I have spent a day trying to get the console / AUX port of an 887 to answer a call in (simple modem on aux port for remote configuration)
I believe that all i need on the line con 0 is "modem enable" and then i should configure line aux 0 as normal.
We just installed a hosted VOIP system using Cisco 7900 series IP phones. We are having a strange issue with a few computers where they pull DHCP information from our VOIP provider's DHCP server on the Internet and not our LAN DHCP server.
The switchports areconfigured as: switchport mode access
My rationale behind this is that the phones would use CDP to get their VLAN info from the providers Cisco router and the PCs would just ride on the default VLAN. But this is not the case. Computers randomly keep getting DHCP info from the provider's router. Do I have to use voice vlan x and make the switchports trunks?
I've read some conflicting things on the new 2504 WLC's. Some things indicate all 4 ports are fully useable, while others indicate perhaps only 1 or 2. I think I've read in product documentation that it support a max of two ap-manager interfaces. Does, for sure, all 4 ports are useable? I'm thinking of the following configuration:
Port 1: management interface and first ap-manager interface
Port 2: second ap-manager interface
Port 3: first dynamic/client interface
Port 4: second dynamic/client interface
I'm planning on deploying my ap's in h-reap mode with a max of 25 ap's per 2504. Since I'm using h-reap, bandwidth shouldn't be much of an issue so I'm also considering trimming it down to using just two physical ports as follows so I can take up fewer gig switchports which are scarce at many of my locations:
Port 1: management interface and first ap-manager interface
Port 2: first and second dynamic/client interface
I've always deployed 4400's and 5508's with LAG so I haven't had to think about this much until now.
I am switching out our old WRVS4400 router to the Cisco 891. Having a problem configuring the Cisco 891 router. I changed the V LAN port on the 891 from 10.10.10.1 to 192.168.2.1 and the ip address saves but when I try to rediscover it through the CCP to the new Ip address 192.168.2.1 I get the message discovery failed.
The sub net mask I used is 255.255.255.0 The only thing connected to the 891 router is our linksys 48 port switch which is SL248G and my laptop is connected to the switch. The port its connected to is FE LAN 0 . How do discover the 891 so I can do further configuration and to enable the FE8 port for using it for our internet connection?
interface GigabitEthernet0/0
ip address x.x.x.36 255.255.255.248
ip nat outside
ip virtual-reassembly in
no ip route-cache
duplex auto
speed auto
no cdp enable
[Code]
ip nat inside source static tcp 192.168.1.252 22 x.x.x.36 6922 extendable
ip route 0.0.0.0 0.0.0.0 x.x.x.33
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit any
Anything wrong with my config? port forwarding to my ssh wont work. Im using CISCO 1900 Series.
I'm having troubles setting up a separate VLAN for wireless on a SG-200-26. My first question is why did Cisco not make the VLAN setup like they have all their other business class switches? Anyways, the Access and General modes on these SG class switches are throwing me for a loop.
Right now I just have one port (g10) on the SG-200 switch that needs to be in VLAN 6, which is our wireless VLAN. All other ports are in their default VLAN, which is 1.
Here's what I've done...
Configured port G1 (trunk to another switch) as the trunk port and Port G10 (attached to WAP) as a general port. All other ports stayed in their default configuration. This is what it looks like now...
Port Mode PVID Operational VLANs
g1 Trunk 1 1U, 6T
g2 Trunk 1 1U
[Code].....
I'm pretty sure port G1 is configured correctly, but I have no idea about what port g10 should look like. Common sense tells me it should be an Access port and assign it to VLAN 6, but apparently you cannot tag the traffic within an Access port on SG switches, which makes it useless because how will other switches recognize what VLAN the packets are in? So the next logical mode would be General mode, which I put in VLAN 6. I switched that port from being 6U (untagged) to 6T (tagged), but neither seemed to work.
VLANs on SG switches, how port g10 should be configured for VLAN 6 traffic.
We are using 3750 switches as WAN router facing the WAN cloud. To configure QoS for its WAN port, should I use 'auto qos voip trust" or treat it like a router port and configure class-maps, policy-maps, and attact service-policy input or output?
Because switches have different queuing and dropping methods than routers, auto qos can generate QoS configs that are considered most appropriate for 3750 switches. However the switch functions as WAN router. Maybe it should be configured using router type of QoS with policy-maps and service-policy?
I have worked on cisco switches only..I want to configure nortel5510 have configured vlan.but Switch Ip address is changing when I am giving ip address to port. and i cant see port ip configuration in show runn also i want to configure loopback.I am configuring switch ip address 192.168.123.1/24 but when I give ip address to port 192.168.120.17/29(PORT IN DEFAULT VLAN) switch ip address changes automatically.I have port 1-4 configured in vlan 1 other ports are in L3 vlan.I want see port ip address details Like we see in cisco (SHOW IP INTERFACE BRIEF ) what is command in NORTEL??
View 2 Replies View Relatedhow to 24 port networking switch configuration
View 1 Replies View RelatedI have an ADSL connection which I would like to have my Cisco Soho 97 ADSL router configured to dialup and forward to port 8080.
My network is 192.168.1.0/24
Router is 192.168.1.1
Server is 192.168.1.4 - Default gateway is 192.168.1.1
I am able to connect using the script below and get a public ip address but i cant get it to connect to the internet?what command to use for port forwarding to 8080?
hostname Router
!
!
ip subnet-zero
ip name-server 212.23.8.1
ip name-server 212.23.3.1
ip dhcp excluded-address 192.168.1.1
[code]...
I've configured port forwarding on an ASA 5505 to connect to an Access Point web administration.This Is for testing purposes only. I've followed the guidelines for port forwarding and I've created an access list but I can't connect to the AP.I know It's working because It connects fine when connected to my speedtouch router.I've attached a running-config.I'm getting hit counts on the ACL and I'm getting untranslate_hits on the nat but no translate hits.
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
!
[code]......
i am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration
View 1 Replies View RelatedI have recently replaced an RV082 router that had failed with a new RV082. The previous router was set up to forward port 443 ssl requests to a server in the network. Worked flawlessly for years and that is why I replaced it with same model. The new router is also set up to forward port 443 ssl requests to the new server. The issue is that the router responds with its own certificate and does not forward the request to the server.
View 5 Replies View RelatedI recently configured CISCO 3310 box with MSE version 7.2. Services are up and running in the box, I could add the MSE to WCS and also able to track the location using WCS. However, I could not connect the third party software to MSE web services to get the location information there. When I hit the server url "https://<my mse>" I get list of possible services like:
Error 404 - Not Found.No service matched or handled this request.
Known services are:
http://my server:8880/hs/
http://my server:8880/mdp/
http://my server:8880/admin/
[code]....
I browsed through the documentation (CAS_71.pdf) and found a text saying:
Note Port 80 will be enabled on the MSE if the enable HTTP command was entered on MSE. Ports 8880 and 8843 will be closed on the MSE when the CA-issued certificates are installed on the MSE. I am running the test system so I do not really want to install CA signed certificate, so I used self signed certificate and restarted the server, but it did not work.
I have an RV082 V2 with 2.0.2.01-tm and I am having trouble with getting my Sprint Airvana to connect properly to the mobile service. I've read on the Sprint forums indicate putting the Airvana in the DMZ generally allows the device to work properly; however, none have the RV series routers for tips on how to do this appropriately. This device used to work fine behind the RV082, but I reset it one day and it no longer works.
The Airvana is a femtocell/router device with a WAN port and 3 LAN ports. If I connect the Airvana directly to my cable modem, I get the appropriate connection and can then make calls through the device instead of through the Sprint connection; I live in a basement unit and get crappy signal without the device. This proves the device works and that my ISP is not blocking the ports. Sprint indicates the device uses UDP 53, 67, 68, 500 and 4500. Their support sucks and they insist I put the Airvana before my router. I absolutely do not want to use the Airvana as the router. There are almost no configuration options in the router interface and it needs to be rebooted somewhat regularly, which would drop internet access throughout the house for 10-15 minutes while it reboots and finally establishes an internet connection.
As soon as put the Airvana behind the RV082, I no longer get the appropriate connection. I can, however, plug my computer into one of the LAN ports on the Airvana and connect to the internet in general. I have the router assign a static IP to the Airvana, and tried forwarding the required UDP ports to the IP. This did not fix the problem.
I can certainly troubleshoot the port forwarding issues, but I would also like to look into putting the device into the DMZ, if possible. I've not worked much in this area, so I am unsure how to appropriately configure the router to allow this to happen. Is it possible to have the Airvana in the router DMZ without having a public IP for the device itself?
I have an issue/doubt regarding the configuration of a modem + router. The modem is a netopia-3000 (who care ) and the router is a netgear WGR614V9, The first has the address 192.168.1.1, the second 192.168.0.1 My pc in dhcp take the address from the router (192.168.0.x) and internet work, but if I set the ip manually 192.168.1.x it stop to work, why?
View 1 Replies View RelatedI want to port forward, so i can broadcast using icecast but it requires me to access my router. I follow the steps from Setting a Static IP Address in Windows 7 - PortForward.com but from step 4 where i have to access my router in my browser,i write my ip which is: 10.0.0.4 according to cmd, and i just get a "Oops! Google Chrome could not connect to 10.0.0.4" message.I have attached a picture showing info from my cmd. It's in danish but i don't think that should be a problem.
View 3 Replies View RelatedI'm trying to configure cisco 1811 with dual isp internet connections. Everything is working fine till i get to setting up port forwards.The port forwards for 2nd ISP do not work while connection to 1st isp is active. If if shutdown the connection to isp1 the port forwards work fine.
here's relevant section of the config
Code:
track 123 ip sla 1 reachability
delay down 15 up 10
!
track 456 ip sla 2 reachability
delay down 15 up 10
[code]....
I can access the 192.168.2.131 web server using the ISP1 ip but not ISP2 ip If i shutdown ISP1 interface the server becomes accessible through ISP2.Also while ISP1 is active I can't remote desktop to 192.168.1.210There are no acls, firewall zones or anything else.
I am connecting two catalyst 3500 XL switches via fiber fx ports for layer 2 connectivity. Do I need to configure anything in the IOS or do I just plug in the fiber?
What needs to be configured?
I have found some samples on the FlexConnect setup for the controller side. However none of the documents mentioned how the switch port should be configured that goes to the controller and AP.
At this moment I have a Cisco 5508 configured in CAPWAP mode with 20 APs. I would like to use same controller for connecting one of the remote sites with 2 APs in FlexConnect mode. Current the 5508 to switch port is configured as 802.1Q port. All CAPWAP AP ports are configured as "switchport access vlan X" where X=capwap VLAN. Need to know how the switch port should be set for the remote site where flexconnect APs connect.
I'm trying to configure a mirror port on a 3750. This configuration needs to replicate data from local ports, but I need that also act as a regular access port.
With the initial configuration, SPAN port, there is no problem, all the data of the configurated ports is replicating in the configurated port. On the port configurated as mirror there is a PC connected for audio recording. When the port is not operating as SPAN there is communications without problem over the LAN. But when I configure the port as SPAN, communication is interrupted.
Here is the actual configuration:
SWITCH1-PISO7#sh monitor session 1
Session 1
---------
Type : Local Session
[Code]......
I have an old Cabletron switch i have used for about 8-10 years, it has some vlans set up and i was wondering how i can "talk" to the switch and set it up. I am using this switch in my home on my vast network. is it possible to "reset to factory" or anything without a serial cable? I would like to use snmp of telnet to configure but i dont think it has an ip set up and it is such an old switch I cannot find any info from entrasys.
View 1 Replies View RelatedI was changing the port forwarding configuration when suddenly the router stopped working, and now the "D-Link" light is constantly on, and the power light and the 4 LAN lights are flashing. Nothing worked, resetting, or unplug and plug again in a short time.
I disconnected it for 12 hours, and when I plugged in again, it kinda worked, and the settings where factory defaults, so when I tried to connect it to DSL via PPoE, when ( I believe ) it reboots to accept the changes, it starting flashing again and completely stopped working.
So I waited 12 hours more unplugged, plugged it and it worked, and the setting from 12 hours earlier were still there. But when trying to connect to the DSL it stopped working AGAIN.
Now I don't know what to do. I guess I am going to keep trying connecting with little differences, until something.
I believe it still has warranty but since the is no official service in Uruguay, it isn't economically viable to send it overseas.
I am currently connected directly to the DSL, sharing connection to other computers through a switch and hosting an ad-hoc wireless network, but the performance is terrible and the wireless range is minimal.
I am building a new network and intended on using the min-link feature on my port-channels between a 3750-X series switch and Nexus 4k.
However reading further into this it seems this feature is only supported on higher end models. I cannot find any reference to the min-links feature in the 3750-X configuration guide. Is this an available feature?
The 3750-X model is WS-C3750X-24T-L running IOS 12.2(55)SE3 IP Services
My thoughts is that the is only an LACP supported feature so I may not see the command until I have entered an LACP specific command on the port-channel but unfortunately I do not have a 3750X to verify this on at present.
I have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.
View 1 Replies View RelatedI have a pair of 6500's setup with VSS and there is currently only one link between then. However one end of the link is on Po10 and the other end is on Po25. If I move the Po25 over to Po10, will things break? It seems to be working fine now. I'm about to add a second link and I'm concerned about the current configuration. It makes more sense to me to have both ends of the same link on the same port-channel ID. I've seen documentation which states otherwise however.
interface Port-channel10
no switchport
no ip address
[Code]....
I have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
I vave a zyxel p-660HW-T1 v2.I need to do PORT FORWARDING since I want to use an IP Camera in order to have remote access to video.I do not find PORT FORWARDING in the modem configuration. I find NAT, but not port forwarding.
View 1 Replies View RelatedI read quite a few documents on configuring SPAN on a cisco switch but none of them mention any limitations or any kind of CPU load it can have on a switch. I need to configure this on one of our switches and would like to know if there are any implications related to SPAN.
View 5 Replies View RelatedI have connected a 10BaseT device to a CISCO Catalyst 3560xPOE switch with dynamic port security. All seems to work fine when the distance between the two devices is closer then 200ft. When I connect to 10BaseT devices farther out near 300ft the response from the attached device is lost. It works ok on unmanaged switches at the longer distance. Is there a minimum response time from attached devices for dynamic port security to work properly? Is there any other explanation why it would work on cheaper switches, but not on the Port Secured Switch?
View 2 Replies View RelatedI have a 6500 switch and i recently removed a module (line card) from the switch. The problem is that the port configurations of the removed module still exhists in running configuration. I was not aware of the right procedure,[URL] however, i would like to know whether it resolves if i reboot the switch.
View 1 Replies View Related We have a 24 port and 48 port 3560 E switches with identical IOS the 48 port switch supports private vlan while 24 port switch doesnt
configure private vlans on 24 ports 3560e and is it best practise to configure private vlan on this platform(3560)?
IOS version : C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
flash:/c3560e-universalk9-mz.122-55.SE3/c3560e-universalk9-mz.122-55.SE3.bin
Since Avaya phones do not run CDP, how does the phone know which DHCP pool to pull from to get its IP address if the PC is connected to the phone.
Let's say I have a interface config like this
interface gigabitethernet1/0/1
cisco3750(config-if)#switchport mode trunk
cisco3750(config-if)#switchport access vlan 126
[code]....
And two DHCP scopes configured on the switch. What keeps the phone from pulling from the wrong scope?
