Cisco :: LMS 4.2 - Takes Time To Remention Device Reachable
Nov 29, 2012
I ve recognized some strange issue with LMS 4.2 , when the router becomes down or unreachable , the LMS doesn't send any event as Faultview,also when the router comes back online the LMS takes 1 hour to show its state as reachable.
View 3 Replies
ADVERTISEMENT
Mar 24, 2011
We are using a service module with 4.1(1) that takes more more time to compile ACL.So we need to wait more time to permit and capture traffic.
View 1 Replies
View Related
Sep 25, 2012
When I start-up my computer, it takes over an hour to find my router on my computer (Not on my brother's computer, or the computer upstairs). Once it does, it connect perfectly. This is very annoying because I do not have a lot of time anyway to work/play and when I do, it takes over an hour to find the router.Recently, I have been having HUGE lag spikes, constantly disconnecting from games and skype calls.
View 1 Replies
View Related
Mar 14, 2013
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Region : Others
Model : TL-MR3220
Hardware Version : V1
Firmware Version : latest
ISP : Orange
The TL-MR3220 takes a long time to identify the 3g modem and sometimes it will not identify it at all and says "unplugged". Sometimes "unplugged" suddenly apears after the modem has been identified and was working properly.Is this the normal behavior of this device ? Why ? What can be done ? I'm Using Alcatel X500D 3g modem.
View 5 Replies
View Related
Nov 24, 2011
I have a Cisco Aironet 1200 Series Access Point. It takes long time to boot up.
After showing the warning banner message it takes long time before asking for username.
The sh version is given below.
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(7)JA4, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2006 by Cisco Systems, Inc.Compiled Tue 05-Sep-06 14:15
[Code].....
View 3 Replies
View Related
Sep 12, 2012
This is the great place for ACS discussions , i need two more inputs from experts
acsserver
Thu Sep 13 14:35:28 UTC 2012
pughaz
15
[ CmdAV=ip tacacs source-interface FastEthernet 0/1 ]
Device Type:All Device Types:ROUTERS, Location:All Locations:NON DC DEVICES
On the above message
1. Need to chang time from UTC to IST
2. The Device column is not showing the exact device name ; i telnet and config changed , it is showing the device group name only , how to get the exact device name i telnet on this message
View 1 Replies
View Related
May 18, 2012
My environment have two device ,a cisco css11501 and a cisco 2960 ,when I reboot CSS11501 then 2960 shutdown fa0/41
I command "sh logging | in 0/41" just up down two time,not five times in 10 seconds
.May 17 11:13:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to down
.May 17 11:13:19: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to down
.May 17 11:14:53: %PM-4-ERR_DISABLE: link-flap error detected on Fa0/41, putting Fa0/41 in err-disable state
.May 17 13:44:35: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to up
.May 17 13:44:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to up
View 4 Replies
View Related
Feb 6, 2011
I have the new E4200 with an attached 750GB hard disk.All works well, however the media server becomes unavailable most of the time and renders the device useless.
I can connect to the Media Server from my xbox and laptop for an hour or so, and then all of a sudden it is gone. The only option I have is to reboot the router to bring it back online however not all of the music and videos are shown on the media server (yet).I uploaded quite a bit of music and video to the hard disk, I can initiate a scan but after a while the media server becomes unavailable / cannot connect to it.
View 9 Replies
View Related
Feb 7, 2012
I have a wap4410n. It was performing poorly. Only letting some computers on the wireless while not letting other. I was able to login into the device and I went through each of the settings pages to see if there was anything set wrong. I soon found there was a firmware upgrade available.
So over a wired connection I started the firmware upgrade after waiting 10+ minutes I was unable to reach the device and the web page said it was waiting for the ip address of the device. So I rebooted the device.
I can not ping the device. I can not see it on any subnet. I have tried the reset button multiple times.
The ethernet and power lights are on.
View 2 Replies
View Related
Feb 6, 2013
I'm trying to configure a SG300 to be reachable beyond its own subnet. Its IP address is configured by DHCP to 192.168.2.2/255.255.255.0. It is possible to ping the switch from the same subnet but not from outside. The switch is set to layer 2 mode. All routing should be done by the gateway.
Here's what I have checked so far: The default gateway and netmask are set correctlyThe gateway can ping the switchHosts in the 192.168.2.0/24 subnet have connectivity to other networks through the gateway (i.e. gateway configured correctly)Administrative interface > IPv4 interface shows the correct ip address, netmask, and gateway (greyed out because it is assigned by DHCP)the switch can ping other hosts within the same network
Is there some kind of firewall setting that prohibits the switch to respond to ip packets from outside the subnet?
View 5 Replies
View Related
Jun 15, 2012
I need to connect 10 branches to a datacenter using cisco 861 routers because the ethernet sollution the provider gave us can't assign more than 32 MAC addresses for whe whole network. So we have all our servers at the datacenter with a central firewall/router and all remote branches with a static route to this router. We would like to make all branches local networks available through NAT or another better solution so network devices at the datacenter network can communicate with all local devices accross all the brances.
I've tried to set up a dynamic NAT from outside to inside the network and didn't work, set up static ip routes for both datancenter and remote branchs and also didn't work. I just would like to make the routers work in a transparent way, no blocking of anything, passing all traffic in and out the network.
View 7 Replies
View Related
Aug 16, 2011
On my server I host several websites.Last Monday we got our FttH-connection and I'd set up my D-Link DIR 655 to manage our server and other computers.In the webconfig of my router I set up the Virtual Server for several applications (Telnet - 23, HTTP - 80, HTTPS - 443, FTP - 21, SMTP - 25, POP3 - 110, IMAP - 143 and also ports 20, 22 en 81) redirected to my server's IP address.For these items the private port and the public port of each item is the same port number; the protocol is TCP for these items. I didn't change the options Schedule ("Always") and Inbound Filter ("Allow All").
The DNS of my domains (samendienen.nl and some other domains) is set to my new IP-address.May be I forgot some other settings in my D-Link-router.what I have to do to make my websites reachable?
View 6 Replies
View Related
Feb 14, 2013
The aDSL circuit is up and connected and I can reach the internet, however not all sites on the internet are reachable. This is occurring on two seperate 887VA’s and the circuit has been tested with a netgear router and no issues occur. The router has been tried on 5 different ADSL connections and the same problem occurs although more websites can be reached on a home broadband connection (ADSL2+ Annex A) as opposed to the problem being more severe on an ADSL2+ Annex M circuit. The problem seems to affect websites that are full of adverts more than sites that have single domain landing pages.
The sites that I cannot reach are pingable. This happens on multiple machines behind the router. The same config is used on an cisco 877-M router with no issues.
! Last configuration change at 14:52:30 UTC Wed Feb 13 2013
version 15.2
no service pad
[Code].....
View 8 Replies
View Related
May 6, 2013
I have one ASA with two tunnels. Each going to a different 3rd party Checkpoint firewall (site A, site B) Each site has two servers (A1, A2, B1, B2)I can only connect to A1 and B1. any connection to A2 and B2 fails. I have defined B2 and A2 in the crypto map to be protected.If I only have B2 or A2 in the crypto map ACL then the tunnel fails. Phase 1 does not come up. Its as if the ASA is ignoring the entries for B2 and A2.ASA running 8.4(2).I have also trashed the VPN and built via the wizard, same result.
View 12 Replies
View Related
Jan 11, 2011
I have windows servers connected on cisco switch 4500 series. Issue is when server NIC configure with Teaming, some times servers gets not reachable, and after restarting the servers it gets reachable. Is 4500 series switch support the teaming software?
View 3 Replies
View Related
Jun 1, 2013
I'm constantly seeing that the sync and replication status for my secondary admin/monitor node in the primary node as node not reachable. The secondary still thinks it is in standalone mode. When I run the ISE diag tool connectivity tests I am able successfully ping the devices from each other using both hostname and ip and the nslookup also works fine between both nodes. Ping and nslookups also work from different networks within the environment. The two nodes are in the same vlan on a 6500 vss pair but on different switches of the pair.
View 6 Replies
View Related
Feb 22, 2013
I have a big problem with my Cisco EA6500 router. I have a domain that is pointing to my public IP address of the home network. I have various computers and applications that listen on different ports for various reasons on this network. Everything worked fine until a week or so ago when I had to restart the router. The reason was that while I did a routine change (add a Mac filter for wireless) the router stopped responding. After restarting it, I could not access the home computers through the domain name (public IP) while being inside the network. If I try from outside my LAN it works fine but when trying from within the LAN the hostname and IP are not reachable. Also, everything works from inside the LAN if I'm using LAN IPs.
View 9 Replies
View Related
Feb 2, 2013
From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.
View 5 Replies
View Related
Jun 11, 2013
I have my hsp setup where switch A and switch B share active/standby roles among several vlans. In the last few weeks, i have seen trouble tickets where connectivity is lost and upon investigation i discover that i can ping physical interface IP addresses for both standby and active devices but not the standby IP. I have also validated configurations and layer 2 paths and they haven't been broken.
What I end up doing is failover to the standby device and back and the problem clears, reachability is restored. My question is whether I am solving this the right way. If so, what is it that would cause the standby IP to not be reachable and how does my solution fix that? N/B the switches are catalyst 6509's.
View 2 Replies
View Related
Aug 13, 2012
We have 400 branches is ended on ASR 1002 router. ASR 1002 is the Hub router. When we disconnect/connect WAN interface or Shut/no shut tunnel interface, at the moment, router is not reacheable via telnet.
But if i disable the EIGRP on tunnel interface, tunnel are ok, then when i enable eigrp on tunnel interface, all eigrp neighbourhoods are OK.Is there any way to limit NHRP or EIGRP packets ?
View 1 Replies
View Related
Jan 14, 2013
we have a couple of AP1262N-E-K9 APs with firmware version 12.4(25d)JA1 operating in autonmous mode. One AP is setup as repeater while all others are in root mode.
The repeater has setup one parent MAC address so it associates every time to the same parent root AP. Given this setting, I am logging into the repeater via SSH and start the antenna-alignment scan: "dot11 dot11Radio 0 antenna-alignment timeout 4"
During this scan, the repeater disconnects from its parent to perform the scan so no output is visible at the SSH console. After the scan is finished, the repeater re-associates to its parent and some output appears on the SSH console.
8 of 10 times this procedure works fine: the scan is finished and I can continue entering commands on the SSH console. However, in some cases the repeater is not reachable any more for about 7 minutes. I.e. pings to the repeater's IP address are unsuccessful and the SSH connection hangs until it is automatically disconnected after a timeout. Also, the web configuration interface is not reachable. After about 7 minutes everything works fine.
View 7 Replies
View Related
Sep 15, 2012
I had a strange issue with one of my customer..Cisco WS-C3750X-48P Access switch was not reachable and after reload it started working.I would like to know the root cause of the issue. There were no logs and no errors in interfaces.Even Cpu utilization was not high. We have enabled arp inspection and dhcp snooping in the switch..Hope this will not make any issue..Also we have dot1x enabled on port..
View 5 Replies
View Related
Aug 31, 2011
my hp 5102 takes long to start.
View 1 Replies
View Related
Aug 22, 2011
I did a speed test and everything seemed good. Dl speeds at 16mb/s and upload speeds at .99 mb/s. However when I go to websites and load pictures it takes like a minute to load. Why is that?y speed seems fine when I test it, but slow to load stuff.
View 1 Replies
View Related
Sep 10, 2011
How to fix our LMS 4.0 high CPU issues?. It takes lots of resources and also some time stop responding.
View 7 Replies
View Related
Apr 28, 2013
I am using Cisco AnyConnect VPN Client v2.3.0254 and ever since i upgraded my laptop from the Lenovo T420 to the Lenovo T430 the time it takes to connect via VPN has increased drastically. Connecting via VPN on my Lenovo T420 would take as little as 5 seconds to authenticate and connect while connecting with my T430 is now taking at minimum of 5 minutes, sometimes upwards of 15 minutes only to report back an error!
The screen the AnyConnect VPN Client seems to hang on is "Establishing VPN - Initiating Connection..."
The server is enforcing that McAffee is installed and up to date, however i have already made sure that my McAffee install is valid and up to date.
I have already taken these steps to try to correct the issue: Re installed Cisco AnyConnect VPN ClientRe installed & updated virus definitions for McAffeeRan CheckDisk on my primary OS partitionRan RAM validation utility to verify no bad sectors I have attached a screenshot of the error log from AnyConnect as well as the log html file.
View 2 Replies
View Related
Jan 4, 2011
I have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies
View Related
Jul 8, 2012
I just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies
View Related
Sep 19, 2012
Every time i boot up my laptop the little blue ring in the lower right corner just completely stops and it keeps me from opening anything and i have to wait at least 2 to 3 minutes to start up?
View 3 Replies
View Related
Dec 20, 2012
After startup, the computer takes about 15 seconds for it to identify the LAN.
View 1 Replies
View Related
Nov 26, 2012
I have notice that my XPS 17 L702x takes more than usual to boot than before.
View 5 Replies
View Related
Sep 10, 2012
How does Replication of cucm servers and other servers like unity presence and all in a cluster take place?
View 1 Replies
View Related
Jan 3, 2012
I am trying to setup a translation rule that takes any three numbers that start with a 4.. and translate it to 14.. I have tried a few ways of what I thought would work but nothing is working.
Examples of what I have tried:
rule 2 /(...)/ /1.../
rule 2 /4../ /1.../
rule 2 /4../ /11/
This is the rule that I use to delete the 1 when traffic flows out of my voip system.
rule 1 /^1(...$)/ /1/
View 2 Replies
View Related