Cisco WAN :: X.25 Record Boundary Preservation For Data Communications Networks?
May 2, 2011
I am trying to setup RBP to the X.25 connections to be routed to a TCP portI need connect by PAD (dialing) when the device connects it asks for the password of the router and does not open the TCP port.
View 2 Replies
ADVERTISEMENT
Apr 25, 2012
I have a requirement to preserve markings end to end across a network utilising 3750X switches, I am marking the packets without a problem, but due to the rewriting function the marking is being overwritten by ther COS-->DSCP maps.To simplify the scenario I have set up a test environment (see Diagram) and am using ICMP as a simple test using ICMP to test with Both 3750 have 12.2(35)SE5 3750-1
mls qos
mls qos rewrite ip dscp
ip access-list extended ICMP
permit icmp any any
Class-map ICMP
match access-group name ICMP
[code]....
I have used wireshark to verify that the packets are being marked, with the' mls qos rewrite ip dscp' they are, without rewriting does not occur.Moving my sniffer to the 3750-2 I am monitoring the Layer3 connection (marking preserved), however on the layer 2 trunk the marking has been reset to 0 , if I remove the 'mls qos rewrite ip dscp' from 3750-2 then I see the marking on the layer 2 trunk, however I am then unable to remark anything generated on this switch. I believe with the 'mls qos rewrite ip dscp' enabled the L3 to L2 transistion removes the IP DSCP sets the COS to 0 and themnthe COS to DSCP mapping ensures the DSCP is set back to 0.I have tried implementing additional marking policies on 3750-2 but to no avail.What I need is ensuring that that a frame / packet marked in 3750-1 can keep it's marking to the end system over layer 3 and a layer 2 trunk. The only place I wan t the marking to be stripped off is when the dot1q tag is removed as it goes through an access port.
View 1 Replies
View Related
Jan 7, 2013
We an 887m router in our office with an unmanaged switch. We have two networks, 192.168.0.x and 192.168.11.x connected to router on the same interface (192.168.11.253 is a secondary ip) but I can seem to be able to route packets from one network to the other. Internet traffic is fine from both networks. I can't see what I'm doing wrong here. I can ping the 192.168.11.253 (router) from the 192.168.0 network but nothing beyond that.
I tried this at home with no other config and its the same. Is this by design?
View 4 Replies
View Related
Jun 21, 2012
I have two network card in my server and they are connected with different network and we are sharing data between them, but i dont know how, how to transfer data between these two different network.
View 4 Replies
View Related
Mar 7, 2013
They want to make audio recordings of their meetings, and have them end up on the server. I'm trying to figure out how to do this with a minimum of setup and post-processing. I'm also an audio guy, so I understand a lot of the tech issues. I had was to use a USB mic connected to USB to LAN converter to connect it to a computer that was authenticated on the network, and have recording software write the audio file to the server. I'm using a Windows Server 2008 with Domain-based authentication. The network is running through a Cisco Catalyst 2960 switch.
View 1 Replies
View Related
Feb 14, 2011
how to add DNS server for windows 7
View 1 Replies
View Related
Jun 8, 2011
Is there a way to check or record from where the Windows XP pro workstation is getting the wrong IP address and placing it into its DNS cache?
[code]...
View 3 Replies
View Related
Apr 27, 2013
I loaded the following MIB into PRTG 'CISCO-WAN-3G-MIB' hoping to record RSSI and ECIO values on my 3G 1941W cisco router. RSSI is now recording using 'c3g current gsm rssi' however ecio isn't recording using 'c3g current gsm ec io' or 'c3g notif ec io'.[URL]
View 1 Replies
View Related
Feb 8, 2012
Automatically some client ptr record vanishes from dns where as host (a) record exists, how can i verify from client side or how can i see logs files in client machine for the same.
View 1 Replies
View Related
Jan 20, 2011
There is one page of my own website I cannot access from my office (java runtime error). But, when I take my computer home, it accesses the page just fine. Only difference besides IP address on my end is a DSL modem at the office (firewall disabled) vs a cable modem at home. My provider tells me the problem is on my end. Is there any sort of internet communications logging software that will pinpoint exactly what is happening?
View 2 Replies
View Related
Dec 7, 2011
I have a Wi-Fi system in my house but have recently purchased a new laptop. I do not have the original record of the security key
View 1 Replies
View Related
Apr 20, 2011
im using a intel mother board desktop pc and windows xp. i was tray to add external wireless modem .the modem drivers already install successfully but its not working properly it working only 1st 5 to 10 minute.my pci simple communications controller also not installed
View 1 Replies
View Related
Dec 8, 2011
Is it possible to install the D Viewcam software on a PC that is offsite (different network) as the camera and record from there? Basically the camera is home and you record from work.Can I record directly to any NAS (same network as camera) without having a PC in the middle? Or do I need a specific NAS?What about one of those external hard drives that hook up directly to a router?
View 1 Replies
View Related
Nov 25, 2011
If you have problems setting up a computer as a domain controller,what would be the best approach? Four DNS Zones you can configure? What policy would you use to record unsucessful logons to a workstation?
View 4 Replies
View Related
Feb 16, 2011
Basically, my brother uses about a gig a day of our broadband and blames it all on me. I need a way to record my broadband usage (only on my computer, not the network) per day.
View 1 Replies
View Related
May 16, 2012
Any app i can install which will monitor my lan connection for dropouts? i have searched but can't find any that work. I just want a simple app that will note down each time the lan loses connection and keeps a log so i can be sure if its the computer or the network at fault.
View 1 Replies
View Related
Jul 22, 2012
I have a WAN router that's on 172.x.x.x segment, and another WAN router that's on a 147.x.x.x segments.How can I make them communicate, I would like to interconnect both segments to talk to each other.We are using a Cisco 2800 on both segments.
View 8 Replies
View Related
Mar 24, 2013
We own a Wifi controller 5508, with many access points connected to him. Except on the site where the controller is installed, all other APs are configured in FlexConnect mode through our MPLS network to prevent roundtrip for local communications (local client to local server for example).
Because of important slowness on one site where 8 APs are installed, we captured the traffic going in and out of our MPLS router and we discovered that the APs are consuming about 150kbits/s each in one-way communications with the controller (controller to APs), even when nobody is present (the capture was done this sunday).
Could you confirm me if this behaviour is normal or not ? What could explain such a large amount of data between the controller and the APs ?
View 11 Replies
View Related
Aug 28, 2012
I'm trying to get a node in SVI1 on VRF1 to speak to another node in SVI2 on VRF2 to reach each other. After hours of failure, I went to outside resources. Everything I read on the internet says it's not possible on this platform and at least one TAC engineer seems to agree.
I just can't believe such a high-end data center switch is not capable of handling such a basic feature.
View 1 Replies
View Related
Aug 20, 2012
I have an ASA 5510 attached to 2 internal networks. Everything is working except communications between the 2 internal interfaces.I can ping the FW from either interface and I can ping hosts on both networks from the CLI but can't get any traffic to pass.I'd like to open the connection to all traffic. [code]
View 33 Replies
View Related
Nov 8, 2011
I have a couple 3750 switches that I am trying to run VTP Version 3 on.one as primary and the other as "server" which implies secondary from my research. [code]Additionally, running a show VTP devices yields a "No VTP3 devices found" on both devices. Despite ensuring that the domainname and password match.I have a patch cable from Gi1/0/1 on switch one runnning to Gi1/0/1 which from what I read is acceptable on GigE.
View 2 Replies
View Related
Apr 26, 2011
I have an 1811 configured with dhcp scope and generally it works correctly. I have a host on the vlan/subnet that the scope is assigned that can receive an IP and all the specifics from the dhcp server. [code]
The host on the vlan/subnet should use the router as the dns server to resolve static hosts that are configured on the router itself. Can an IOS DHCP/DNS server do this?
View 1 Replies
View Related
Apr 1, 2012
how to download pci simple communi..... for dell laptop
View 1 Replies
View Related
Nov 2, 2005
Just got a D610 with no drivers cd. Rebuilt the laptop with TxDOT image and now I get a message found new hard ware pci simple communications controller. Where can I get this driver at?
View 8 Replies
View Related
Dec 26, 2011
I’m trying to configure my ASA 5505, in order to allow my inbound and outbound mail communications. Here with this mail I’ve attached a diagram which illustrates my exact network setup along with ip addresses.
In this setup I’ve enabled port forwarding on my ADSL router (port 25 and 110) and configured the ASA accordingly, and my mail server is located inside my network.
My problem is currently I can send mails from my inside network to outside but my not receiving any mails which originate from outside. I’ve attached my current ASA configuration as well,
C:UsersSuthakarDocumentsOffice_DocsThakralABC Computers
Final config on ASA5505
host name Cisco
enable password 8Ry2YjIyt7RRXU24 encrypted
password 2KFQnbNIdI.2KYOU encrypted
names
!interface Vlan1
nameif inside
security-level 100
ip address 192.168.155.201 255.255.255.0
[Code] ......
View 3 Replies
View Related
Oct 21, 2012
How to configure ASA not to drop packets with ip option 7 (record route)? According to the docs, ip inspect ip option will drop all ip option packets except 0,1,and 20 (EOOL, NOP, or RTRALT):
"If an IP header contains additional options other than EOOL, NOP, or RTRALT, regardless of whether the ASA is configured to allow these options, the ASA will drop the packet. "
Also, policy-map type inspect ip-options treats only these 3.
View 1 Replies
View Related
Feb 16, 2010
I experinced critical problem for our customer service pertaing to communication fail for FT between FWSMs.
I can just find the log in FWSM as follows and can't find any physical log as interface down in C6500 at that moment.Now our FWSM OS version is 3.2(7) and jsut monitor-interface option is applied at outside interface in FWSM.
[code]...
I already opend the TAC case (SR 613646199) but I didn't get any correct cause for problem and they just recommend to change the FWSM through RMA.
View 10 Replies
View Related
Jul 25, 2011
Does ZoneAlarm's tvDebug log file record the websites I visited? And if so, how do I delete it?
View 3 Replies
View Related
Feb 12, 2011
i can not get the PCI Simple communication Drivers where can I get it for a Dell Latitude D610
View 2 Replies
View Related
Jun 25, 2011
We just moved into a new apartment. In our old place, we had Comcast cable internet with a modem and our wireless router worked fine. Now with Hotwire, we can't get the router to work. Here are the details:
-We can plug our computer directly into the ethernet cable outlet in the wall and it connects.
-We didn't get a modem from Hotwire.
-Wireless router: Linksys WRT54G
We've tried already to change router back to default factory settings. Didn't work. We reset our passwords for the router. Didn't work. Tried to put in the MAC address of the computer and it didn't seem to work. We originally were able to connect a computer to the internet through the router sometimes but just the wireless section didn't work.
View 7 Replies
View Related
Apr 16, 2011
When I view my DCS-932L camera in the Main Console of DViewCam, I can here the sounds in the room being viewed. But if I record the video and play it back, there is no audio on the playback. I have the microphone on the camera enableI now have sound recording, however, the audio is about 3 seconds behind the video. Is there a setting somewhere to keep them synchronized? I have checked all the video sync checkboxes I can find.
View 4 Replies
View Related
Dec 9, 2005
I'm searching for a driver for the PCI Simple Communications Controller for an Dell Optiplex GX110 that is running Windows XP Home edition.
I have installed a Dynex data/fax/voice modem that supports Windows XP, but the system does not recognize it because of the drivers needed for the PCI controller.
View 7 Replies
View Related
Oct 12, 2010
After installing Win7 Ultimate 32Bit on my inspiron n5010 i installed all drivers and components are working properly but one of the devices have problem because i cant find any drivers for it. that device is " PCI Simple Communications Controllers" and it marked in Device manager with yellow symbol and the Update Driver button in Device manager does not work for this.
View 12 Replies
View Related