set this up on the ASA end of things while using a common subnet and HSRP on the 3750's. I understand how to use HSRP and STP on the switches to achieve this on the 3750 end of things. I saw you can do etherchannel on the ASA with 8.4 but how does that work in a failover situation?

View 2 Replies View Related

Cisco Switching/Routing :: Layer 3 Port Channel From 6500 VSS Switch To Two Standalone

Jul 30, 2012

Configured Layer 3 portchannel from 6500VSS enabled switch to two different 6500 standalone switch. Configured first ip on VSS switch, second ip on standalone switch1 and third IP on standalone switch2. My question is
 
1. Will the portchannel be up?
2. If port channel is up, will I able to ping the connected IP's.

View 1 Replies View Related

Cisco WAN :: 6500 Series Switch / Configured Port Channel On Both Switches With 2 Gig Interface

Jan 9, 2012

we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
 
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]

View 10 Replies View Related

Cisco Switching/Routing :: Configure Access Ports Into Port Channel On Nexus 7K Switch?

Feb 14, 2013

Can i configure access ports into port channel on Nexus 7K switch.If possible then provide the complete configuration.....

View 2 Replies View Related

Cisco Switching/Routing :: Standby Blade Switch 3030 Upstream Port-channel Flapping Up-down

Apr 30, 2012

show logging

May  1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May  1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May  1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May  1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May  1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May  1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May  1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
  
Configuration as below:

macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan

[code].....

Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.

View 2 Replies View Related

Cisco WAN :: QoS Configuration For 3750 Switch WAN Port?

Jul 27, 2011

We are using 3750 switches as WAN router facing the WAN cloud. To configure QoS for its WAN port, should I use 'auto qos voip trust" or treat it like a router port and configure class-maps, policy-maps, and attact service-policy input or output?
 
Because switches have different queuing and dropping methods than routers, auto qos can generate QoS configs that are considered most appropriate for 3750 switches. However the switch functions as WAN router. Maybe it should be configured using router type of QoS with policy-maps and service-policy?

View 9 Replies View Related

Cisco WAN :: 3750 - Stack And Switch Port Keeps Going Up / Down

Nov 7, 2012

I have 2 3750x switches connected via a pair of stackwise cables, but I keep seeing error messages about the stack&switch ports going up and down,Performance wise, it seems to work, but I'd like to eliminate this message... Sometimes it will go hours without bouncing, sometimes it does it a few times a minute....
  
*Mar  4 12:56:57.903: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state DOWN
*Mar  4 13:16:48.070: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 2 has changed to state UP
*Mar  4 13:16:49.093: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 2 has changed to state DOWN
*Mar  4 13:38:55.802: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state UP
*Mar  4 13:38:56.809: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state DOWN

[code]...

View 4 Replies View Related

Cisco WAN :: 3750-X POE Power Is Not Coming On Switch Port

Feb 22, 2013

We have configured Cisco 3750X POE  series switchs with Stack.WS-C3750X-48P each with Redundant 1100W & 715 W PSU's.  They are configured with Stack-Power in Sharing mode and the switches are Smart Stacked as well.IP Phone and Access points are connected its working in last two years,
 
Now we are facing some issue on Cisco IP Phone and Access point, When i have problem if unplug (disconnect & Reconnect) the IP Phone  from Switch port,Power is not comming on switch port.Plug it into another switchport of the same Switch it may not power in any port.I tried shut & no shut and reconfigured on switch port , I have verified  multiple switch ports same issue on the switch I have changed cable.

View 2 Replies View Related

Cisco Switching/Routing :: 3750 No MAC Address On Switch Port

Apr 15, 2012

There 's a Cisco IP phone that sits between a PC and the switch port. On the switch port, no MAC address is learned. However, the switch is able to detect the IP phone and deliver power to it: [code] Switch is Catalyst 3750 with IOS version  12.2(58)SE1.

View 1 Replies View Related

Cisco Switching/Routing :: 3750 Switch Stack-port Changes

Feb 7, 2011

I have a stack with a lot of stack-port changes, but on all the ports, how can I determine the faulty switch in the stack, cables are already verified. We did also a restart of the whole stack power off/on
 
running version
 
WS-C3750-48P       12.2(55)SE            C3750-IPBASEK9-M
 
This is the output after 6weeks
 
Switch#/  Stack   Neighbor   Cable    Link   Link   Sync      #         In  Port#     Port              Length    OK   Active   OK    Changes   Loopback          Status                                          To LinkOK          --------  ------  --------  --------  ----  ------  ----  ---------  --------  1/1     OK         4      1

[Code].....

View 7 Replies View Related

Cisco Switching/Routing :: Config Port Forwarding In 3750 Switch

Nov 6, 2012

I have a 3750 catlyst switch in my network and it is like a distubation switch,And for the nating and dhcp nomadix is using as gateway in the same network. for one of my local PC i need to config the port forwarding in 3750 switch. How to config the port forwarding on 3750 switch,

View 3 Replies View Related

Cisco Switching/Routing :: 3750 - Setup A Switch Port For 2 Vlans

Nov 8, 2011

I'm trying to setup a port on a catalyst 3750 so it will pass traffic for 2 vlans. It connects to a (watchguard) firewall which I've configured with a primary IP (for vlan 27) and a secondary IP (for vlan 29).
 
However I can't seem to find the correct commands to enter on the cisco switch port (I've tried a variety).
 
FYI the current configuration is...
interface FastEthernet1/0/38
description ## Connection to WG vlan27 and vlan 29 ##
switchport trunk encapsulation dot1q

[Code].....

View 8 Replies View Related

Cisco Switching/Routing :: QoS 3750 Switch Port Trust Without Resetting

Oct 7, 2012

We have QoS configured throughout the company, but the standard config we have applied across the 3750 switches only includes the below: We have IP phones (not cisco) attached that are marking with EF, and the PC is an untrusted end device (so needs to be by default marked as zero).Is the above enough to trust VOIP DSCP EF without resetting it to DSCP 0, or do I also need to add a trust line (i.e.: mls qos trust dscp)?

View 2 Replies View Related

Cisco Switching/Routing :: 3750 Populate All Switch Port With 100 Filter List

Oct 27, 2011

If i fully populate all switch port (Cisco 3750 series) with 100 filter list on each port is it recommendable.

View 4 Replies View Related

Cisco Switching/Routing :: Not Able To Ping Link Between 12-port 3750 Switch And ASR-9010

Apr 3, 2012

I have one 12-port 3750 switch having one gig connectivity with ASR-9010 router having IOS-XR. I am not able to ping this link with 9000 mtu size. I have enable system mtu jumbo on switch to 9000 and on ASR router interface mtu is set to 9114. At switch side switch interface is configured as a trunk port and one vlan has been passed on that interface. I am not able to ping the ip 172.16.10.2 with 9000 mtu size.

View 6 Replies View Related

Cisco Switching/Routing :: 3750 - Avaya Phone Switch Port Configuration

May 29, 2013

Since Avaya phones do not run CDP, how does the phone know which DHCP pool to pull from to get its IP address if the PC is connected to the phone.
 
Let's say I have a interface config like this 
interface gigabitethernet1/0/1
cisco3750(config-if)#switchport mode trunk
cisco3750(config-if)#switchport access vlan 126
[code]....
 
And two DHCP scopes configured on the switch. What keeps the phone from pulling from the wrong scope?

View 2 Replies View Related

Cisco Switching/Routing :: 3750-48 Port Switch - IP Route Added Not Showing Up

May 30, 2013

We have a cisco 3750-48 port switch.We have a few SVI's configured and some static routes configured.I had created a new interface vlan and gave it an IP. I can ping the gateway.
 
Now I want to add a static route to go out that interface.when I add: ip route 10.x.x.x 255.255.255.0 10.52.10.1
 
it eccepts it (no errors) But, it does not show in the routing table nor in the config? How to add the static route to go out that vlan interface.

View 15 Replies View Related

Cisco Switching/Routing :: 3750 Method Of Forcing Non Connected Switch Port LED To Blink

Jan 9, 2012

Any method of forcing a non connected switch port LED to blink for a certain number of times regardless if there is anything connected.The purpose of this is we have remote 3750 switch stacks and quite often have to tell non technical staff to patch to a certain port. It would be much easier if we could say "Connect it to the empty port which just started blinking orange" as the port numbers are difficult for them to see in these locations.A similar feature is available in the ethtool package for linux which makes it really easy for identifying ports on servers. It would be great if a similar feature is available on Cisco switches.

View 2 Replies View Related

Cisco Switching/Routing :: Difference Between Using Hsrp On Vlan And Physical Port On 3750 Switch

Nov 14, 2012

What the different between using hsrp on vlan interface and on physical port (routed port) on Cisco 3750 Switch? Wha the benefits?

View 3 Replies View Related

Cisco Switching/Routing :: 3750 - Change Port Numbering So Master Switch Gets GigabitEthernet1/0/x

Jul 18, 2012

I have 2 x 3750 stacked, the port number of the master switch is gigabitEthernet2/0/1, slave as gigabigEtherent1/0/1.
 
Can I change the port numbering so that the master switch gets GigabitEthernet1/0/x?

View 4 Replies View Related

Cisco Switching/Routing :: Replacing 3750 24 Port With 3750 48 Port?

May 21, 2012

We have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
 
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?

View 11 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved