Cisco :: WS-C2950-24 Separate Guest Clients From Domain On Network?
Jun 8, 2012
I am playing around with a WS-C2950-24 running IOS 12.1(22)EA13. I would like to separate guest clients from domain clients on the network (for a start) so that guest clients only get access to internet and i have created three vlans for this purpose. Vlan 10 - internet, vlan 20 - internal, vlan 40 - guest. I have also set up a trunk link on the internal network.since the 2950 does not offer routing capabilities i assume i need to to the routing between these networks on another box. I am planing to do this on a linux machine. I have set up the same vlans on the linux box.
My question is how do I configure the cisco correctly so i can reach all the networks on the linux box. The cable that runs between the cisco and the linux box is connected to vlan 20 - internal and is defined as a trunk port allowing all vlans ( switchport trunk allowed vlan all ) with vlan 20 as native.it looks like only vlan 20 is using the cable that reaches the linux machine. 2950 ----- unmanaged switch (not replaced yet) ---servers
View 9 Replies
ADVERTISEMENT
Oct 17, 2012
Any problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies
View Related
Feb 8, 2012
I have a wrt54g router and would like to separate the WLAN clients from accessing computers and servers on the LAN... in other words I would like to make it a "guest" network. I've put the router in "router" mode instead of "gateway". I just want to be sure if that is the best thing I can do in terms of turning the wireless network into an isolated one.
View 4 Replies
View Related
Jul 3, 2012
I've got an E4200v1 running 1.0.04 firmware with guest access enabled. I'd like to find out who is logged in using the guest access. Is there a way to get a list of the DHCP clients on the guest network? I'm able to do this for the non-guest access via the WEB interface's Status->Local Network->DHCP Clients Table page. But I can't find a similar table for the guest network.
View 3 Replies
View Related
Dec 11, 2012
how to setup a separate SSID for guests (without a password).
Basically, we have one SSID now called Mnet which has a WPA2 password. For guests coming in i want Mnet Guests where people can connect without needing a password. They should be able to use internet but not connect to LAN devices, how to accomplish this with this WAP321?
View 7 Replies
View Related
May 9, 2013
We have;
3 - 5508WLC
1 - 4402 WLC
Cisco Prime 1.3
25 - 3502i
We have 25 remote sites that use MPLS back to the company HQ that has one connection to the internet.Also at the HQ we have a seperate ISP connection.The remote sites and HQ have AP's which provide internal company access. We would like to have a seperate Guest WLAN at these remote sites to provide access to the ISP connection at the HQ's. Do we need to have an anchor controller? From documentation I have been reading it looks like anchor controllers are mostly used for networks that have a single connection to the internet and they use the FW to control/ secure the guest and company network from each other. Is there a differnt way of seperating the guest wireless and company wireless network securely from each other but use the same WLC's and AP's??
View 6 Replies
View Related
Sep 12, 2011
i have two WAP4410N wireless router. with software version (2.0.1.0) , here i have a problem on SSID broadcast and access.i have created Two ssid's WC72 and SREE with same security configuration WPA2-personalmixed . i cant see the broadcasted SSID of name SREE where i only view WC72 and get connected to it..
where i initially want is separate SSID and internal network access for internal employees and Guests (shouldn't connect to internal network).
View 9 Replies
View Related
May 28, 2013
I have a WLC 2504(code 7.0.235) installed and two AP 3502 (local mode). RADIUS Server is a IAS runnning on my AD server.
I had a domestic AP before Cisco solution, using the same RADIUS server and everything was ok. After migration Windows 7 domain clients and Apple devices connects without issue. However when I try to connect non-domain windows 7 clients into wireless network (802.1X) and got failure. Apple devices out of domain can connect, certificate pop-up appears and connection flows.
I check certificates and everything looks ok for me. I remove a windows 7 client from domain and test it too, an got the same error. Certificate are install on windows 7 clients.
Could Cisco controller interfering in this authentication process ?
View 1 Replies
View Related
Jun 16, 2012
How to check applied group policy on the domain clients
View 1 Replies
View Related
Jul 10, 2011
which is the maximum number of simultaneous wired guest clients on a 5508? And in a 2112 controller?
Wired clients count as wireless clients??
What about anchoring limitations, what is the effect of wired guest clients on the anchor controller?
View 2 Replies
View Related
Jan 26, 2011
I would like to put an E2000 in an office where clients are coming and going throughout the day. When the documentation says that there is a maximum of 10 guest network users allowed (with a default setting of 5) what exactly does that mean ? I don't want the first 10 guest-clients who come in, connect to the guest network, then leave the office to consume all 10 slots for the day.If I have 50 people that come and go from the office throughout the day who connect to the guest 192.168.33.X network and attempt to enter the password (but no more than 10 guests authenticated at any given time) will all 50 be successful in connecting ? Or do I have to reduce the Client Lease Time to something less than the default setting of one day ?
View 1 Replies
View Related
Jun 18, 2012
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
:
ASA Version 7.2(4)
!
hostname ASA
domain-name default.domain.invalid
[code].....
what I need to add to get the vpn client to be able to ping the router and clients?
View 3 Replies
View Related
Oct 30, 2012
with our WLC 5500 controller, once the clients get the DHCP address the page is not redirecting them to the guest portal.What is the best way to check as to why the redirection is failing.
View 8 Replies
View Related
Apr 4, 2012
I have 4 computers (3 laptops, 1 desktop) in a shared office. We get internet access using their wireless network. All works fine. However, I need to share a printer amongst all of the computers. The printer is LAN enabled and I would normally just put all the PCs on a hub, together with the printer and share it that way. BUT my question is can we access the internet using the wireless network and the printer using a separate wired network at the same time?
View 7 Replies
View Related
Apr 2, 2013
I am looking for some information concerning network adapters. Many server vendors (HP, Dell, IBM and so on) use multiport single network adapter (one card,several ports -let's assume 4 ports). What resources are shared in multiport solution? For example:
- does multiport nic has significant limitations? For example, it's cpu cannot handle full 4-port load?
- interrupt sharing?
- buffer size?
View 3 Replies
View Related
Oct 10, 2012
What image i would need for my 2950 to enable DHCP snooping and DAI features (just for lab purpose)?
or are these features just available on the bigger modular switches (4500 and 6500)?
>sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA8a, RELEASE SOFTWARE (fc1)
[Code].....
View 4 Replies
View Related
May 26, 2013
I have a C2950 Switch & I am trying to upgrade the IOS version of it so that I can proceed with learning about SSH. My current version of 12.1 does not have Enhanced Imaging. I am so new to Cisco, that I have spent hours trying to find the correct page, or link, or anything that can enable me to upgrade to a later version.
View 6 Replies
View Related
Jan 7, 2012
I am running DHCP snooping for VLAN 1 on below switch
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA4a, RELEASE SOFTWARE (fc1)
Model number: WS-C2950-24
Looks like below IOS does not support snooping.
Model number: WS-C2950-24
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(14)EA1a, RELEASE SOFTWARE (fc1)
View 3 Replies
View Related
Sep 16, 2012
I using IOS c2950-i6k2l2q4-mz.121-22.EA14.bin but no support command "ip http secure-server" and I not connect switch by CNA. How I fix ? Or IOS C2950 support ip http secure-server and ssh ver2 ?
View 1 Replies
View Related
Jan 16, 2013
My fiance recently signed up for the Screen-wise Panel for Google research. Basically they monitor your TV usage and your internet usage. As part of the program they installed a Cisco WIFI router. I've got no issue with them logging the sites visited etc but I'm a little worried about them possible collecting private information (banking / work related stuff) that I don't want going out there. According to what I've read what's supposed to happen is they replace your router with the new Cisco router.The "technician" who came in and installed the router was actually a builder and not an IT technician and rather than replace our router he connected the Cisco router into port 4 of our router... I wasn't in at the time.
What I was looking to do is separate Port 4 of my router into a separate VLAN that can access the internet, but not access anything on ports 1-3, or the wireless. However, I want to be able to see everything on port 4 from the other side (in other words I want to see "into" the port 4 VLAN, but don't want them to see out). I also wanted DHCP to assign IP addresses correctly depending on where you were plugged in. In this example the first VLAN (your current router ip address) is going to be on 192.168.1.1, and the second VLAN (the new on we create on port 4) is going to be on 192.168.2.1.This is exactly what I'm looking to do, I could then connect the kids machines / tablets / ipods to the Cisco router and have the main machine and my work laptop on the main router... but I don't have a clue how to do it. </quote> Is this something that I am able to do with the Netgear router I own and is it hard to set up?
View 1 Replies
View Related
Mar 27, 2013
i have computer A with 2 NICs.... NIC 1 has ip 192.168.x.x which has access to internet and NIC 2 10.0.x.x which as access to server files and other docs....i have computer B with ip 192.168.x.x but want to be able to access 10.0.x.x using computer A as a router is this possible and how do i go about doing that. i was thinking about bridging NIC 1 and NIC 2 adding static route on computer A and adding a second ip 10.0.x.x to computer B NIC (i know it is possible to add 2 ips on one NIC in windows) so i can have access to the file server...is what i mention possible
View 1 Replies
View Related
Jun 25, 2012
The current setup is as follows: Virginmedia Superhub in modem mode connected to one Cisco C2950 on port fa 0/23. The 2950 is connected to a Cisco C3550 over fa 0/24 via normal Cat 5e.Port fa 0/23 on the 3550 have a Astaro/Sophos UTM connected to it that acts as a Firewall/Wireless controller etc. The hitch, or maybe one of them, is that the 3550 and the UTM is on another floor from the 2950 and cannot be moved. The Virginmedia superhub can't be moved to the other floor either due to limitations in the cabling.What I'd like to achieve is for the UTM to pick up the public IP from the Virginmedia cable modem whilst no other devices on the Lan should be able to connect to the cable modem. All inbound/outbound internet traffic should go through the UTM for security reasons. The UTM have a number of available nic's that can be set to dhcp, static etc. I already have a number of VLANS on the router/switch and have half a suspicion that using another VLAN for this purpose might be the way forward but I'm not sure..
View 3 Replies
View Related
Jul 22, 2011
I have build topology like this:
host------c2950(f0/3)------(f0/4)c3550(f0/41)----modem-----Internet
I wanted to monitor c3560 port where modem is connected from host. So for that I configured rspan. configurate show below. But problem is that after configuration f0/4 of c3550 remains up and f0/3 of c2950 goes down. WHen I look at status of f0/4 it show "FastEthernet0/4 is up, line protocol is down (monitoring)". I tried to search websites It seems configuration is fine.
[code]...
View 1 Replies
View Related
Feb 4, 2013
Internet connection come from an ethernet port in the wall. Cat 5 then goes to the switch and then to various computers.Desktop #1 has a IP of 10.1.1.133, sub 255.255.255.0, default gateway 10.1.1.200, DNS 10.1.1.4I want to be able to attach a cat5 cable to the LAN port of a Linksys WRT 54G going from the switch.What is the settings I need to select in the Linksys router for this to work.DHCP - Off. I guess the LAN IP of the router must fall in the range of the Main DHCP pool. Could I select anything in the 10.1.1 100's as long as another computer did not have the same IP. The starting IP of the linksys router stays in 192.168.1...... and doesn't looked like it can be changed. Does any Laptop that connects wirelessly to the linksys router need a static IP or can it obtain an IP address through
View 14 Replies
View Related
Feb 2, 2013
I have a DSL modem with wireless networking, and I am trying to install a second wireless router for a separate network. The standalone wireless network has five laptops networked to a sixth laptop, in a server/client setup. To complicate things, I am plugging the server laptop into a LAN connection on the DSL modem. The server shows both the LAN connection with internet access, and the second wireless network without internet access. The client laptops just show the wireless network, without internet access.
This is exactly what I need - internet access for the server but no access for the five clients. I have each wireless router on a separate channel and only auto connect to the standalone wireless network. Is there anything I need to do to the setup of either of the routers to avoid problems?? The wireless network without internet access seems to be abnormally slow in response and I am wondering if there is any interference between networks. None of the laptops are accessing the DSL wireless network, but I still need that DSL wireless capability for other computers in the building.
View 2 Replies
View Related
Oct 25, 2011
I have about a Netgear WGR614 router and a few CentreCom FS708 switches.Is there a way to create a home network so every safe an secure computer can access the internet and another network where I would fix machines that have virus's or machines that I don't want to access the home network.
How would I go about doing this? Or do I need a better router with DD-WRT installed on it?
View 3 Replies
View Related
Sep 26, 2012
How do I configuring Private Class A [10.206.90.0/24] and Private Class C [192.168.1.0/24] Network on Cisco 3550-12G Switch.
View 3 Replies
View Related
Jan 25, 2012
I use a C2950-24 switch, with IOS 12.1(22)EA12 release.When I try to connect in console mode, I can see the "Press RETURN to get started!" message, but it's not possible to me to have the # prompt.An "authorization failed" message is displayed. And the same message is prompted.
I try to recover password by following the recovery procedure. After the boot command, I never see the message "Continue with the configuration dialog? [yes/no]: ".
View 6 Replies
View Related
Nov 10, 2011
How can i use a router to extend the ip addresses of a separate network? I have been given a subnet mask of 255.255.255.248 which has given me 6 ip addresses to access the internet. How can i use a router to allocate extra ip addresses and route them to the internet ?
View 1 Replies
View Related
May 7, 2011
I've got a business network that I'd like to separate two sets of computers all together (thinking through a firewall rule or other method). Here's a text example of what I want to achieve:
Group A: PC 1, PC 2, PC 3 (can see each other and share files within this group)
Group B: PC 4, PC 5, PC 6 (can see each other and share files within this group)
But Group A & B can not see each other and are blocked from accessing each other.Can this be done with the DIR 655 or do I need to upgrade? Also, these two groups will be sharing the same internet connection.
View 2 Replies
View Related
Sep 30, 2012
I've just started out playing with a Cisco 1800 router to gain some knowledge of Cisco devices before taking a CCNA. I also have a 2950 switch but will start with the router.
I'm using an Android phone as a wireless Internet access point. This issues IP addresses by DHCP in the 192.168.43.x range with 255.255.255.0 subnet.
Also I have a Linksys WRT54G router running DD-WRT firmware acting as a wireless bridge to the Android phone, and it has 4 LAN ports.
This bridge is up and running and I have successfully connected my laptop to the Linksys for testing and can use the Internet provided by the phone.
Connected to the Linksys is a Cisco 1800 router. Connected to the router is my Citrix XenServer PC and a NAS box.
The XenServer and NAS are on another network 07.05.19.x range with 255.0.0.0 subnet using their own static IPs. One of the virtual clients on the XenServer will be a DHCP server to service other virtual clients. All still in the 07.05.19.x range.
Basically I want the devices on the 07.05.19.x IP range to be able to use the Internet gateway at 192.168.43.1 to access the Internet.
How would I set up my 1800 to achieve this?
Also, am I right in understanding that the 1800 will ignore DHCP leases from the Android phone due to it being a Layer 3 device.
View 4 Replies
View Related
Mar 29, 2011
i want to know how to access printer remotely,mean when the user is not in the network. .in domain network
View 1 Replies
View Related
Jun 13, 2012
I have a 4-port Netgear modem/router (DG834), and need to distribute its Internet connection according to the following criteria:
1.There are 11 access points (3 wired, 8 wireless) across 4 floors of a building - all cabling is from a central point, which will connect through a switch.Cat 5e cabling is in place.
2.The wireless points need Power over Ethernet connections
3.The 4 router ports serve 2 PC's and a printer in an office, the fourth being the connection to the switch.
4.There must be network separation so that:
- all points have Internet access
- there are three separate groups - one for the office, one for staff (wired) and one for guests (the wireless points), the purpose being to ensure that no user in one group can access any user's device in the other 2 groups. I'm assuming VLAN is the method for this.
5.Traffic on the network is likely to be fairly low casual use of the wireless ports, the office PC's only being used for Internet access and email no transactional systems, large databases or other resource / network-intensive functions.
1.Both the Netgear FS726TP and GS724TP look as if they will do what I want, using WNAP210 wireless access points. Could I achieve the same outcome with 2 x GS108PE switches? Any other hardware recommendations?
2.Do I need any additional hardware?
3.Are there any other considerations I have not thought of?
View 10 Replies
View Related
