The last shipment of 3602 APs for a customer came with 7.3 software. Controllers are running 7.2.110.0 so APs had to be downgraded. After APs finished downgrading they were still up. When we moved the APs to another controller running 7.2.110.0 they would not come back up. Power was denied at the switch.
View 2 RepliesHave a Cisco 2500 WLAN with Cisco 1142 Lightweight Access Points.IOS: WLC & AP IOS is 7.4.100.0
Seems to be when the APS reboot or lose power we cannot issue command to bring the APs back up from the WLAN- we have to log onto each AP via a console cable and bring the interfaces up.
We currently have around 150 2975 switches and have had problems with it them not handing out PoE power to the cisco phones and access points at random times. There is plenty of power left for the switch to use. We have at least 15 that will be running fine for about a week and then all of the devices that use PoE power will shut off and will not come back on until we reload the switch. If you console in there aren't any messages that pop up and if you look at the port it just shows on connected or will show IeeePD in the power inline. We have contacted Cisco TAC and they just RMA them.
View 6 Replies View RelatedIs 802.11ac wireless module for Cisco Access Point 3602 is available to order ? what Wireless controller we need to use for the support of 802.11ac wireless standard ?802.11ac will support only on 5700 series wireless controller ? Or it will support with 5508 Series also ?
View 7 Replies View RelatedIn my log I have the message: "Access denied to wireless system with MAC address 0020008E971E". When I checked the vendor for this MAC, it shows Lexmark international inc, which fact make me feel something is wrong. My first thought was that somebody trying to break into my net but I am close to accept that the owner of Lexmark WiFi printer without an idea in networking, just tried to connect it to his network and after failing to do that, it's wired and wireless features are still on. But still could this be bug or something? I am posting some logs when I first discovered the problem and after I granted access to the device with the MAC address 0020008E971E. I forgot to tell you, that before I decided to post here I did firmware upgrade from Hardware version A3 1.10 to 1.35NA (I bought it from US) with factory default restore. The result was absolutely the same - the messages kept coming "Access denied to wireless system with MAC address 0020008E971E". So I granted access to that MAC and checked the logs again. There is a line in the log that stated "primary:"
View 7 Replies View RelatedI have a EA6500 with a hard drive connected to the USB port. When I try to copy a file to the drive VIA the network folder on my computer it says "Destination Folder Access Denied, You Need Permision To Perform This Action". I used to be able to copy files to the drive so I am sure it is just a setting on the router or something.
View 5 Replies View RelatedI just bought a WMP600N adaptor and although windows 7 recognizes it I would like to install the official drivers from Linksys. When I try to update the drivers that I downloaded from the linksys website I het an access denied error. I am logged in as the administrator. I have already tried uninstalling the default drivers, but still I get the access denied error. I even tried the windows safe mode and still got the access denied error.
With the default windows 7 drivers the connection is quite poor. how I can install the official windows 7 drivers?
I configured my ACS 5.1 correctly, but I get an "Access is denied to NCS" at the web login page. In the ACS i see a successful authentication.
View 14 Replies View RelatedNETWORK CONNECTION PROBLEMPOPUP ERROR states"\<name> is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Access denied."When trying to View the two PCs through My Network Places> View workgroup Computers in MSHOME?I was able to map the shared folder manually.
View 1 Replies View RelatedI have a computer with windows 2003 server installed on it. There is one shared folder. The computer's name is SERVER. The shared folder's name is OFFICE.Whenever I type \SERVEROFFICE in a windows explorer window, I get a pop up window with a message that says that Windows does not find \SERVEROFFICE.I mean, I should be able to see the folder in this way because this OFFICE folder is shared and I am doing this from the same computer and not from another computer in the LAN.
View 3 Replies View RelatedI'm trying to solve a disastrous networking (via workgroup nightmare) and I cannot enable the DNS Client on my Windows 7 PC. I go to cntrl panel, admin services, dns client, and try to change it to automatic and it says "access is denied"
View 1 Replies View RelatedNetwork access denied for a particular folder
View 1 Replies View RelatedXP desktop hard wired to router. XP and Vista laptops wireless. Vista has SP1 and both XPs are SP3. All computers can see each other. Vista can access the XP drives. The 2 XP computers can access each other. The 2 XP computers cannot access the VISTA. Access is denied. Firewalls are off on all computers. I have tried permissions on both sharing and security tabs with no luck.
View 14 Replies View RelatedWe have a Cisco ASA5505 here that provides DHCP and routing to all our devices in our network. We also have a few other switches and wireless access points connected directly to the back of the ASA5505.For the past year all the wireless network signals has been working fine however starting last month, none of the wireless access points (we have three WRT54G) would allow proper connection (dropping connection, slow internet).I thought this maybe all THREE wireless access points are toast/bricked. So i went out and bought brand new Netgear WN604 and even with the new WAP i'm having same connectivity issues (really slow internet).When hardwired directly to the switches we get BLAZING fast internet & connectivity, no issues.
I called CISCO TAC and they automatically said "our ASA5505 is fine, it has to be your wireless access points" not working properly. I explained to them that i also purchased two brand new access points and they are doing the samething now, how can that be?
I've had some long standing issues that I've tried various things to fix. I have two WAP4410N access points set up at a smaller sister company. Wireless clients (laptops) are not receiving DHCP assigned IP addresses. If I type in an IP manually, it works fine.The sister company has a point to point T-1 connection to our main building. Our main building has the DHCP server. The router on the sister company end is configured as the DHCP relay.
I've upgraded the firmware three different times in the past to hopefully resolve the issue, but no luck. Just today, on one of the WAP4410N's, I upgraded to the 2.0.6.1 firmware (backing up config, reset to factory default, upgraded firmware, reset factory default again, restored config). After the first reset to factory defaults, the Access Point itself picked up a DHCP address from the server, and I verified this in the DHCP console on the server, so I know that the DHCP relay is working. However, my laptop would not get a DHCP address when connecting wirelessly through that access point. It is a Windows 7 Enterprise laptop. I also could not get a DHCP IP with my iPhone connecting to wireless, to rule out specific issues with just a laptop.I have the DHCP lease times for the subnet that these WAP4410Ns are on set to 2 hours.
To put a cherry on top, there is one laptop that stays in a lab area at all times, connecting wirelessly, and it DOES get a DHCP IP address (I can see in the DHCP console that the lease for this laptop continually renews as needed). I do remember on initial config when I couldn't get it to work, that I did a manual set up, gained connection, then switched it to DHCP...but that doesn't work for any other laptop.Why would the access points get DHCP address, but not anything connecting to the Access Points?
Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
At my school we have a lot of access points, but sometimes the computer use the wrong access point. How can I solve that? Is there a program for switching access point?
View 8 Replies View RelatedBTW the halls are next to each other.The house and the 3 halls are in the vicinity however not attached together(i.e. wall to wall). The distance between the house and the first hall is approx 1 road width distance.ISP is Virgin and the internet was installed this year hence has the latest Virgin Home Hub.I am aware that i probably require 3 wireless access points (1 for each hall).The first wireless access point will need to be connected with a RJ-45 cable running from Home Hub. Can i connect the Wireless access points up together or do they all need to come from the ADSL hub?I am not sure what Wireless access points would be best and how to go about connecting this all up
View 2 Replies View RelatedI have New Pace 4111n Wireless Router that I got from AT&T and is setup on 1st floor, but its wireless range does not get me to 2nd floor. I also have the 2Wire wireless router from AT&T. In Addition, I have ethernet connection from level 1 to level 2 as well.
I was wondering if it is possible to have the Pace Wireless N router to work as modem and wireless access point, at the time use the 2Wire router to broadcast wireless and act as access point for 2nd floor.
IF its doable, how should the two be configured and connected.
I'm configuring ASA 8.4 for SSLVPN allowing Web Portal access with group-url. I've noticed that if I put certain keywords after slash mark on group-url, client access would be denied by http 404 error.
Here's my configuration:
tunnel-group test type remote-access
tunnel-group test general-attributes
default-group-policy test
[Code].....
i tried all the possibilities... still i'm getting the same error.
View 3 Replies View RelatedI have enabled Network filtering on MAC address on my D-Link 628 router.
I've noticed entries in the log file - "Access Denied to LAN System with MAC address ______________" for 2 different MAC addresses. I do not recognize these MAC addresses. The entry that immediately follows these messages - "Above message repeated 466 times and 124 times. The entries for these 2 MAC addresses has been occurring multiple times with different repeat numbers over the past few days.
Is this an indication that someone nearby my router is attempting to hack into my wireless router or do I have a configuration issue?
I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty registering the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch. A bad update was not allowing the access points to get their correct firmware.
View 7 Replies View RelatedI am having an issue here. I have 2x 5508 that each have 100 AP license and a little under 200 access points. Basically all of the access points are using DNS to connect to the primary controller that has the DNS entry. Basically half of my access points need to be on the second controller and in order to do this I have been using the high availability mode of each access point to push them to the second controller IP address.It was working perfectly until now. I have pushed 28 access points to the second controller and the last two I need to push at this location just keep resetting on the primary controller. Neither controller is configured as master controller.
View 4 Replies View RelatedI need an Wireless Access Point.Two SSID simultaneously in different IP Rangeit is with a simple browser GUI to manage? (not console and controller)a distance of about 50 (we can place multiple APs)N speedDual BandWhich series meets the above requirements?It can also Wireless-N Gigabit Router as 4400N, but it does not support Dual Band.
View 1 Replies View RelatedI have access points deployed across several buildings that each have a different IP scheme and their own T1 line. Is it possible to configure the 5508 controller to allow these access points to use the IP scheme assigned for that particular building or will dhcp always assign an IP address to the connecting client based on the IP scheme of the building that the controller resides in?
View 1 Replies View RelatedI need an official document from Cisco saying the APs models supported by the WLC 5508. Specially, I need to know if the AIR-AP1242AG-T-K9, converted from standalone, will be supported by the 5508.
View 1 Replies View RelatedWe have a couple of Access Points which are not registering with WLC 2500. I followed-up on the two LAPs in the dorm. They were cycling through red, amber, green, indicating they were trying to join the controller but could not.
Recently, we have changed our IP Schema for the Wireless Devices and I believe there is an IP Conflict between APs and WLC. Earlier APs were cofigured with Static IP Address assignment, thus they can't change their IP Address.
how to reset the Access Point? I know we can hard reset them by pressing the Mode button manually.
Is there another way via which this can be done witout removing the Access Points from their enclosures?
I have multiple cisco 1130ag access point at one of my clients villa. The issue I am facing is when moving throughout the buildingthe laptop and smartphones will not switch between AP’s unless it loses its connection with its existing AP then it will see the other AP that is closer and connect to it.
For example, I start at one end of the building where it connects to AP#1 , if I then slowly go to another section of the villa, it it will not switch over to AP#2 until the signal is lost from AP1
I have following settings
AP's are Cisco 1130AG
Single SSID with WEP Security
install AP1042N access points?
Situation: I have a store where there is already installed an AP1042N. In the back of the building there is no wireless signal. I want to install a second access point to extend my range;
At home, I use my laptop to connect to my wireless router without any trouble.But at: public libraries, Starbucks, hotel rooms... any free public wifi? All attempts to connect meets with the same error: "unable to connect to network" (preceded by the system hanging for a lengthy amount of time). Windows advises me to unplug the router and plug it back in, which obviously isn't an option.It's annoying to troubleshoot, because I'm only having the problem at times where I have no wired access (hence: no way to get to forums like these and look for an answer, update drivers, whatever).
View 6 Replies View RelatedI manage Wi-Fi on a college campus, and we have implemented 802.1x with RADIUS authentication running on a Windows server, and that works well. The issue is that the college is looking at removing wired connections in the dorms in favor of just deploying wireless, and the gaming consoles (Xbox, PS3, etc. ) cannot support 802.1x. We use Cisco 5508 Wireless LAN controllers with 1142 and 3602 APs.
I would like to enable MAC address authentication for these gaming consoles, wherein we (IT) would enter the MAC address of the console for a single connection and allow that console to connect to Wi-Fi, but I do not want to use WEP or any other TKIP passwords, because once the students would know the password they would use WEP/WPA instead of authenticating through RADIUS for their PC/tablet connections. .
i m working in a domain environment . for example my domain name is testdomain.com. i create a shared folder on it and give everyone a read control over it. then i create a folder in that shared folder with name of test. i also create a user with name test. i give full control to test user over test folder. now when i access the test folder from network with username test. i can read that folder but when i create the file or folder in the test folder it will show the following error..."unable to create a folder"new folder" access is denied.
View 1 Replies View Related