I feel a bit in over my head here as I've never dealt with QoS stuff before, but what I'm trying to do can't be all that difficult. We are using a Cisco ASA 5505 appliance for routing/firewall.We are on a cable Internet connection with 3 MB upload.
On Sunday mornings, we send audio from a device on our network out over the Internet to a radio station which then broadcasts it, but we've had some jitter problems lately and would like to reserve some space for this audio feed to get out without other traffic getting in the way.
The device on our network sending the audio has IP address 192.168.0.22. The device's documentation states it uses TCP 9002 to send session data and UDP 9000 to send the audio data.
So, it seems to me I need to simply tell the firewall to give priority to the device at IP address 192.168.0.22, perhaps also specifying the ports and protocols. I'd rather not try to do this using command line stuff but will do what I need to.
Using the Cisco ASDM launcher to configure the ASA 5505, I created the following security policy but I'm thinking it may be incomplete, or perhaps the wrong thing altogether:
I created a "Source" called WLFJ_Tieline which is a network object with IP address 192.168.0.22.For "Destination" I just chose "any" to cover it all.For "Service" I don't know what I'm doing in that field. I see I can choose from things like TCP, UDP, IP, and also add port numbers, but I'm just not sure what I'm doing in there and chose IP.Then there is the "Source Service" field that I don't know if should be blank.
I am using ASA 5505 cisco firewall as a transparent firewall. I have assigned ethernet 0/0 as outside interface and ethernet0/1-7 as inside interface. There are 3 departments in office. So, i connected ethernet 0/1 to Dept A, ethernet 0/2 to Dept B and ethernet 0/3 to Dept C. Now, I want to limit bandwidth to each department, e.g, 1 Mbps download/upload to Dept A, 512 kbps download/upload to Dept B and 512 kbps download/upload to Dept C. So, how can i do this in ASA 5505.?
I have 20 mbps internet link and I have ASA 5505 . I have to divide this bandwidth 10-10 mbps each for Voice and Data . So that both can work properly. because when I am using it for both on same interface, I am getting Voice disturbance..
We have 10MB dedicated Internet BW and want to run VC device and due to heavy traffic and BW high utilization at peak hours, VC performance is not sufficient. We would like to reserve 2MB for VC device. How much possible to fix up this configuration in ASA5505 version disk0:/asa724-k8.bin [URL]
When I have a computer directly connected to the Cable Modem I get 9.84MB Down and 1MB Up. When I put it behind the ASA 5505 with policing on the interface, I only get 4MB Down and 660Kb Down.What I'm wanting to do is setup this up to enable my VoIP to have a higher priority and shave 128kon both the Up/Down for the VoIP traffic. I also want to make sure I don't exceed the inbound and outbound thresholds.I''m using a 5505 Security Plus?
I'm having a bit trouble to limit the bandwidth on outgoing traffic with a Cisco ASA 5505.
In my case I want to limit the bandwidth to 31mbit/s up and down on the outside interface. but with my current configuration, just the download rate gets limited to 31mbit/s when I do a tptest. and the upload is around 40/50mbit.
Here is the policy configuration,
access-list outside_bw extended permit ip any any class-map outside_bw match access-list outside_bw
We currently have a tunnel configured between 2 ASAs
1- Is it possible to assign 1.5 Mbits of Bandwidth(BW) to this tunnel?. Then if Tunnel number 2 is configured I could assign 2 Mbits to that one for example?
I am not referring to prioritizing certain type of traffic over the IPsec tunnel, I am referring to Tunnel 1 has 1.5 Mbits of BW guaranteed for all traffic that goes thru it. Same for tunnel 2
Then
2- How to monitor the amount of BW in an IPsec tunnel?
Can I do either of the following with a Cisco 5505? Limit Internet bandwidth used by the tunnel so it doesn’t consume our entire Internet bandwidth of 10Mbps at any given timeLimit Internet bandwidth used by any single host for same reason I have a site-to-site VPN configured to another Cisco asa.
I've got an HP Printer which supports ePrint, which is very useful for me because I always need to print stuff, especially when i'm at college.The only problem is: we've got almost 200 people on the same network here. And I don't want radom trolls to just be able to print with my printer. (The printer has a direct wired connection to the network)
Someone told me the commands, but I can't remember them. Have a router (2801) at the end of a highly utilized T1 link/router. How do I protect it so my SSH and/or Telnet sessions will get serviced if the router is real busy.
We are a non-profit organization that is heavily reliant on interns that use their own laptops a lot here. My concern is they come in and connect to our wireless network with no supervision or anything else. I am worried they will introduce a virus, trojan, or something to our network. What the best way to keep them from introducing unwanted malware from a thumb drive, virus in email, or something to that effect shy of standing over them while they install and run an antivirus software?
We bought two packs of IPCAM online from a vendor named HooToo, who seems have different online sites for selling various surveillance cameras. What we purchased is a unit with model no. of HT-IP206, according to its advertisement it has a storage temperature as low as minus 10 degree, and adversely high up to 60degree. While on the other hand, it states that the operating temperature shall be strictly between zero and 55degree. What Im concerned is that what if temperature drops down to minus when a camera is fully operating? Shall extra heating system be needed while the real temperature fails to meet the above-said requirement?
At the school I live in various sites are blocked so I need to use a proxy to access them. Is there any way that someone could steal my password or something while I use one? Also, let's say that I use a proxy in one web browser (let's say Opera) to view a blocked site, but then use a different browser (Firefox) with my normal IP, would I be able to use Firefox with no worries if I need to check something like my bank account? Basically, can you restrict them to one program so you can use personal information on one and normal browsing on the other?
Right now mine isn't PW protected, but I think I'm going to do that. Anyway, my question is, if I change my router settings and make it PW protected will I have to type that in every time I turn on my computer to get access to the internet?
I just installed a new Synology DS212j NAS behind an old Belkin F5D7230-4 wireless router (probably from 2006) on my home network. The wifi network uses WPA-TKIP with a strong password but otherwise has no security. The NAS is connected to the router with cat5. The NAS is setup with a couple password-protected shares (accounts setup on the NAS) that the Windows 7 PCs on the wifi network can access.
Since the NAS and router will be on 24/7, what else do I need to do to ensure that the NAS is secure?
I went through the install procedure outlined in the ProtectLink Gateway install manual and i activated the ProtectLink Web product through Trend Micro (which shows up through their web site as a registered product to me). It still doesn't show up as installed on the SA540 (under Administration/License Management screen). When I try to activate the product again, it shows as "Already registered". Trend has no idea why it won't work. They said Cisco sold the license, so try their support.
I will try to explain my problem as clear as possible but my knowledge about networks and routers is very limited.
I have a DIR-615 version:C1 firmware:3.13NA My ISP is ATT DSL Modem is Siemens SpeedStream 4100, it does not have a router built in Internet line is connected from wall to modem, to router, to PC.
after I upgraded the firmware I had no internet coming out of the router, I bypassed the router and connected straight to the PC and I got internet. I unplugged the power on both modem and router waited a whole night (I was too tired) and in the morning internet was back to PC and I had WIFI again BUT. When I put a password on the WIFI network all my stuff finds the signal but cannot connect, if I open the signal meaning if I have no password and the WIFI is open I can connect all of my electronics without any problems.
I already tried using WEP and WPA but still unable to connect anything, I been leaving my signal open when I'm at home for the last week and I don't like it.
Before the update everything worked fine.
I don't know if this matters but I have a PS3, Wii, Roku box, Laptop and a couple cell phones connected to it. And there are like 6 or 7 network signals close to my house.
I have a Cisco RV082 that doesn't appear to filter any selected categories. To run through what i've done so far, within the 'Web Protection' screen i've: enabled URL filteringconfigured a number of categories to filter by putting a tick in the repective business hours boxset the business days to 7 days a weekspecified business time as 24hrshit the save button.
My licence appears as activated and my platform shows as "gateway service".I've gone on to a number of machines and all are able to access websites that fall under my blocked category (facebook for example even though i've blocked the social networking category).
I use to be running on firmware 1.0.2.4 with ProtectLink-Web working great, but then it expired. Some time later I updated the router to 1.0.4.17 and purchased a three year subscription to ProtectLink-Web, followed the registration link on the router, obtained an activation code, followed the activation link on the router and activated the service, however it didn't activate on the router.
I try to activate again and Trend Micro's site just says that it's already been activated. I contacted Trend Micro support and they see the activation attempts on there end and they said everything should be working. They recommended a factory reset which I performed and then attempted activation again, and again their site says that the service has already been activated. And yet when I go to Cisco ProtectLink Web > License > Summary it just says: "Please activate ProtectLink License to display the license information" and wont allow me to access the features. What is going on? Could the firewall be blocking the service? I didn't have this trouble the first time I used ProtectLink with f/w 1.0.2.4
How to protect shared folders to denie access from server???i am really in need of a software where i can share files on network but i don't want the system administrator to access those files.
I have an asus wireless router the router lost connection for a few days and when Internet came back there was no password to protect Internet and was just basically open access. The computer which all the Internet setting are on went away for repair. When the man brought it back after backing up the computer I asked him to put the password back on the Internet. This he has done. We entered the new passwords on our iPhones and they connected and worked no problem. Then we tried to do it with our laptops but they won't connect. Phoned the bloke back he said we had to get the laptops to forget all the old settings for the router and it would on take five minutes but he never told us how to do it.
I am trying to password protect my router but when I go into wireless> security mode and click on WPA or any of the other choices it goes back to disabled.
I rexently bought a EA6500 to controll when and how much my children should access internett. Even before I have installed it my son have downloaded a program called Netcut, who hacks innto the router and take controll over the access and the prioritation of computers on the network. Is there any way I can block such software to access my router. I had a livechat with Linksys, and they claimed that the router have no capability to block programs. I also tried to download "Netcut Defender" but my AVG warned me about a worm/virus in the download, so i aborted the operation
My router has been in use for some time. WRT54G. I did the set up from the disc and instructions and it's been no problems. I would now like to add a password to log on to it from a wireless computer such as my laptop or the other household computer.
I got an Linksys WRT54GL-DE and my problem is,that someone manipulates the router.Is there any chance to protect the router in that way,that is not possible to reset the router by using the Reset-ButtonNOR by the Linksys software-tool?Especially the software-tool is the problem - I am afraid,that somebody reset / manipulate the router by using the software.
We are finding the price for ASA 5505 to high and our clients are having problem securing budgets for these devices. We don't want to move to different vendors and we have a team of people we already know Cisco well.I have seen Cisco router 877 which have the ipadvance ios, is this the same as the ASA5505.We would like to offer our clients an alternative to ASA5505, but something which can do the same as a edge device but also protect the client from malicious attacks and has CLI.
My rv082 router protect link gateway is already activated. How do i change the key or activate it with a new activation key?The router dont have any link to change the key. I'm using v1-2 rv082
I have a Netgear router which feeds an Eugenius ecb3500 Wireless Access point. I did not install the access point. I need to password protect our wireless environment, and that needs to be done on the Engenius. However, though I have tried many ways to access that device, I cannot. I cannot get an IP address for it,either. When I plug it directly in to my laptop (Win7), and type in the command line ipconfig, I get the IPv4 addresses of my laptop's local and wireless LAN card. How to get into the Engenius access point and password protect it?
