I am very new to Cisco ASA and I am trying many days to implement the design below but still cannot get it done. The situation I am facing is
- a host (e.g. 192.168.5.10) under Inside interface can contact to outside without any problem.
- however a host outside (e.g. in VLAN1 or outside this network) cannot contact host under Inside interface. I am using PING test and always get Request Time Out. [code]
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedLet me start by saying that I'm just starting to study for CCNA, so the ASA seems to be a bit above me yet. The ASA's we are using is for VPN to our corporate office and only allowing access to our Citrix environment, so no direct internet allowed. We have a person who works in the remote office who has need for a caption telephone that requires direct access to the internet. The phone only supports DHCP, and getting the ASA to do an ARP reservations is proving difficult. For now I wrote an access list to allow it's DHCP address out but it still isn't working. The access list I wrote is:
access-list 101 extended permit ip host xxx.xxx.xxx.124 any log
access-list 101 extended permit ip any any
access-group 101 out interface outside
When I do a show access-list I'm seeing that traffic is hitting the access list as the hit counter has increased. When I do a show conn I'm seeing one of the IP's that the phone should have access to, however the flags are: saA, so I'm assuming they are not getting a response. According to the manufacturer, only outbound connections are needed, no incoming ports required. All traffic is TCP.
The ASA5505 I am working with has this from the show version:
Licensed features for this platform:Maximum Physical Interfaces : 8VLANs : 3, DMZ Restricted Inside Hosts : 10Failover : Disabled VPN -DES : EnabledVPN-3DES-AES : Enabled VPN Peers : 10WebVPN Peers : 2Dual ISPs : Disabled VLAN Trunk Ports : 0
This platform has a Base license.
Does the Insides Hosts :10 line mean that only 10 devices can be connected to the firewall at one time? I would like to connect an AP to one of the PoE ports and have possibly more than 10 connected. Is this possible with this ASA5505?
I just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
I have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
I'm trying to make a very plain and simple network with the ASA 5505, I've strated from scratch over a dozen times triyng to find where I'm going wrong. My main goal is to simply create an IPSec VPN connection to my ASA 5505 and simply ping and connect to devices with the "inside network", so far I can easily create and establish a IPSec VPN Connection, but up to this point, I cannot successfully ping or access a single device on the ASA 5505 inside network.I've taken, create the IPSec profile with the ASDM wizard, add exemption for the VPN IP Pool, add access-list from this Cisco link, url...All this and I can't make a single connection to the inside network. [code]
View 7 Replies View RelatedI have ASA5505 configured with internal network as 192.168.15.0 and default gateway 192.168.15.1 From the inside network, i'm able to access internet and able to ping all website (enabled ping). and all internel network devices can ping each other. Except i cannot ping my gateway (ASA5505) 192.168.15.1. I'm continously seeing this message on the log, when i tried to ping.. How to fix this?
Denied ICMP type=8, code=0 from 192.168.15.xxx on interface inside
replace xxx with my network devices that try to ping the gateway..I dont want outsiders ping my gateway, i need ping for inside internal network only.
I want to upgrade "inside hosts" from 10 to unlimited on a ASA5505-BUN-K9, Do I have to buy Security Plus license ( L-ASA5505-SEC-PL =) ) before activating ASA5505-SW-10-UL ?
View 3 Replies View RelatedUsing an ASA5505, have 1 static outside address, want to access an inside SBS-Server on SMTP, RDP (3389), HTTPS and port 987
Have configured network object nat rules using the asdm, SMTP works (I can telnet to the server on port 25 from outside), however for some reason I can not telnet inside and out on port 25, so outgoing mail does not work. RDP does not seem to work from outside, 987 I havent tested from outside. When I try to create a network object nat rule for https I get this message from the ASA:
[OK] object network SBS-HTTPS
object network SBS-HTTPS
[ERROR] nat (inside,outside) static interface service tcp https https
NAT unable to reserve ports.
I am using ASA 5505 firewall with base-license. I connected my firewall to one cisco 3750 switch where i created 5 vlans. I done NATing for all vlans and they able to get internet and working fine. They able to browse all internet sites like gmail and yahoo mail.
All internal users are configured to use Outlook for their webmail. Here the problem is with outlook they are unable to send and receive the mails.
If they directly connected their system using public ip( Directly from ISP) they able to send and receive mails from outlook.
I have installed ASA5505 in the network. Port forwarding has been done for one of the server in our LAN. Public users are able to access the server successfully. I am trying to access from inside using the same Public server IP, but unable to access it. Can I have this feature in ASA5505(I think it is loopback configuration). If so, may I know the configuration detail?
View 4 Replies View RelatedI have been working on a configuration for single IP address (on outside ) of ASA5505.I am trying to utilize the outside address 192.168.0.249 to PAT/NAPT to 10 inside machines [code]
What I am not sure of (actually that could be considered all encompassing) is the mapped services/real services.Any constructive comments assistance?
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
I have a customer with an ASA5505 where it will not reply to SNMP polls from any source, i have followed the configuration guide [URL].at and tested another ASA in our internal network and i have that working fine on our LAN, here is the snmp and logging sections of the show-run on the ASA, it there anything obvious im missing to make the SNMP work on this device?
snmp-server host outside 203.XX.75.122 community XXXX
snmp-server host outside 203.XX.84.196 community XXXX
snmp-server host outside 203.XX.86.82 community XXXX
snmp-server host outside 82.XX.244.3 community XXX
[Code] .....
I need to be able to redirect some HTTP traffic to an Ironport WSA (for now) on a DMZ interface, the initial config I'm trying to test is along the lines of the following (don't have access to the ASA at the moment to cut-and-paste):
access-list 101 deny any any neq www
access-list 101 deny tcp host 10.0.2.2 any
access-list 101 permit tcp any any
route-map proxy-redirect permit 101
match ip address 101
set ip next-hop 10.0.2.2
Unfortunately the ASA does not take the "set ip next-hop" command, I get an invalid input error message and if I at the route map config prompt type "?" only the "metric" and "metric-type" commands are listed as available.
This happens both on 8.2 (ASA5510) and 8.4(2) (ASA5505). Since others are able to make this work, I assume there's something else on the ASA that I have to set to enable this command?
I have a problem with mi telephony server. My network topology is very simple. I have an ASA5505 connected to Internet throught an ISP. Behind ASA5505 I have a ToIP Server that operate well inside LAN network. However, when I try to register two or more extensions (Softphones) from Internet, Softphones some times it registers sucessfully, but some times doesn´t work.
The other hand, when softphones outside from LAN get register sucessfully in Asterisk server, is not possible that one of this calling the other one, and Asterisk server detects them as "UNREACHABLE". I don´t know if the problem are all commands of traffic inspect or if the problem is referenced to a particular UC proxy License.
These are configuration lines:
object-group service elastix-ports
service-object udp eq sip
service-object udp gt 10000
[Code]......
I currently have an out of the box ASA5505 and need to change the internal interfact from 192.168.1.1 to 10.20.3.1 so it fits in with the rest of the network.Tried using the ASDM Startup wizard (via 192.168.1.1) and it just seems to hang on "delivering the commands to the device".
View 16 Replies View Relatedi have cisco asa 5505 Security adaptive firewall. my inside network is 192.168.1.0 255.255.255.0 . i want to add static route another network i have that network id is 192.168.2.0 . 255.255.255.0.how i can add the route.
View 9 Replies View RelatedI have an ASA 5505 with 3 host license.I want to configure 2 outside interfaces and have inside interface. The outside interface going to a separate ISP.Will this work or do I need more licences?
View 3 Replies View RelatedHave a problem in config of my ASA5505 --> I can't access Internet from my new created vlan number 4 (Vlan4):
here my config:
ASA Version 8.4(1)
!
hostname FWWIB1
enable password OEIOH8Zv/vNvif8C encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
I have the following config below on my ASA5505, where I want to be able to access remote computers who are VPN'd into the inside network, for support purposes.I want to be able to ping the VPN ip from the LAN, and be able to connect to these computers via the VPN ip. [code]
View 4 Replies View RelatedI have an issue accessing the inside network of my church from VPN. This only happens when I connect from my home network. I have no problem accessing inside network of my church if I'm connected from else where (my Clear Hotspot or someone else's house). Here is the hardware detail:
At the church, we are using Cisco ASA 5510 and we have so many VPN tunnels to different churches. At home, I 'm using Cisco ASA 5505. See that attached configuration for my home ASA5505.
The ASA device is going to be the gateway for multiple distinct inside IP subnets. We can have have a unique outside IP address to correspond to each inside IP subnet if needed, but we need some means for a VPN client or a site-to-site VPN to have acess to a pre-definied IP subnet (i.e. if customer A establishes a VPN connection, they have connectivity to IP subnet X; customer B establishes a VPN connection, they have connectivity to IP subnet Y, etc.).Currently, the two inside IP subnets are 10.10.0.0/16 and 10.20.0.0/16. We will be adding more.The problem we are facing is that we cannot reach the VLAN 201 from the ASA we believe this is because. I have setup two addresses on port 0/1 Vlan1, 10.10.20.2 and 10.20.20.1 as an alias. How can we make traffic for the 10.10.0.0/16 subnet untagged and traffic for the 10.20.0.0/16 subnet tagged for VLAN 201.
View 1 Replies View RelatedI have a brand new ASA 5505 running version 8.2(5). Got connected with the ASDM and ran the setup wizard and the remote access VPN wizard. I am not able to ping the outside interface from the internet, and my VPN client gets no response when trying to connect.
View 5 Replies View Relatedmy environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12
name NextVLAN
state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
i tried to configured L2TP connection on ASA5505.Phase 1 and Phase 2 are completed but Windows Client doesn't work. [code]
View 4 Replies View RelatedI am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies View RelatedI am trying to configure our ASA 5505 so that our users can access our ftp site using [URL] while inside the firewall. Our ftp site is setup so that you can reach it by either browsing to the above url or by browsing to ftp://99.23.119.78 but we are unable to access our ftp site from either route while inside the firewall. We can access our ftp site using the internal ip address of 192.168.1.3.
Here is our current confguration:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif ATTsecurity-level 0pppoe client vpdn group ATTip address pppoe setroute !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveobject-group service DM_INLINE_TCP_1 tcpport-object eq ftpport-object eq ftp-dataport-object eq wwwaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in extended permit tcp any interface ATT eq ftp access-list ATT_access_in extended permit tcp any interface ATT eq ftp-data access-list ATT_access_in extended permit tcp any interface ATT eq www access-list 100 extended permit tcp any interface ATT eq ftp
[code]....
I have two control point, two firewall the second one is linked inside one DMZ from the first firewall route is good and inside the DMZ from first firewall I have servers too.so to be more clear we could call as IP for the DMZ from first firewall, Interface IP 1.1.1.1 that generate this DMZ with first firewall (netmask 255.255.0.0)
inside the DMZ I have an interface from second firewall with IP 1.1.1.5 and inside DMZ 1.1/16 I have servers too keep one test server with IP 1.1.1.3.The LAN passing the second firewall is 2.2.2.1 ever 16 bits of netmask (255.255.0.0) inside the DMZ generated from second firewall I have a machine with IP 2.2.2.9 that need to access in TCP services on machine 1.1.1.3
TCP packets from 2.2.2.9 pass the second firewall and arrive inside DMZ with net 1.1/16 and arrive to server with IP 1.1.1.3 defaul gateway (to answer to originating machine with IP 2.2.2.9) is 1.1.1.1 ASA interface 1.1.1.1 claim a missing related as it haven't mapped the connection that has passed on first firewall. I need only that 1.1.1.1 route packets to second firewall (who own net 2.2/16) avoiding to be trappen in missing related check
at start it was working! around 1 year ago we upgraded IOS to 8.4 and ever so late (one year) doing maintenance to a machine I discovered it was no longer talking with these server on net 1.1/16
I have found on cisco docs chapter 51 and TCP State Bypass before was working, is something that has changed inside ASA IOS 8.4 ?
I have a normal setup of ASA5505 (without security license) connected behind an internet router. From the ASA5505 console I can ping the Internet. However, users behind the Firewall on the internal LAN, cannot ping the Internet even though NATing is configured. The users can ping the Inside interface of the Firewall so there is no internal reachability problem. In addition, I noticed that the NAT inside access list is not having any hit counts at all when users are trying to reach the internet.
When i replace the ASA5505 with a router with NAT overload configuration on it, the setup works normally and users are able to browse the internet.
The ASA5505 configuration is shown below.
hostname Firewall
interface Ethernet0/0
description Connected To Internet Router
switchport access vlan 10
[Code].....
i have asa 5505 with the asdm v5.2 (4), and the asa v7.2(4). This platform has a base license. if i upgrade adsm and asa on v6.2(1) and v8.2(2) if I lose my license and that you need to activate them? i configured site to site vpn (this firewall and the another) that i lose my configuration if i upgrade my firewall.
View 2 Replies View Related