How to configure T3/E3 Interface on Cisco 3825. It got 2 Co Ax Ports (1 for Tx, 1 for Rx). I enabled the port using below command. card type t3 2
Later I configured below commands
interface s2/0
description dfgsg
ip address 10.123.23.2 255.255.255.252
[Code]....
I have a Cisco 3745 Router with 1 Subrate T3/E3 port card installed on it. We want to add another T3/E3 card,
Q1- Can i add another card in this model? Q2- Can we multilink bundle up two T3/E3 cards? (current we have a single DS3 P2P connection between two office, so want to increase the bandwidth)
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
I want to configure PAT on the router I have no configuration yet
View 1 Replies View RelatedI want to build up cisco 3800 series router as terminal server , i have Asycs 32A module in cisco 3825. Here is show version of device.Do i need to installed any specific IOS in Cisco 3825 device ? how to configure cisco 3825 as terminal server.
View 1 Replies View RelatedI thought I saw a post/question in regards to "how to" configure a Broadband backup for a MPLS circuit.. What I am trying to do is use a cable/dsl/ broadband (secondary) connection as a backup to a MPLS circuit (primary). I have EIGRP and BGP configured on both the branch endpoint and the tunnel headend. The tunnel is used by the interface that connects to the secondary circuit. The branch location router is a 1841 and the "headend" tunnel router is a 3825. I am wondering about the configuration/syntax of a "weight" or static route that can be used to have data flow over the tunnel when the MPLS circuit goes down - and then switch back to the MPLS circuit when it comes back on line.
View 1 Replies View RelatedThis is my Cisco LAB environment used for study but also in production for daily use. I am trying to setup a double-NAT network with just one IP from my ISP through the ASA & 3825 going to (2) end nodes and multiple ports for port forwarding. It is currently working but only as simple PAT and I cannot initiate FTP from the outside. removing the router, but this is my study LAB and it's a bit unconventional for learning purposes. I attached the diagram and need parts of the config.
View 14 Replies View RelatedWe have one 3825 router used as voice gateway. For redudancy, we want to connect it to two different switches which has STP and HSRP running. Can I create a port-channel with two Giga interfaces in 3825 and connect to two different switches? Should I configure port channel in switch with only one port in each port-channel? I know server can be connected to different switches with NIC teaming. I just want to mimic that kind of setup. I did one time for port-channel in 3825, but it was connected to a stacked 3750X. So it's different case now.
View 2 Replies View RelatedI have a Cisco 857 router which i used for Internet connection with RJ11 connectior (ADSL0 POTS) but now the ISP has changed the internet link with PPOE type and the ONT connection is RJ45 , Is there a possibility to configure one os the Fast Ethernet ports as WAN port for internet.
View 2 Replies View RelatedWhat is network port ? I want to configure a trunk port as network port, so that the trunk port becomes the network port for all the VLAN associated to the port.
View 18 Replies View RelatedI currently have a Cisco 891 running with a FTP running on port 21. I currently have the NAT from external IP to and internal IP 192.168.12.6 for port 21. And the firewall allowing that traffic through and client software is working fine. However I need this FTP to be running on port 990 and anytime I change the NAT and the firewall, the external FTP clients connect but then drop when recieving the directory listing.
View 18 Replies View RelatedTo configure DSL port forwarding,I want to configure as remote desktop.
View 3 Replies View Relatedhow do i configure a laptop internet port. cos anytime i plug a cable to browse i dont get internet service?
View 1 Replies View RelatedIs it possible to configure a Cisco 2801 router with Multipoint Port Channeling? A service provider dropped a 4.5Mbps ( 3x T1s ) to one of our customers without any equipment. They assume the CPE responsible. If so, any links to documentation on this configuration. If not, what device will they need to buy from Cisco that can bundle these 3 T1s together then feed it into their router?
View 6 Replies View RelatedWhen I try to configure a voice port (like voice-port 0/0/0:15) after doing a conf t, it gives me an error of invalid input detected.We are using a Cisco 3945. We have successfully setup 3825 and 2851 in the past.
View 2 Replies View Relatedwe are using 2960 cisco switch asn we are trying to configure port security.we are able to configure MAC base port security, but unbale to configure IP base port security.can any one guide us can do IP base port security like MAC port security. if not which switch will support IP and Mac base port security.
View 6 Replies View RelatedI have CSS in single arm deployment model. I want to configure port redirection for the servers. Servers are actually running web service on port TCP 3636. Which is accessibale by VIP http://192.168.200.87:3636 but I dont want to give user this URL I want the user to use standard HTTP URL as mention below, I want user to open http://192.168.200.87 and once they access this URL automatically CSS redirect them to port 3636. How I can achive this. I am using IP addresses for the load balancing.
View 4 Replies View RelatedI need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit . Any step by step command.
View 9 Replies View RelatedI have ASA 5505 with 8.4(2)8 software for one of my branch offices and I can't configure port forwarding.It seems to be very simple, but it's not working. I use my ASA as a gateway to the internet for users in office and for site-to-site IPSec VPN to HQ. I have pppoe-enabled outside interface, but ISP gives me static routable ip address. I have server behind my firewall and I should "publish" to the WAN some of its' tcp and udp ports, but I see that no packets forwarded through ASA. I tried to configure PAT as stated in official "Cisco Security Appliance Configuration Guide" through CLI and ASDM.[code]
View 4 Replies View Relatedhow can I configure QoS in the router CISCO1841 for the port IPSEC(UDP 500 ,UDP 4500) and the port tcp 4433
View 5 Replies View RelatedHow do you configure port-security on a 2811 router? If not, is there a way to configure some type of security on each port ?
View 3 Replies View RelatedI have a Cisco SG300-20. I have read the documentation and cannot seem to locate the instructions for port forwarding. I need to forward TCP port 8088 to IP address 192.168.14.110 on the switch.
View 5 Replies View Relatedi have a cisco asa 5510 and would like to add a NAT rule for a range of ports like 50000-59999
View 15 Replies View RelatedIs there a way to send an SNMP trap form the ASA when port 80 is trying to be accessed??
We use the ASA5510 and also use ScanSafe Web Security. Web Security is great but we find ourselves worrying if user has edited their Browser connection settings to remove the proxy settings that we push down using Group Policy. We also cut off the users ability to make changes to those settings but it interferes when I need to troubleshoot a special program that cant use a proxy server. It just makes it harder for me. The other thing is that Group Policy only works for IE. Google Chrome will inherit the system settings in IE. So we have Safari and Firefox as well as a lot of others to worry about not getting the configuration. There is also debate about limitting the use of anything but IE and FireFox.
Without laying down the law and getting all sorts of hate mail and death threats I would like to run ScanSafe in such a way as to make sure each user receives the Group Policy settings and that is all.
I would now like to just set up an SNMP trap on the ASA for ANY traffic that is trying to get to port 80. Either get in in my syslog server or have the asa email me directly. Scansafe sends the Internet traffic out on 8080 to the Proxy towers.
I could block port 80 outbound but again, I limit my ability to troubleshoot on the fly. I would have to break this every time I need to troubleshoot.
In our premises i want to configure cisco 2960G 24 port switch using hyper terminal commands.
View 1 Replies View RelatedI need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit.
View 1 Replies View RelatedI have a cisco L2 SG300-10p Managed switch . I want to configure one port as a turn but cant find the command Encapsulation dot1q . Its a poe switch i want to use for both internet and voip in separate vlans.
View 1 Replies View RelatedWhen trying to configure ERSPAN on a ASR1006, I'm not getting any traffic on the destination port. ERSPAN flavour is LOCAL SPAN, as described in:
[URL]
Configuration used, is the following:
monitor session 1 type erspan-source
no shut
source interface GigabitEthernet0/0/2
destination
erspan-id 10
ip address 10.10.10.1
[code].....
Apparently everything is configured in the proper way, however I’m not getting any traffic in the destination port. Also I’ve noticed the following in the details from ‘Session 1’:
Destination IP Address : 10.10.10.1
how to configure Local SPAN using ERSPAN?
is it possible with LMS 4.0 and VLAN Port Assignment also to configure auxiliary vlans?
1. I selected Configuration > Workflows > VLAN > Configure Port Assignment.
2. Selected my device (a test switch WS-C3560-8PC-S)
3. Clicked List Ports
All ports were listed, port Fa0/1 has only a native vlan, the ports Fa0/2 - 8 have native and voice vlans (auxiliary) configured manually.
So when I want to configure the voice vlan for Fa0/1 the voice vlan is set as the native one.
Is it only possible to configure the native vlans with the VLAN Port Assignment of LMS 4.0 ?
I want to configure my SRW248G4 switch thru console port. Unfortunately in this switch there is no RJ45 console port input, I can only see cosole port that is look like RS232 input. I bought two standard cisco console cables that have one end with db9 and one with RJ45.
Now I have and idea to put one end of one cable (db9) to switch, and one end (db9) of second cable in my computer (COM input/output)
I need to connect two RJ45 together - this is not a problem, I know how to do this. Here is the question :I know how pinout in my computer look like but i can't find pinout of console port in my SRW248G4. There is many pictures in Internet, for many Cisco devices but this isn't working. Maybe in LINKSYS pinout look different ?
I am facing problem in configuration with SF-200-24P Switch . I am failed to configure two vlans on same access port i.e. data vlan and voice vlan. there is an option of auto voice vlan with vlan 1 and i changed to our voice vlan i.e. vlan 101 but didnt work. I tried many options. when i assign single vlan on each
access port it works . I have to configure like to work both data vlan and voice vlan with one access port. I worked on enterprise cisco switches its simple but on small business switch first time i am working.
How to configure this setup.I have an ASA5505 with dual wan failover, FiOS (eth0) & Cable (eth1). how to configure the port forwarding for all my devices so it doesn't matter what external interface the traffic is coming from. For example, I need web traffic on port 80 forwarded to 192.168.1.150 regardless of whether it is coming through eth0 or eth1.
View 2 Replies View Relatedhow to configure the backup port for the management interface for a WLC 2112. I see in the documentation that it states:
"Each interface is mapped to at least one primary port, and some interfaces (management and dynamic) can be mapped to an optional secondary (or backup) port. If the primary port for an interface fails, the interface automatically moves to the backup port. In addition, multiple interfaces can be mapped to a single controller port."
But nowhere can I find where it says how exactly to do it. Google seaches have come up empty as well. I am connecting the WLC to a 3750 stack, and would like to have a secondary port from the WLC connected to the second node of the 3750 stack. So far I have connected port 1 (management) of the WLC to a port on node 1 of the stack which is configured as a trunk and everything is workign fine. I have also connected port 2 from the WLC to a port on node 2 in the stack that is configured the same as the port on node one. how to tell the WLC to use port 2 as the management backup if needed.
[URL]