Cisco WAN :: C3750E-24TD-E Connecting Sites Using Multi-layer Switch
Jan 5, 2011
I'm thinking of connecting a branch office to the main office with just using multilayer switch. The sites will be connected using ethernet leased line, so I'm thinking of connecting it directly to the switch.
We're running eigrp on our network so the Multilayer switch will do the eigrp routing.Thinking of using C3750E-24TD-E (IP Services) as the multilayer switch. Can this work or do I still need a router to terminate the WAN?
View 2 Replies
ADVERTISEMENT
Feb 26, 2012
I am looking for an IP Services IOS image for a WS-C3750E-24TD-E switch.Currently have a two switch stack composed of WS-C3750E-24TD-E & WS-C3750G-12S-E.Current IOS running: IP Base.
I need to be able to remove the stub mode for EIGRP, so I am looking for an IP Services image for WS-C3750E-24TD-E switch to be able to run full EIGRP. But I am not able to find one. What is the main difference between WS-C3750G & WS-C3750E switch?Is this even possible for the WS-C3750E?
View 2 Replies
View Related
Oct 2, 2012
i am unable to see WS-C3750E-24TD-SD OID in common services of lms version 4.0.1Is this supported in this version ? and in order to get the support of this device
View 1 Replies
View Related
Apr 13, 2011
I have 3560e which doesn't appear to be passing igmp traffic to the upstream router
PC1 ----------- ASA ------------ PC2--------- 3560e ----------- 3825 -------------------- WAN --------------------- Router ------------- Server
My ASA runs SMR, has an igmp forward interface outside command on the inside and has a trunk port to the 3560e (V lans 32 & 48).PC2 is a test pc on the 3560e on vlan32. 3825 is my ISPs router on vlan32.
- if i try to access the stream from PC2 it works.
- if i try to access the stream from PC1, i see the igmp join leave my ASA onto the 3560E (i've captured on the 3560e's link to the ASA).
I've also captured on the ASA and i can see the igmp packet leave the outside interface but the join doesn't reach the 3825 (i've captured on the 3560e port facing the router and there is no join being forwarded).the switch is running in layer 2, 12.2(35r)SE1.
switch#sh ip igmp snooping querierVlan IP Address IGMP Version Port---------Switch#
Global IGMP Snooping configuration:------------------------IGMP snooping : EnabledIGMPv3 snooping (minimal) : Enabled Report suppression : Enabled TCN solicit query : Disabled TCN flood query count : 2Robustness variable : 2Last member query count : 2Last member query interval : 1000
View 2 Replies
View Related
Mar 10, 2011
Here is a second paragraph from official BCMSN book page 93:
View 6 Replies
View Related
Nov 23, 2011
I'm trying to figure out if the multi-layer Route-Reflector topology would work for me. Let say we have 2 Route-reflectors RC-RR1 and RC-R2 and all other router are their reflect-clients. Now I'm getting a new router RC-.E001 and would like to set new level of Route-reflectors. I'd like that now the router RC-E001 is a route-reflector client of RC-E002 (new level of RR) and RC-RR1, e.g. it will be a client of route-reflectors from different levels.
View 3 Replies
View Related
Apr 22, 2012
Can we stack a 3750G-12S-S switch with a 3750-E-24TD-S switch?
View 4 Replies
View Related
Nov 30, 2010
Does GLC-GE-100FX is supported on the WS-C2960S-24TD-L. I don't see this switch listed under the compatibiilty matrix.URL,But the datasheet for the 2960S says this:"The Cisco Catalyst 2960-S with SFP+ does not support the GLC-FE-100BX, GLC-FE-100FX, or GLC-FE-100LX."But it provides no reference for the GLC-GE-100FX,The easy answer is, no the 2960S-24TD doesn't support it.
View 1 Replies
View Related
Oct 31, 2012
I was wondering if I can stack WS-C3750E-48TD with WS-C3750G-12S together to created a single logical switch.
View 3 Replies
View Related
Mar 9, 2012
Recently on two switches, both being same cisco WS-C3750E-24PD, running with same IOS c3750e-universalk9-mz.122-58.SE2.bin got noticed that the license state of one switch is showing incorrectly as shown below [code] I will not be able to execute any changes/modifications on switch as of now.
View 9 Replies
View Related
May 21, 2013
Has anyone configured Layer 3 port channel on Cisco 6509 switches which are connected over dark fiber between two buildings?
View 3 Replies
View Related
Jul 2, 2012
I have :
- two different subnets (S1, S2)
- these subnets are connected to an IP backbone via wirelles acces points
I would like to physically connect these subnets together so the networks devices in S1 could directly communicate with the devices in S2 and vice versa without going through the backbone.
The obvious solution seems to interconnect these subnets with a router or a switch L3. But I would like to connect these subnets and stay at layer 2.
So, is it possible to connect S1 and S2 with a switch L2 ? If I do that, what is going to happen? Can I create just one subnet S3 from this two subnets when I connect them together and have my two separate subnets back as soon as I disconnect them?
View 1 Replies
View Related
Jul 14, 2011
I have a Windows7 laptop that was working fine til yesterday.I switched it on at home last night and it picked up my wireless connection but when I opened IE or Firefox it would not access any webpage (blank screen, no address that its resolving on status bar at the bottom and just a progress bar (IE) or a 'searching' icon (firefox)The network connection page in control panel says that it is connected and I can ping sites from the command prompt and some other software such as skype seems to be connecting.I have disable both bullguard firewall and made sure the windows firewall is off.I have come into work this morning and am getting the same problems, even when connected by ethernet cable, I can also see other computers on the network.I was occasionally getting a dial up connection pop up box appearing from an old dial-up connection I had set up, but have now deleted this connection.
View 2 Replies
View Related
Jul 14, 2011
I have a Windows7 laptop that was working fine til yesterday. I switched it on at home last night and it picked up my wireless connection but when I opened IE or Firefox it would not access any webpage (blank screen, no address that its resolving on status bar at the bottom and just a progress bar (IE) or a 'searching' icon (firefox) The network connection page in control panel says that it is connected and I can ping sites from the command prompt and some other software such as skype seems to be connecting. I have disable both bullguard firewall and made sure the windows firewall is off.
I have come into work this morning and am getting the same problems, even when connected by ethernet cable, I can also see other computers on the network.
I was occasionally getting a dial up connection pop up box appearing from an old dial-up connection I had set up, but have now deleted this connection.
View 1 Replies
View Related
Sep 30, 2011
Connecting ASA 5520 to two Catalyst 3560G layer 3 switches. What's the best practice to connect the asa-5520 at the edge, to the core of my network? What I'm looking to do is connect two routed gigabit ports (gi0/2 and gi03) to two seperate layer 3 routed ports on catalyst 3560G. I'm wondering how to do it, or if there's any type of failover method? I'm running EIGRP in the network and the link to the first core switch has a /30 point to point connection. Everything works fine, I'm just not sure how to connect the second switch to the firewall. Should I use the a different /30 for the point to point connection to csw02 gi0/48? (See attachment) How would this affect traffic flowing through this interface? Would I have to duplicate rules I have on my inside (gi0/2) interface? Is there a way to make the inside2 interface standby some how? I want to know the best way to set this up, so in the event csw01 goes down I don't loose internet. Will EIGRP work it's magic and only use 1 path to the ASA? Should I even be using routed interfaces on the ASA and just use trunked mode?Running ASA 8.4?
View 1 Replies
View Related
Apr 30, 2012
I need a ≥ 8 port layer 3 managed switch. What would be the cheapest solution for this?I've been looking at some stuff like Cisco 4908G, but that only supports 1000base-X. I need something that supports the standard 1000base-T. I've also looked at a Cisco WS-C3508G-XL-EN, but correct me if I'm wrong, this is only layer 2?
View 11 Replies
View Related
Apr 22, 2011
can i use normal two L3 Switch(3560) for BGP Multihoming with 2 different isp
View 4 Replies
View Related
Sep 26, 2012
I came across this Multichassis EtherChannel Features when read about information from Cisco Smart Business Architecture.After checking further, knowing that Cataly stwitch 6500 supports this feature.provide information that beside Catalyst 6500, is there any other model of Catalyst switch can support this feature?
View 4 Replies
View Related
Jan 23, 2012
We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
View 9 Replies
View Related
Apr 8, 2011
for example, there are 3 sites, A, B and C. A and B are 1.5 km apart and both are separate LAN(mixture of wireless and wired). C is 35 km apart from A and B. I have to connect A, B and C so that they can communicate with each other. Security is required.
View 8 Replies
View Related
Mar 6, 2012
I'm looking to get a layer 3 managed switch. The HP we currently have only does layer 2.I'm looking at a HP v1910-24g. It has 24 10/100/1000 ports and looks to be layer 3 as well.It looks like they can be had for around $350.Anything different I should be looking at with similar specs? Any issues with the v1910-24g?
View 19 Replies
View Related
Aug 24, 2011
I got one SF 300-48 layer 3 switch I tried to configure to use it in the office network.Unfortunately I'm unable to configure the VLAN settings.I need port one for input(VLAN2),port 7-15 for another vlan(vlan3) also need to connect with the vlan 4.port 15 is another vlan(vlan4) this is for wireless.Other ports are static.It doesn't get any connections with other vlans.I wish to know how to configure vlans in GUI mode.I tried , But I can't get the Vlan setting correctly.Also,I need to know how to communicate both vlans in GUI mode.
View 8 Replies
View Related
May 23, 2011
I have 1 internet router 2960 and 2 No's ASA firewalls,The issue is Suppose if ASA-1 fails the failover will happen on ASA-2 but The issue is i dont have a layer 2 Switch in between the ASA's and Internet router, i have to manually shift the cable from ASA-1 to ASA-2,what sort of configuration i can do on 2960 router interfaces to support failover from ASA-1 to ASA-2, I have enough interface on 2960 router to occupy ASA-2. These all 3 devices should be in 1 Subnet.
View 11 Replies
View Related
Apr 29, 2013
I created a lab and I have a few issues. One with a layer 3 switch and another with a ASA 5550.
1. Layer 3 switch: I have created multiple Vlans and I am able to route between them. I can ping the switch IP but not the default gateway to the ASA. I did a tracert of the default gateway of the ASA and once I am past the Vlan gateway it fails.
2. On the ASA 5550 I created the Vlans on sub-interfaces but still cannot get to the internet. ASA config is below the switch config.
View 7 Replies
View Related
Aug 18, 2011
I'm looking at implementing a cisco 3550 Layer 3 switch and would like to know if i can forward ports down to all of my different Subnet Servers/Pc's.
For example. See attached image.10.0.3.5 is a mail server. 4.2.2.2 is our public IP.
I would like to forward TCP port 25 down to our Mail servers IP. Any reason this will not work by using the cisco 3550? Currently we have a flat network (1 subnet) and port forwarding works fine.
View 3 Replies
View Related
Apr 13, 2013
I am tryingto add a new VLAN on my C3560E Layer 3 switch for administration purpose.My goal is to make this VLAN for administration only and to let the administrators from 172.17.1.1 connect to any host of the internal network 172.16.0.0 plus exit to the internet via the default gateway 172.16.1.245.
Here an extract of what done so far:
ip routing
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
!
interface GigabitEthernet0/1
[Code]...
What happened is that:
1. The host connected to Vlan30 can correctly ping the interface it is connected to.
2, The internal network can access the internet
3. The host connected to VLAN30 cannot access the internet and cannot connect to any internal server.
Do I have to add a static route? This is a production envuironment and it is my first experiment with a layer3 switching in production, so I cannot mistake
View 19 Replies
View Related
May 6, 2010
I am experiencing a problem on a Catalyst 4510 (cat4500-ipbasek9-mz.122-53.SG.bin) with 802.1x configured. Client PCs are connected via a mini desktop switch to a Cat 4510 switched port in multi-auth mode. The configuration of the port follows:
!interface GigabitEthernet2/34 switchport mode access ip arp inspection limit rate 30 authentication host-mode multi-auth authentication port-control auto authentication periodic authentication timer reauthenticate server dot1x pae authenticator dot1x timeout tx-period 5 dot1x max-reauth-req 6 spanning-tree portfast ip verify source vlan dhcp-snoopingend
It happens from time to time that the Cat 4510 port stops passing traffic. Reconnecting the mini switch recovers the communication. Client PCs connected to the mini switch seem to be authorized at the moment when the problem occures. The RADIUS Termination-Action attribute is set to RADIUS-Request. The problem is not present if "authentication periodic" is disabled.
View 1 Replies
View Related
Sep 25, 2012
I would like to ask if it is possibe to stack a 3Com 3cr17161-91 to a layer 3 Cisco Switch? The two will be stacked using the avaialble SFP modules.
View 4 Replies
View Related
Feb 9, 2012
I can understand it 's one of those very basic questions , but how do I identify a Switch is Layer 2 or Layer 3 ?Looking through # show version command and checking the IOS version to be IP BASE or LAN BASE . Is it the right way ?Cisco 2960 is a Layer 2 or a Layer 3 Switch ? I noticed that access-lists could be configured which means that it 's a Layer 3 Switch , right?
[code]....
View 5 Replies
View Related
Jan 13, 2013
I've created a scenario using a 3750 cisco as core switch ad other 6 switch model 2900 in access level.my problem is this, the router is not a cisco router, and this router is not able to make NAT on more than one subnet.Into the core switch I've created 4 VLAN and I must to give internet access to 3 of them, 192.168.0.0/24 (vlan1), 172.16.0.0/24 (vlan2), 172.17.0.0/24 (vlan3).I've connected the switch to router via gigabit ethernet 0/1 and I've assigned to this interface ip address 192.168.10.2, the router ip address is 192.168.10.1, Switch ip default-gateway is router ip address 192.168.10.1, ip default route is 0.0.0.0 0.0.0.0 192.168.10.1 I've enabled ip routing feature and I've set no switchport feature to interface gigabit ethernet 0/1.From core switch I can ping router ip address but I can't make it from all other user, and the users not able to have internet access.
Below the switch configuration (only necessary strings)
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code].....
View 6 Replies
View Related
Sep 5, 2012
My understanding is that even layer 2 switches like the Cisco 3500XL can have 1 IP address for management. However, I cannot seem to figure out how to configure it to get it working in a router on a stick setup. I can manage the router through SSH, but I cannot SSH to the switch.
View 3 Replies
View Related
May 25, 2012
I have made a topology by using one 3560 switch and 2 2950 switches. I have also made 2 vlans name Clients and other Servers and vlan 1 is for anagement purposes. The left 2950 switch is for clients and the right is for servers. Clients is vlan 2 and servers is vlan3 . Now what i want is that my dhcp is should assign ips to clients in vlans 2 provided that servers are in vlan 3. I am also using a border router and i have introduced a default route on the 3560 to the border router.
Now when i assign static ips to my clients pc and server dhcp then i can ping between vlans but when i try to assign ip through dhcp then it wont work. Also the default route on the switch to the border router doesnt seem to work. I can ping only the border router when i put a default route on the border router instead of the 3560 switch.
View 3 Replies
View Related
Oct 16, 2012
is it possible to run a Catalyst 4500 as pure Layer 2 Switch, i.e. disabling "ip routing", but still managing the switch via Fa1, i.e. the defautl mgmtVrf vrf ?I tried the following:
!
no ip routing
!
interface FastEthernet1
ip vrf forwarding mgmtVrf
ip address 192.168.1.1 255.255.255.0
!
ip route vrf mgmtVrf 0.0.0.0 0.0.0.0 192.168.1.254
ip default-gateway 192.168.1.254
I was not able to reach the Switch even from the same subnet. Only after enabling ip routing I could manage the Switch. I haven't found any command to set ip default-gateway for a vrf. Any workaround to keep routing disabled, but still manageable via VRF?
View 3 Replies
View Related
