I am trying to setup a translation rule that takes any three numbers that start with a 4.. and translate it to 14.. I have tried a few ways of what I thought would work but nothing is working.
Examples of what I have tried:
rule 2 /(...)/ /1.../
rule 2 /4../ /1.../
rule 2 /4../ /11/
This is the rule that I use to delete the 1 when traffic flows out of my voip system.
rule 1 /^1(...$)/ /1/
i am trying to find out if it is possible to have a translation rule fail over to a second server if the primary is down on my cisco pix515e.so for instance having an external ip address of 82.x.x.x mapped to an internal ip of 10.x.x.1
If 10.x.x.1 is down then 82.x.x.x should be mapped to 10.x.x.2.The reason i am asking this is i also have 2 css11501 load balancers and would like to have our staging servers primarily sat on one with secondary connectioin to second, production on the other failing over to each other if one is down. The load balancers will be connected to different ports on the same firewall.
I have a network with multiple voip gateways run by an Asterisk server. Among others, I'm using a Cisco 1760 with a VIC-BRI as ISDN gateway.To standardize the dial patterns between these different systems, I have decided to systematically translate them to e.164 before sending them from one system to the other.
View 3 Replies View Relatedaccounting in ACS 5.3. When I setup accounting on WLC 440x / 5508 ACS takes them as an authentication request and fail.
Here are some logs what I see in acsview:
Dec 9,11 6:05:11.783 PM
Radius authentication failed for USER: navrka2 MAC: a.b.c.d AUTHTYPE: Radius authentication failed
ACS Session ID:
dc2aaa1v/112555963/420
Audit Session ID:
0a9a01d7000001fd4ee23a3d
Tunnel Details:
[code]...
what is the purpose of the "Permint all traffic to less secure networks".
Well I know the purpose and the technique to handle some sercurity level is nice. when I cannot add add a rule without deleting this implicit rule?
The technique of security level is then obsolete?
I accidentally setup two schedule rules both with the name of "Log". When I highlight either rule, and try to delete either, I get error "The rule is being used by another rule and cannot be deleted" How do I delete?
View 1 Replies View RelatedI've had this dsl modem for a couple years now and have always to my knowledge been able to use it via only one ip number.i've been streaming video using webcamxp and other software/.today my modem began acting stupid by disconnecting once an hour and if I shut off pc of at all,i wind up having to manually reset the modem by unplugging it for a few seconds and then back in again.i eventually noticed that while the webcam is streaming video ,my lan connection on the pc shows the ip number i'm familiar with while my dsl modem shows one that's new(so to speak)..so I entered both ip numbers in to the webcamxp and found that the modem streams using either ip number..if I go to the what's my ipnumber site,it will display whichever number I have entered in to the webcamxp software//.is it normal for a modem to use 2 numbers as I don't believe this has occurred in my case before.i'm wondering if it has to do with the modem suddenly disconnecting now and then and too,having to reset it everytime I boot.i have att dsl ,no live landline just dead phone cord from the modem to the wall.
View 1 Replies View RelatedHow to get any numbers regarding performance for acs v.5 ? I have looked through the documents but couldnt really get any idea. Especially in a WLAN environment - how many clients can use one appliance as primary without putting the primary under strong load ?
View 1 Replies View RelatedI have a little experience in LAN management, solving basic connectivity issuesHowever, I am not strong theoretically. Particularly, when it comes to OSI reference model,I feel like I have understood the funda, but at the same time, I get lost, here and there,This is regarding the steps or processes involved, when one PC sends an email to another in a network,When I compose an email and hit enter, this is what I have understood.Each layer, starting from the application layer, passes the data and the control information to the layer below it, until the lowest layer is reached, from where, the actual transmission takes place via the physical medium.What are port numbers? How and when are port numbers chosen? Who takes the decision in choosing them?
View 2 Replies View RelatedI did the ISC 5.2 on Solaris restore successfully but when I want to start the DB by running STARTDB but it gives me this error.
View 0 Replies View RelatedI am in the process of implementing 750 Cisco Access Points acros the business. I need to make a note of the serial numbers and Mac addresses for our inventory before I get these configured and sent out to their relavent destinations. The AP's have have arrived in boxes of 10 (75 boxes). The sticker on the box with the barcode is either covered with a postage sticker, ripped, or my scanner will not scan it becaise it is too small. There is a sticker with the serial bundle which is larger and therefore scanable. Is there a way that I can scan this and get the MAC address and serial number.
I know that this is not a technical question but I don't want too spend the next 3 weeks opening 75 boxes and removing each AP individually and recording it.
I want to know, if it is possible to create multiples BGP AS Numbers on a ASR1K6 Router or ASR9K6 Router.
View 3 Replies View RelatedI have a monitoring rule that checks the number of connections on the firewall using the following command: show conn count
My results are always between 3,000 and 9,000.A while back, I had an issue where all 130,000 connections were being used up. I configured a service policy to limit the number of connections between any two end points.
I'm monitoring the error logs and I'm noticing that my connection limit rule is being triggered on a regular basis. I receive the following message.Per-client connection limit exceeded 20000/20000 for output packet from x.x.x.x to x.x.x.x on interface outside
I'm confused as to the difference between the connections limited by my rule and the connections shown by "show conn count". why I never see any connections higher than 9,000 using "show conn count" yet I am seeing alerts stating that the firewall has reached 20000 connections?My firewall is an ASA5510 running.
I would like to block IP numbers. When I tried with one the router festively walked straight through it!
View 6 Replies View RelatedI have installed LMS 3.2 on win 2003 server. It was working fine for last 1 year. Due to some requirement we restarted teh server, after which the LMS services did not came up. Now if we are giving the command "net start crmdmgdt", it give the following error message.The service is not responding to the control function.While checking the application log in event viewer we are getting the error message " Faulting application dmgtd.exe, version 1.0.0.1, faulting module msvcrt.dll, version 7.0.3790.3959, fault address 0x000385f2"
If we are restarting the server then also similar kind of error message is appearing" Reporting queued error: Faulting application dmgtd.exe, version 1.0.0.1, faulting module msvcrt.dll, version 7.0.3790.3959, fault address 0x000385f2".
Since last week, the login to CiscoWorks page comes up blank. The output of pdshow shows all the processes running except CTMJrmServer.
Process= CTMJrmServer
State = Administrator has shut down this server
Pid = 0
RC = 0
Signo = 0
Start = 01/26/12 18:08:11
[code]....
The CTMJrmServer is not starting and the log shows:
[ Thu Jan 26 18:08:14 GMT 2012 ],FATAL,[main],com.cisco.nm.rmeng.jrmwrapper.server.JobManagerExt,getJRM,242,ERROR: Could not establish connection with JRM.
These are production systems running LMS2.6 and the users are not able to login.
I was thinking, is there a way to view a report on the configured numbers within CUCM? E.g. not only extension numbers but hunt pilots and other things such as that? Rather than manually going to each page.
View 13 Replies View RelatedI have bought 2 new ASA5505 with SmartNet contract. I already have my 2 SmarNet contract number. Now I want to add these 2 contracts to my TAC account, so I can have support for my 2 new products. My TAC account already have 1 SmartNet contract for another device I have.What is the procedure to add my SmartNet contract to my account?
View 2 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 2 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 1 Replies View RelatedI have Any Connect (ver 3.1.01065) configured on Cisco router 891. VPN is working fine from the desktop, but I also need the ability to establish a VPN connection through a RDP connection (i.e. I'm using RDP to connect to a PC which has AnyConnect installed on, then trying to establish a VPN connection). OS Windows 7 SP1 x86.I've read about changing some settings in profile file (changed the <WindowsVPNEstablishment> option to "AllowRemoteUsers". Then applied the profile to the relevant Group Policy. Connected VPN from the PC (not through RDP), so that it downloads the new profile, and then disconnected again.): url...
But this make sense to the cisco asa... I have a cisco router on the ios 15.1. I've checked the XML file on the local PC to confirm the profile has been downloaded and is has, and I can't see the AllowRemoteUsers option.So I still can't start VPN through an RDP connection. (Error is "VPN establishment capability from a remote desktop is disabled. A VPN connection will not be established".)This also happened with the previous version of AnyConnect (2.5.xxxx).The PC's local routing tables look fine, and I can't see any conflicts that would cause the RDP session to drop.In the main window of Cisco anyconnect secure mobility client Ive noticed label: Web Authentication required.
My cisco asa ar configured as show:
Cisco asa <outside int ip 192.168.1.2/30>----------------FIBER---------------------<192.168.1.1/30>Service provider------>internet
1-The network addressing between my cisco asa and the service provider is an private non routable ip addressing ( 192.168.1.0/30)
2-My lan pool are patted to 212.198.4x.xx to join the internet
3-The ip address used for pat is nat assigned to any physical interface
4-How can i configure a site to site vpn using the public ip address used for the pat.
I've freshly installed LMS 4.0 on VM server 2003 R2, after entering login details I'm getting the error Internet Explorer cannot display the webpage
View 3 Replies View Relatedgot a crahed 5520 this week and was showing <163>Nov 28 2011 11:34:45: %ASA-3-201013: Per-client connection limit exceeded -125/100 What the negative number tells ? i usually see same numbers like 100/100 with means the connection limited has reached.
View 3 Replies View Relatedit's possible to retrieve Tengig interface serial numbers via CLI? We have a couple of them in 3750 switches, and we need them for our inventory.
View 1 Replies View Relatedjust ran a discovery on a large network and found 49 wireless controllers (5500, 4400 and 2000 series) and none of them are showing the controller serial number. They are all running 7.0.235.0 and I found no bugs that match this issue.
View 1 Replies View RelatedIs there a way to change interface numbers on a 3750 stack but, still retain the config of the physical port?
For instance:
I would like to take the top switch, which has the ports numbered g2/0/1 - 52 and change them to be g1/0/1 - 52. And the bottom switch, which has ports numbered g1/0/1 - 52 and change them to be g2/0/1 - 52. Basically, just swap the interface numbers but, not effect any interface configurations.
I have larger numbers of WS-C3560X-24/24P/48 Cisco switches with1000BaseSX SFP GIBCs installed per switch in my network and they are all added to my DCR just fine. However, when i generate an inventory hardware report GBICs and GBICs serial number is not showing up. Is there any special settings i need to make?
View 6 Replies View RelatedI had a problem with my laptop ICS.
1 Acer laptop with windows 7 home premium
1 MSI laptop with windows 7 ultimate
1 Hp Netbook with windows 7 starter
1 USB Broadband
First i had connect the USB Broadband using by acer laptop to make as wifi router/wifi host via ad hoc.MSI laptop and Hp Netbook was successfully connected and able to connected to the internet which share from Acer laptop.Second, after that i am trying to use MSI laptop to create as wifi router/wifi host just like the same way what i done with Acer laptop.My both Acer laptop and Hp Netbook successfully connect to MSI laptop but only the Acer laptop was unable to connect to internet and it was showing "No Internet access". and the "homegroup something it showing "Unidentified network" on the MSI laptop.I had tried to restart all the laptop and netbook to resetting it, unlucky it still unable to connecting to internet.Also i had set all to "Obtain an IP address automatically".And i found out that my laptop ICS on service didnt starting and on Firewall didnt have ICS on the list.When i try to click the start buttom it popping out this:"The Internet Connection Sharing (ICS) service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs"
i'm new in wireless and have delegated a task to setup a wireless connection between two buildings (it should be on the same IP subnet), app. 300m apart. How to perform this task, what Cisco AP to use, antennas. I do have a WLC these APs will be connecting to. Currently have few extra 1142i AP - not sure if this can be used for bridging.
View 4 Replies View RelatedI'm starting my configuration and i created a test environment side by side with my production. i just run startup config and connected my ad-test.com AD host to it. i can ping ad-test.com from console, ok. but it can't get internet from inside environment
here's the config..............................
: Saved
: Written by enable_15 at 07:56:40.638 UTC Mon Apr 15 2013
!
ASA Version 8.6(1)2
[Code].....
I've got a 3750 stack with a 3750-48p being switch 1 and a 3750-12s being switch 2 and switch 2 is the master. I would like to change the stack member numbers. I would like the 3750-12s to be switch 1 and the 3750-48p to be switch 2. I undertand I will have to reboot the stack for the change to take affect but here are my questions: How would this change affect the stack running-config ? will the switchport config follow the change ?
View 5 Replies View RelatedI've got a 3750 stack with a 3750-48p being switch 1 and a 3750-12s being switch 2 and switch 2 is the master. I would like to change the stack member numbers. I would like the 3750-12s to be switch 1 and the 3750-48p to be switch 2. I undertand I will have to reboot the stack for the change to take affect but here are my questions:
- How would this change affect the stack running-config ?
- will the switchport config follow the change ?
switch 1 provision ws-c3750-48p
switch 2 provision ws-c3750g-12s