I have open my 25, 110, 80 port on my Server from local i can telnet all those via my private ip but from public ip its not responding.
2nd thing I can ping both ips of My server through private ip and through public ip.
I have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies View RelatedI configured ASA to open port 21, 3389, 5900 (outside access in) but when i check port just success : 21 and 3389, Error: 5900 If i configured with only one port 5900 or 3389, is't ok, i don't understand what 's the problem?
ASA5510>
ASA5510> ena
Password: ***********************
ASA5510# show run
: Saved
[code]....
I have a Cisco 877 connected to a VSAT modem, and I can't open ports outside, I dont know why?The Cisco 877 Fa0 port is connected to the VSAT modem at VLAN9, and the rerst of ports are connected to the local lan network at Vlan2. I can enter to Internet, but I can't open port outside. ADSL over pots is not used here.I need to open port 81 for ip address 192.168.1.130 and I dont know why this isn't working. Also if I do: sh ip nat translations I see this:
sh ip nat translations
cisco877#sh ip nat translations
Pro Inside global Inside local Outside local Outside global
tcp 172.30.xx.122:81 192.168.1.130:81 --- ---
udp 172.30.xx.122:81 192.168.1.130:81 --- ---
[code].....
How can I allow all ports to be open? I don't really want my 1811 to block any traffic. I tried the command access-list 1 permit any which allows me to surf the internet, but when I check my web server, and port 3389 (Remote desktop) on yougetsignal.com it says those ports are blocked.
View 6 Replies View RelatedI need to open ports 25, 993, 995, 443 and 465 to setup MS-Exchange. I don't have an inhouse IT guy and this seems pretty straight-forward in theory but I can't figure it out I need to open ports 25, 993, 995, 443 and 465 to setup MS-Exchange.
View 5 Replies View RelatedI'm setting up a second exchange 2010 server at a DR location and have been experiencing some problems. The two sites are connected via a pair of ASA5510's using the point to point VPN. I want to rules out any possible VPN issues that may be blocking ports and wanted to see if there is an easy way to do this and simply allow all traffic without any restrictions between the two ASAs. I've attached the scrubbed configs here...Ewing is the primary site and DBSi is the DR site.
View 2 Replies View Relatedwhat command should I use to see all open TCP and UDP ports on my router?
View 2 Replies View RelatedI was told i need to open certain ports to certain IP's,what ports need to be opened to what IP's for the folowing game as im close to giving up.The games are as follows - Call of Duty 4, Counter Strike 1.6 and Source, Warcraft III, and StarCraft 2
View 2 Replies View RelatedThe problem is I don't know what to do to open my modem's ports because every single of them except of 80 is blocked,im having some latency problems on online games etc, I asked my ISP and they didnt probably understand what the port is they offered me changing my IP to PUBLIC IP for onetime payment, seeing as they probably dont know what the port is im confused now, will the public ip unblock the other ports?
View 19 Replies View RelatedNo ports seem to open up when they are supposed to be open according to the routers GUI.When i use "port checker"-websites, they even say that port 80 is closed until i actively open it in the router, then it shows up as open. This however only applies to port 80, no other ports shows as open OR allow any traffic through.The same thing happens when the router is in DMZ.What I have done so far is google my butt off without any results, I have tried a new router, a new network card, formated, re-installed windows and made sure that my ISP is not blocking the ports that i have tried to open.My purpose of opening a port is to run a mumble server, which I have run on a Hamachi VPN so far, and that has worked fine.
View 10 Replies View RelatedI can't open up any ports.I've tried using applications such as Simple Port Forwarding, PFPortChecker and manually by opening my router gateway (192.168.1.1).I can open a port, but if I check whether the port is open, it says that the port is closed. I tried opening ports through Windows Firewall and even disabling firewall, still won't work.
View 14 Replies View RelatedMy reports say that my listen ports are blocked even though I removed my router already. I've enabled these ports in Windows firewall already. Why are they still blocked?
View 4 Replies View RelatedI have 3 xbox 360s in the house and im having nat trouble with them, i am currently using an actiontec pk5000, from centrylink. i need to know if there is a way to open all ports on this router or if i should get a router/switch that i can open the ports on and use dmz on the actiontec for the new router to make this work.
View 2 Replies View RelatedI am thinking about opening a port for a certain multi-player game. I was just hoping to know if opening a port for this game could leave me vulnerable to hacking or other stuff like that.
View 4 Replies View RelatedI have this problem i can't open my ports on my D-link 524, i have opened about 6 ports so that my XBOX 360 works with a open nat, i have also set the DMZ to my xbox's IP which is static btw, my PC is also static. This is how i basically tested and it told me that it was not opened. I went into:
192.168.0.1 -> Advanced -> Virtual Servers ->
Enabled
Name: XBL1
Private IP: 192.168.0.100 ( because i was testing it on the computer - if it
were 360 it would be .141 )
Both UDP and TCP at port 3074
Schedule=Always
Apply -> Then restarts modem/router i waited for 2 minutes before turning them on again, i turned router on first because some guide told me to do that.
I did exactly what they did on portforwarding.com then i opened up portchecker and typed in 3074 and pressed check -> This port is NOT opened. What is wrong? This is how my net is set up.
Modem ZyXEL -> D-Link 524 -> D-Link DGS 1005D -> Computer/XBOX.
I am pretty new to Cisco - and I have a little 506E that I love. I got it working with my first scenario where I have one server that is my web, and e-mail server.I also opened the RDP port so I can remote into it. The IP's for the old server are internal 192.168.1.23 name ferbweb-external 71.12.111.219 name ferbwebpub. Now - I need to add another server in the exact same way with the same ports 80, 25, and 3389 open to the outside - IP's internal 192.168.1.31 name ferbmail and external 71.12.111.220 name ferbmailpub.I can get to all of these ports on the new server on the inside network - so that is not the problem.So, I went into the config, copied the statements for the old server, and changed them for the new server and added them to the config. I can still get to the old server from the outside fine, but cannot get to any ports on the the new server from the outside at all.I have done a lot of research, and cannot find what I am doing wrong.
View 6 Replies View RelatedI need to open ports 5000 and 5001 on my Cisco PIX 501 to enable some users to be able to connect to our CCTV from outside, how should I open these 2 ports?
View 1 Replies View RelatedI just finished implementing a VOIP install and I am trying to setup some softphones and in order to allow the softphones to work I need to open some specific ports for outbound. I am not a Cisco guy, I am a Windows Administrator that also has to maintain my Cisco infrastructure.
View 3 Replies View RelatedI'm using a WRVS4400N and have all the proper ports open as well as the corresponding ones in the windows firewall. I've tested this with multiple port checkers online, such as grc.com. I've even go so far as to put one computer on a dmz and turn off the firewall on others. I've tested multiple ports on different computers. As well as from different remote gateways (other people's computers) just to see if it was a loopback problem.
I have the latest firmware installed and have done this from a clean install as well. This problem won't go away. My addy is nbcr [dot] dyndns.info if you'd like to have a test yourself and see that 118 is indeed closed.
I have an extensive computer repair background and run my own shop repairing computers, however networking is my weak area. Oh and its version 2.
I have an ASA 5505 with ASA version 7.2(2) and ASDM version 5.2(2) and I am attempting to open ports 88 and 5445 and forward them to the IP address of my DVR. This is all new for me. I see several posts for other software version to do this same thing but my version appears to be older?
View 1 Replies View RelatedHow do FPS's open UDP ports without needing to configure the router to forward them?I never have to forward ports from my router to my PC. Every game i have somehow manages to open the UDP ports it needs without me having to configure my router. Yet when i check to see if those ports are open (prior to starting the programs) they always come back as blocked or closed. Now I'm currently working on a UDP Internet program and need to know how to do the same thing - open ports on a router without having to make the customer configure their routers. I'm THINKING that other programs start with a TCP/IP connection on the desired port and that opens the UDP port. Is this the answer or is there another method used?
View 5 Replies View Relatedby saying "open ports" in a router or PC or other Network System what we mean basically? what is opposite terminology, "closed ports"?-used or unused-sensitive-vulnerable or non vulnerable to attacks-exploited easily and when so may attacked and have much bad/serious consequences/results
View 2 Replies View RelatedBeen trying for hours to open the ports on a motorola 2210-02-1022. I have a linksys wireless router. I think the default IP is 192.168.0.1 I put this in browser and get a user name and password window. What do I do from there. I have the port numbers from xbox.
View 2 Replies View Relatedto access VOD database i must open three ports on the router - not sure how to
View 3 Replies View Relatedwhy I cannot get any of the standard ports open on my computer. I have run ESET firewall/antivirus, but have it temporarily disabled. I have windows defender disabled. I have the correct ports open/bypassed through my linksys router, but still am having network trouble.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Enterprise , 64 bit
Processor: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz, Intel64 Family 6 Model 26 Stepping 5
Processor Count: 8
RAM: 6135 Mb
Graphics Card: ATI Radeon HD 4800 Series , 1024 Mb
Hard Drives: C: Total - 953866 MB, Free - 610614 MB;
Motherboard: ASUSTeK Computer INC., P6T DELUXE V2, Rev 1.xx, MS1C96B19100148
Antivirus: ESET Smart Security 4.2, Disabled
My company deals in a video conference software which requires certain ports to be open to work correctly, including tcp and udp ports. Clients who want to test / purchase have different kind of network setup. I usually tell them to open those ports require by the software on their end. How do i ensure if the port range required by my software is open once I am at their location. I have installed a few network scan tools but not sure what ip do i scan. Should I scan my server's ip once I am at their location and connected ? or should I scan their gateway ?
View 5 Replies View RelatedI have been trying to host games for some time now with no luck. I believe it is because i cannot open the proper ports. I own a Linksys BFSR41 Ver. 4 router. I have been trying to open ports, testing them on a port checker website and they are always listed as closed. I have followed the guide on portforward.com perfectly with no luck.I have disabled Block Anonymous Internet Requests.I have disabled my Windows firewall, and AVS. Still cannot open ports.I have also updated to the latest firmware. I am using Win-7 x64.
View 1 Replies View RelatedHow to open ports 443 , 11002,11001 on xp
View 2 Replies View RelatedHow do I open all the ports for ALL of the ips on my dedicated server. I opened all the ports for the main ip that I RDP (Terminal Connection) into, but I can't seem to open the ports for the other ips that I got from my dedicated server provider.
View 1 Replies View RelatedI am trying to Open some ports on a Linksys E1000. When I run the Shield Up test to see the status of my ports the ones I want to open are closed which is normal but when i try to portforward any port the status goes from closed to stealth. That really does not make any sense to me why when trying to open a port it becomes even more secure then if I did not try to open it. I turned off the firewall and the only thing I see might be the wireless security on the router. I have no idea what that means tho so idk if it is even a firewall.
View 1 Replies View RelatedI am considered as a novice when it comes to networking, modems/routers etc.I have a Belkin Modem/Router, I need ports TCP 80, 2300 and UDP 2310 I think to be forwarded so I can play a certain game online (Age of Empires 3). I have tried DMZ mode for my pc and I can play the game online but only with DMZ enabled. Just some extra info.Belkin Modem/Router model : F5D7634-4A-H v2 (on the device)F5D7634-4-H v2 (01) (on the online settings (192.168.2.1))It has the latest firmware as I have clicked on the firmware update and it says "There is no new firmware update available for this Router!"
View 11 Replies View RelatedA year or so ago, when Verizon was my ISP, I ran a Minecraft server with a Hamachi VPN. I had looked into forwarding ports at the time, but decided to go the VPN route because I wasn't completely sure how to assign a static IP to a computer on the network. I had absolutely no issues setting up the VPN or hosting a server on the network.Recently I decided to give port forwarding a go again. I successfully assigned the static IP and put the port number into my router's port forwarding settings, but the port was still closed. I tried using online port checker tools and having friends try to log into the Minecraft server. No luck.After reading multiple port forwarding tutorials to make sure I had everything correct and double- and triple-checking all my settings, I began to suspect that something else was causing the problem. I have an older router set up as a repeater on the network so my family can connect to the Wifi network from anywhere in our house. Thinking maybe the repeater or even the main router itself was to blame, I decided to try another router. After disconnecting the current routers and setting up a spare router I had, I tried everything again. Still no luck.
I tried opening different ports unsuccessfully. No port I tried opening would work. I decided to give in and just set up Hamachi again, since that had worked flawlessly before. However, after setting up a Hamachi VPN, I realized people could join the "room," so to speak, but could not connect to the VPN itself. Even hosting a Minecraft server over Hamachi wasn't working this time.Assuming it was just an issue with Hamachi, I tried another VPN software. I got the same error - people could log in, but not connect to the VPN. Thinking back to the port checker telling me port 80 was closed, I pretty well gave up.I've walked one friend through setting up a VPN the exact same way I did, and it worked on the first try. I walked another friend through assigning a static IP and forwarding ports. I don't know what's different about my network that won't allow either of these things. I've searched my router's configuration for any setting that would override port forwarding or block a VPN, but I can't find anything.