Cisco Wireless :: AP1262N Repeater SSH Web Configuration Interface Not Reachable After Alignment
Jan 14, 2013
we have a couple of AP1262N-E-K9 APs with firmware version 12.4(25d)JA1 operating in autonmous mode. One AP is setup as repeater while all others are in root mode.
The repeater has setup one parent MAC address so it associates every time to the same parent root AP. Given this setting, I am logging into the repeater via SSH and start the antenna-alignment scan: "dot11 dot11Radio 0 antenna-alignment timeout 4"
During this scan, the repeater disconnects from its parent to perform the scan so no output is visible at the SSH console. After the scan is finished, the repeater re-associates to its parent and some output appears on the SSH console.
8 of 10 times this procedure works fine: the scan is finished and I can continue entering commands on the SSH console. However, in some cases the repeater is not reachable any more for about 7 minutes. I.e. pings to the repeater's IP address are unsuccessful and the SSH connection hangs until it is automatically disconnected after a timeout. Also, the web configuration interface is not reachable. After about 7 minutes everything works fine.
View 7 Replies
ADVERTISEMENT
Jan 16, 2013
we have a couple of AP1262N-E-K9 APs with firmware version 12.4(25d)JA1 operating in autonmous mode. One AP is setup as repeater while all others are in root mode. My goal is to perform the antenna-alignment test through an SSH console on the repeater with a given timeout-value, e.g.:
"dot11 dot11Radio 0 antenna-alignment timeout 4"
However, the behavior of this command is inconsistent as the timeout value is ignored in 20% of the tests. I.e. in 80% of all tests, the scan really runs only 4 s as specified using the "timeout" parameter. In the other 20% of the tests, the "timeout" parameter seems to be ignored: Often the antenna-alignment scan runs for about 140 seconds and in some cases even for 420 seconds. This is problematic as the access point is completely unavailable during the test, i.e. the configuration ssh/web interfaces are not reachable and no clients can associate to the access point. [URL]
View 3 Replies
View Related
Mar 26, 2012
Recently installed a 1262N AP in autonomous mode. Have both 2.4 and 5Ghz radios running- Both on separate SSID and VLAN. I think I have 5Ghz channels using 40Mhz bands (bonded) but when I do iperf throughput test I only get about 25Mb throughput. I am sitting within 10 feet of the AP. When I switch to 2.4 I get around 60Mb and that's not bonded. I have tried multiple interfaces on my client side laptop I'm testing with since I thought maybe it was a quirky card or driver but I get same results. Am I doing something wrong here? My laptop shows a 300Mb connection to 5Ghz and 144Mb on 2.4Ghz but I know that's not true thorughput so that's why I was testing this to see what I was really getting and now I'm confused.
View 4 Replies
View Related
Feb 2, 2013
From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.
View 5 Replies
View Related
Aug 13, 2012
We have 400 branches is ended on ASR 1002 router. ASR 1002 is the Hub router. When we disconnect/connect WAN interface or Shut/no shut tunnel interface, at the moment, router is not reacheable via telnet.
But if i disable the EIGRP on tunnel interface, tunnel are ok, then when i enable eigrp on tunnel interface, all eigrp neighbourhoods are OK.Is there any way to limit NHRP or EIGRP packets ?
View 1 Replies
View Related
Dec 10, 2012
I would like to provide WiFi in a big house of 4 floors so I have installed 1 WAP4410N wired to the Internet router to act as access point and I have configured 3 others WAP4410N as WDS repeater of the first one.In the first one (the AP), I have checked the option "Allow Wireless Signal to be repeated by a repeater" then entered the 3 repeaters' MAC addresses as allowed devices to repeat the signal.
Is that configuration OK ? Is there any way to add another (a fourth) repeater to this configuration ? Because there is only 3 fields to specify allowed repeaters' MAC addresses in the AP.
View 2 Replies
View Related
Sep 4, 2012
configuration WAP4410n.I configure 1 wap4410n mode access point, is ok.I place 6 wap4410n in building as wireless repeater.I can not configure the right sequence.How do I set up 6 repeaters with access point ?
View 2 Replies
View Related
May 1, 2012
For the establishment of a WiFi Hot Spot with 5 Cisco 1242AG and 5 antenna AIR-ANT1728, I want to know what the config is the most suitable.
- One antenna in root mode and the other 4 in repeater mode
- Or 5 antennas in root mode
Between each terminal distance is about 100 meters outside?
View 3 Replies
View Related
Oct 27, 2012
I am using two Cisco Aironet 1252 (cisco AIR-AP1252AG-A-K9) to setup a point to point link (one is configured as root bridge and is as a non-root bridge). Both Aironets are running software version Version 12.4(25d)JA.
Is there a way that I can that I can perform an antenna alignment test on the Aironet that is configured as a non-root bridge?executing the following command dot11 dot11radio 0 ? does not show the antenna-alignemnet option.
View 11 Replies
View Related
Oct 30, 2012
My current setup is an AP1262n located ~400 feet from my WAP321. I would like to take the wireless signal coming from the AP1262n and rebroadcast it using a WAP321. configuration setting on these two devices.
View 2 Replies
View Related
Dec 17, 2012
we have purchased a couple of new Aironet APs for our office:
AIR-AP1262N-E-K9
My objective is to use some of these as wireless monitors to scan the vicinity and to report the SSIDs and RSSI values of all detected APs.
Basically something similar to the Linux command: "iwlist wlan0 scan".
Periodically, I would like to transmit the scanning results to a central server (e.g. via SNMP) for monitoring the whole network area.
Are there built-in commands in the IOS to do this? Or can I use Tcl scripts to perform this task?
I have worked with Cisco routers and switches before but I am new to wireless devices.
View 4 Replies
View Related
Jul 12, 2012
This is one of our first site where we are implementing Cisco wireless, and we bought some external Autonomous AP1262, when we should have bought Lightweight LAP1262 . We can get those replaced, but I am looking into migrating them in order to get them to register with our 5508 controllers.
There do not seem to be a migration tool to download for 1262. Must it be done via the WCS ?So far I have not managed to add these autonomous AP to the controllers. How to know if a migration toll exists for those !
View 4 Replies
View Related
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
Jan 10, 2013
we have a couple of AP1262N-E-K9 access point with firmware version 12.4(25d)JA1 operating in autonmous mode.
I attempted to measure the signal quality between the APs by setting one device to repeater mode while all others are in root mode. Then, I execute the following command: dot11 Dot11Radio 0 antenna-alignment
1. The output of "show dot11 antenna-alignment" is incorrect, the % value represents the signal strength in dBm without the - (minus). E.g. "-25 dBm" is displayed as "Signal 25% 0 dBm".Now, I know that is only a display error but still this is not clean. Is this a known issue?
2. Why are the measured signal strength values not displayed on the SSH console during the antenna-alignment test? Is it obligatory to use the console to see these values? Or is it also a known bug which might be fixed in later firmware versions?
View 2 Replies
View Related
Feb 7, 2012
I have a wap4410n. It was performing poorly. Only letting some computers on the wireless while not letting other. I was able to login into the device and I went through each of the settings pages to see if there was anything set wrong. I soon found there was a firmware upgrade available.
So over a wired connection I started the firmware upgrade after waiting 10+ minutes I was unable to reach the device and the web page said it was waiting for the ip address of the device. So I rebooted the device.
I can not ping the device. I can not see it on any subnet. I have tried the reset button multiple times.
The ethernet and power lights are on.
View 2 Replies
View Related
Feb 22, 2013
I have a big problem with my Cisco EA6500 router. I have a domain that is pointing to my public IP address of the home network. I have various computers and applications that listen on different ports for various reasons on this network. Everything worked fine until a week or so ago when I had to restart the router. The reason was that while I did a routine change (add a Mac filter for wireless) the router stopped responding. After restarting it, I could not access the home computers through the domain name (public IP) while being inside the network. If I try from outside my LAN it works fine but when trying from within the LAN the hostname and IP are not reachable. Also, everything works from inside the LAN if I'm using LAN IPs.
View 9 Replies
View Related
Oct 31, 2011
We have a Cisco 881 router, which is crashing. We have seen that the ARP cache fills up so much it causes things to crash, our phones go down.. We dont know why this however IP CEF seems to be doing it, when we disable it goes away however disabling IP CEF causes our L2TP tunnel to become inoperable also. So why does IP CEF cause thousands of AR entries and how can we limit that!? Below is the error, sample of the ARP cache and our config. You will notice we also have a /31 given to us on WAN interface, this was given to us by our service provider. This is really strange I cant find other examples on internet.
The error:
Nov 1 04:21:57.474: %SYS-2-MALLOCFAIL: Memory allocation of 65536 bytes failed from 0x81F083F4, alignment 16
Pool: Processor Free: 55176 Cause: Not enough free memory
Alternate Pool: I/O Free: 2352 Cause: Not enough free memory
[code]....
View 2 Replies
View Related
May 11, 2012
I'm reading this definition in the cisco T-shoot student guide:
"Align-Err: this is the number of frames with alignment errors, which are frames that do not end with an even number of octets and have a bad cyclic redundancy check"
I don't understand what "frames that do not end with an even number of octets" actually means. Did they mean even number of bits? or does a frame's lenght need to be an even number for it to be considered valid?
View 3 Replies
View Related
Aug 29, 2012
is it possible to manage a air-ap1262n with a controller like wlc 5500 or wlc 2500? the official cisco support could not answer me this question for sure. i have found this old guide to upgrade ap´s to lap´s, but there is hothing about the 1260 in it. [URL]
i am a little bit confused!
the cisco documents tells:
"at_a_glance_c45-636090.pdf"
A wireless network with standalone access points offers a low-cost, entry-level solution that does not require a controller. It is ideal for small-scale networks with less than 20 access points, and offers base-level wireless functionality with the flexibility to scale and add services over time by adding a controller.
View 4 Replies
View Related
Mar 17, 2012
How can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
View 9 Replies
View Related
Jul 6, 2011
how to get at the configuration interface for the "built-in" Twonky server on the E4200.Specifically, I'm trying to figure out how to get to the "clients.db" file and the area of the UI where I can configure the receiver settings. I'm getting the dreaded "unknown file format" message when streaming mp4 files to my Samsung BD-C6500 bluray player. Installing Twonky on my laptop and working with the problematic files has shown that the solution is a simple matter for BD-C6500 understand how the files are encoded.
View 9 Replies
View Related
Feb 6, 2013
I'm trying to configure a SG300 to be reachable beyond its own subnet. Its IP address is configured by DHCP to 192.168.2.2/255.255.255.0. It is possible to ping the switch from the same subnet but not from outside. The switch is set to layer 2 mode. All routing should be done by the gateway.
Here's what I have checked so far: The default gateway and netmask are set correctlyThe gateway can ping the switchHosts in the 192.168.2.0/24 subnet have connectivity to other networks through the gateway (i.e. gateway configured correctly)Administrative interface > IPv4 interface shows the correct ip address, netmask, and gateway (greyed out because it is assigned by DHCP)the switch can ping other hosts within the same network
Is there some kind of firewall setting that prohibits the switch to respond to ip packets from outside the subnet?
View 5 Replies
View Related
Jun 15, 2012
I need to connect 10 branches to a datacenter using cisco 861 routers because the ethernet sollution the provider gave us can't assign more than 32 MAC addresses for whe whole network. So we have all our servers at the datacenter with a central firewall/router and all remote branches with a static route to this router. We would like to make all branches local networks available through NAT or another better solution so network devices at the datacenter network can communicate with all local devices accross all the brances.
I've tried to set up a dynamic NAT from outside to inside the network and didn't work, set up static ip routes for both datancenter and remote branchs and also didn't work. I just would like to make the routers work in a transparent way, no blocking of anything, passing all traffic in and out the network.
View 7 Replies
View Related
Aug 16, 2011
On my server I host several websites.Last Monday we got our FttH-connection and I'd set up my D-Link DIR 655 to manage our server and other computers.In the webconfig of my router I set up the Virtual Server for several applications (Telnet - 23, HTTP - 80, HTTPS - 443, FTP - 21, SMTP - 25, POP3 - 110, IMAP - 143 and also ports 20, 22 en 81) redirected to my server's IP address.For these items the private port and the public port of each item is the same port number; the protocol is TCP for these items. I didn't change the options Schedule ("Always") and Inbound Filter ("Allow All").
The DNS of my domains (samendienen.nl and some other domains) is set to my new IP-address.May be I forgot some other settings in my D-Link-router.what I have to do to make my websites reachable?
View 6 Replies
View Related
Feb 14, 2013
The aDSL circuit is up and connected and I can reach the internet, however not all sites on the internet are reachable. This is occurring on two seperate 887VA’s and the circuit has been tested with a netgear router and no issues occur. The router has been tried on 5 different ADSL connections and the same problem occurs although more websites can be reached on a home broadband connection (ADSL2+ Annex A) as opposed to the problem being more severe on an ADSL2+ Annex M circuit. The problem seems to affect websites that are full of adverts more than sites that have single domain landing pages.
The sites that I cannot reach are pingable. This happens on multiple machines behind the router. The same config is used on an cisco 877-M router with no issues.
! Last configuration change at 14:52:30 UTC Wed Feb 13 2013
version 15.2
no service pad
[Code].....
View 8 Replies
View Related
May 6, 2013
I have one ASA with two tunnels. Each going to a different 3rd party Checkpoint firewall (site A, site B) Each site has two servers (A1, A2, B1, B2)I can only connect to A1 and B1. any connection to A2 and B2 fails. I have defined B2 and A2 in the crypto map to be protected.If I only have B2 or A2 in the crypto map ACL then the tunnel fails. Phase 1 does not come up. Its as if the ASA is ignoring the entries for B2 and A2.ASA running 8.4(2).I have also trashed the VPN and built via the wizard, same result.
View 12 Replies
View Related
Nov 29, 2012
I ve recognized some strange issue with LMS 4.2 , when the router becomes down or unreachable , the LMS doesn't send any event as Faultview,also when the router comes back online the LMS takes 1 hour to show its state as reachable.
View 3 Replies
View Related
Jan 11, 2011
I have windows servers connected on cisco switch 4500 series. Issue is when server NIC configure with Teaming, some times servers gets not reachable, and after restarting the servers it gets reachable. Is 4500 series switch support the teaming software?
View 3 Replies
View Related
Jun 1, 2013
I'm constantly seeing that the sync and replication status for my secondary admin/monitor node in the primary node as node not reachable. The secondary still thinks it is in standalone mode. When I run the ISE diag tool connectivity tests I am able successfully ping the devices from each other using both hostname and ip and the nslookup also works fine between both nodes. Ping and nslookups also work from different networks within the environment. The two nodes are in the same vlan on a 6500 vss pair but on different switches of the pair.
View 6 Replies
View Related
Mar 5, 2012
who to configure the interface of cisco 7606 router. As it is not getting up by doing normal configuration like "no shut"? iterface and line protocol both are down.
View 1 Replies
View Related
Jun 11, 2013
I have my hsp setup where switch A and switch B share active/standby roles among several vlans. In the last few weeks, i have seen trouble tickets where connectivity is lost and upon investigation i discover that i can ping physical interface IP addresses for both standby and active devices but not the standby IP. I have also validated configurations and layer 2 paths and they haven't been broken.
What I end up doing is failover to the standby device and back and the problem clears, reachability is restored. My question is whether I am solving this the right way. If so, what is it that would cause the standby IP to not be reachable and how does my solution fix that? N/B the switches are catalyst 6509's.
View 2 Replies
View Related
Jun 15, 2012
My customer they do not want change their real server IPs. So I need setup one interace (one armed) for them on ACE4710. Who had this sample configuration? (CSS has this but it seems to be not compitable with ACE)
View 4 Replies
View Related
Sep 30, 2012
Having a problem configuring my new 1941 Router. The 0/0 interface is attached to my broadband and gets it's ip via dhcp, the 0/1 interface is connected to my lan and has a dhcp pool. My problem is that the 0/0 interface does not appear to be getting any dns servers. So i have either missed something or need to add the dns servers manually to my dhcp pool. Below is my config,
[code]...
View 3 Replies
View Related
