Have a problem in config of my ASA5505 --> I can't access Internet from my new created vlan number 4 (Vlan4):
here my config:
ASA Version 8.4(1)
!
hostname FWWIB1
enable password OEIOH8Zv/vNvif8C encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
I have the following config below on my ASA5505, where I want to be able to access remote computers who are VPN'd into the inside network, for support purposes.I want to be able to ping the VPN ip from the LAN, and be able to connect to these computers via the VPN ip. [code]
View 4 Replies View RelatedI have an issue accessing the inside network of my church from VPN. This only happens when I connect from my home network. I have no problem accessing inside network of my church if I'm connected from else where (my Clear Hotspot or someone else's house). Here is the hardware detail:
At the church, we are using Cisco ASA 5510 and we have so many VPN tunnels to different churches. At home, I 'm using Cisco ASA 5505. See that attached configuration for my home ASA5505.
I'm trying to make a very plain and simple network with the ASA 5505, I've strated from scratch over a dozen times triyng to find where I'm going wrong. My main goal is to simply create an IPSec VPN connection to my ASA 5505 and simply ping and connect to devices with the "inside network", so far I can easily create and establish a IPSec VPN Connection, but up to this point, I cannot successfully ping or access a single device on the ASA 5505 inside network.I've taken, create the IPSec profile with the ASDM wizard, add exemption for the VPN IP Pool, add access-list from this Cisco link, url...All this and I can't make a single connection to the inside network. [code]
View 7 Replies View RelatedUsing an ASA5505, have 1 static outside address, want to access an inside SBS-Server on SMTP, RDP (3389), HTTPS and port 987
Have configured network object nat rules using the asdm, SMTP works (I can telnet to the server on port 25 from outside), however for some reason I can not telnet inside and out on port 25, so outgoing mail does not work. RDP does not seem to work from outside, 987 I havent tested from outside. When I try to create a network object nat rule for https I get this message from the ASA:
[OK] object network SBS-HTTPS
object network SBS-HTTPS
[ERROR] nat (inside,outside) static interface service tcp https https
NAT unable to reserve ports.
I am using ASA 5505 firewall with base-license. I connected my firewall to one cisco 3750 switch where i created 5 vlans. I done NATing for all vlans and they able to get internet and working fine. They able to browse all internet sites like gmail and yahoo mail.
All internal users are configured to use Outlook for their webmail. Here the problem is with outlook they are unable to send and receive the mails.
If they directly connected their system using public ip( Directly from ISP) they able to send and receive mails from outlook.
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedI currently have an out of the box ASA5505 and need to change the internal interfact from 192.168.1.1 to 10.20.3.1 so it fits in with the rest of the network.Tried using the ASDM Startup wizard (via 192.168.1.1) and it just seems to hang on "delivering the commands to the device".
View 16 Replies View Relatedi have cisco asa 5505 Security adaptive firewall. my inside network is 192.168.1.0 255.255.255.0 . i want to add static route another network i have that network id is 192.168.2.0 . 255.255.255.0.how i can add the route.
View 9 Replies View RelatedI am very new to Cisco ASA and I am trying many days to implement the design below but still cannot get it done. The situation I am facing is
- a host (e.g. 192.168.5.10) under Inside interface can contact to outside without any problem.
- however a host outside (e.g. in VLAN1 or outside this network) cannot contact host under Inside interface. I am using PING test and always get Request Time Out. [code]
I have an ASA 5505 with 3 host license.I want to configure 2 outside interfaces and have inside interface. The outside interface going to a separate ISP.Will this work or do I need more licences?
View 3 Replies View RelatedLet me start by saying that I'm just starting to study for CCNA, so the ASA seems to be a bit above me yet. The ASA's we are using is for VPN to our corporate office and only allowing access to our Citrix environment, so no direct internet allowed. We have a person who works in the remote office who has need for a caption telephone that requires direct access to the internet. The phone only supports DHCP, and getting the ASA to do an ARP reservations is proving difficult. For now I wrote an access list to allow it's DHCP address out but it still isn't working. The access list I wrote is:
access-list 101 extended permit ip host xxx.xxx.xxx.124 any log
access-list 101 extended permit ip any any
access-group 101 out interface outside
When I do a show access-list I'm seeing that traffic is hitting the access list as the hit counter has increased. When I do a show conn I'm seeing one of the IP's that the phone should have access to, however the flags are: saA, so I'm assuming they are not getting a response. According to the manufacturer, only outbound connections are needed, no incoming ports required. All traffic is TCP.
The ASA5505 I am working with has this from the show version:
Licensed features for this platform:Maximum Physical Interfaces : 8VLANs : 3, DMZ Restricted Inside Hosts : 10Failover : Disabled VPN -DES : EnabledVPN-3DES-AES : Enabled VPN Peers : 10WebVPN Peers : 2Dual ISPs : Disabled VLAN Trunk Ports : 0
This platform has a Base license.
Does the Insides Hosts :10 line mean that only 10 devices can be connected to the firewall at one time? I would like to connect an AP to one of the PoE ports and have possibly more than 10 connected. Is this possible with this ASA5505?
I just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
I have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
I have ASA5505 configured with internal network as 192.168.15.0 and default gateway 192.168.15.1 From the inside network, i'm able to access internet and able to ping all website (enabled ping). and all internel network devices can ping each other. Except i cannot ping my gateway (ASA5505) 192.168.15.1. I'm continously seeing this message on the log, when i tried to ping.. How to fix this?
Denied ICMP type=8, code=0 from 192.168.15.xxx on interface inside
replace xxx with my network devices that try to ping the gateway..I dont want outsiders ping my gateway, i need ping for inside internal network only.
I want to upgrade "inside hosts" from 10 to unlimited on a ASA5505-BUN-K9, Do I have to buy Security Plus license ( L-ASA5505-SEC-PL =) ) before activating ASA5505-SW-10-UL ?
View 3 Replies View RelatedThe ASA device is going to be the gateway for multiple distinct inside IP subnets. We can have have a unique outside IP address to correspond to each inside IP subnet if needed, but we need some means for a VPN client or a site-to-site VPN to have acess to a pre-definied IP subnet (i.e. if customer A establishes a VPN connection, they have connectivity to IP subnet X; customer B establishes a VPN connection, they have connectivity to IP subnet Y, etc.).Currently, the two inside IP subnets are 10.10.0.0/16 and 10.20.0.0/16. We will be adding more.The problem we are facing is that we cannot reach the VLAN 201 from the ASA we believe this is because. I have setup two addresses on port 0/1 Vlan1, 10.10.20.2 and 10.20.20.1 as an alias. How can we make traffic for the 10.10.0.0/16 subnet untagged and traffic for the 10.20.0.0/16 subnet tagged for VLAN 201.
View 1 Replies View RelatedI have installed ASA5505 in the network. Port forwarding has been done for one of the server in our LAN. Public users are able to access the server successfully. I am trying to access from inside using the same Public server IP, but unable to access it. Can I have this feature in ASA5505(I think it is loopback configuration). If so, may I know the configuration detail?
View 4 Replies View RelatedI have been working on a configuration for single IP address (on outside ) of ASA5505.I am trying to utilize the outside address 192.168.0.249 to PAT/NAPT to 10 inside machines [code]
What I am not sure of (actually that could be considered all encompassing) is the mapped services/real services.Any constructive comments assistance?
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedI am trying to make the multicast working between few hosts inside a single vlan. Host are running mysql cluster and Multicast is used to send master/slave status information to the IP 228.10.10.10 on port 45566.The vlan is defined in FWSM and the host are connected via the core-switch(6513). (hosts-->core-sws--->fwsm)I have tried searching the documentation, but couldn't find specific info to enable multicast between hosts residing in same vlan. FWSM is running code 3.1(4). since the hosts are residing in the same vlan, I am thinking of applying the <multicast-routing> just for that SVI in FWSM.
View 6 Replies View RelatedI want to know what is the best way to black traffic inside the same VLAN, this VLAN is a user VLAN, it means that I am talking about access layer.I wanted to use private vlan, but C2960S doesn't support this feature. Any other way to prevent any to any traffic in the user vlan, this vlan only have to speak at the Layer 3.
View 2 Replies View Relatedi have several cisco 3500XL switches with trunking. I created a VLAN lets say 20 which purpose is for wireless clients. I installed wireless controller with 4 APs and controllers sees all 4 APs. Controller is also DCHP server. When wireless client authenticates it's DCHP requests in not getting to DHCP server (controller). If i connect all equipment in non managed switch everything works.
View 10 Replies View RelatedShort version is we cannot communicate between our subnets.We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc)We have PAT for each subnet to our outside interface. Each subnet NATs out properly currently.I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS.What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces?
View 0 Replies View Relatedmy environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12
name NextVLAN
state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
I'm having an issue routing between vlans. I have vlan 1, and 2. I want to ping something on vlan 2, from vlan 1. I cannot ping from a computer on vlan 1 to a computer on vlan 2. I can ping each computer from the ASA 5505. I get an error on the ASA when I try to ping from the computers. The error is Failed to locate egress interface for UDP from voice:192.168.0.199/137 to 192.168.1.200/137. I can't understand why it even mentions IP 192.168. 1.200/ 137... I reset the unit configuring it from scratch and still no go. I have no given a static route to the out yet.. I need to get inter-vlan routing working first. [code]
View 13 Replies View RelatedI have 2 questions.Om my cisco 2811 (IOS 12.4(15) T9 IPBASE W/O Crypto) i am using 3 interfaces.And i have a pool of Global addresses: 200.x.z.97-200.x.z.126 255.255.255.0
FastEthernet 0/1 description WAN interfaceip nat outsideip address 200.x.y.253 255.255.255.0
GigabitInterface 0/2/0description DMZ interfaceip nat insideip address 10.0.0.1 255.255.255.0
GigabitInterface 0/3/0description LAN interfaceip nat insideip address 192.168.0.251 255.255.255.0
[Code]....
configuration of my ASA 5590 i am trying to give access to tcp ports 50,000 to 60,000 from DMZ to Inside interface
View 2 Replies View RelatedA Cisco ASA running 8.2.5 with 3 interfaces: Outside (Sec lvl 0)/-nternet IP / DMZ (Sec lvl 2)-192.168.8.0/24 / Inside (Sec level 100)-192.168.1.0/24
An ACL on the DMZ which looks like this:
access list DMZ_IN permit ip 192.168.8.0 255.255.255.0 any
access list DMZ_IN deny ip any any
access-group DMZ_IN in interface DMZ
global (outside) 1 interface
nat (DMZ) 1 192.168.8.0 255.255.255.0
Nat Control is not enabled (by default) There is no nat exemption, static identity nat or any nat of any kind set up between the Inside and DMZ.The question is: Will the DMZ network be able to initiate connections to the Inside network or will only outside (internet) access be permitted?
A) No, inside access will not be permitted, only Interenet access will be permitted, because there is no NAT exemption or Static Identity NAT between the lower level security interface (DMZ) and the Higher level security interface (Inside), regardless of the DMZ ACL rule with a destination of ANY.
B) Yes, access to the Internet and the Inside can be initiated because NAT control is disabled and there is an ACL that permits DMZ traffic to 'ANY' destination.
I recently upgraded my asa from 8.2 to 9.1 (reconfigured from scratch - didnot convert old config) and everything seems to be working fine except for communication between my INTERNAL network and my DMZ. Here's my config below -
ASA Version 9.1(1)
!
hostname ZEPPELIN
domain-name MIWEBPORTAL.com
enable password XXXXX
[Code]...
I have setup a few Vpn clients but no ones able to access the inside network.The clients all get a Ip address from the pool and DNS servers Ip's. But cannot ping or connect to there pc's. I'm thining its somewhere in the ACL.
View 2 Replies View Related