I was thinking, is there a way to view a report on the configured numbers within CUCM? E.g. not only extension numbers but hunt pilots and other things such as that? Rather than manually going to each page.
View 13 Repliesbit of a newbie to this call manager stuff but I was having a bit of a play earlier and for the life of me I can not see an easy way to list which directory numbers are in a particular pickup group. I can see the list of pickup groups and how to assign the directory number to a pickup group but surely there's an easy way to find out which numbers are in a particular pickup group???
View 1 Replies View RelatedI am trying to run Audit reports for config change (Reports > Compliance and Audit > Change Audit > Standard). If I use "Immediate" Run Type a report gets generated with exactly what we need. If I try to use anything else so LMS can generate an email we keep getting this error. I had a look on the forum and supposedly this should be fixed since 3.2.
View 7 Replies View RelatedI am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
View 3 Replies View RelatedI am trying to setup 4 cameras to view with remote live view. I set up my server with IP addresses of 192.168.1.80 .... 85. The screen has only the option for 1 video channel. I have seen on-line screen shots that have options for channel 1 through 8. I want to assign each camera to a different channel so I will be able to use remote live view to show all 4 cameras at the same time. I can only show one at a time. Do I need a different version than 3.3 or some obscure windows 7 setting?
View 5 Replies View RelatedI want to Upgrade CUCM 8.0 to 8.6 version. What are the necessary steps, any tools, license requirements?
View 1 Replies View RelatedWe are upgrading from Callmanager 4.0(2a) to new hardware and the latest version. We have Callmanger 4.0(2a) and would like to upgrade to the newest version, at least to CUCM 8. We already have the new hardware that is compatible, smartnets and licenses. After looking at the matrix sheet it appears (there were several different upgrade routes but I could only find documentation for upgradring to 7.1(2) and 7.0(1) from 4.x so I am going with 7.1(2)) should we go:
from 4.0(2a) to 4.3(1)
from 4.3(1) to 7.1(2)
from 7.1(2) to 8.0(1)
this gets us to 8 which we can then upgrade to 8.5 or 8.6
So, we have 4 servers, 2 old (Pub, Sub) and 2 new (Pub, Sub). What is the best plan of attack here:
1) Backup 4.0(2a), then do an inplace upgrade on old hardware from 4.0(2a) to 4.3(1). Then backup 4.3(1) and do another inplace upgrade on the same server to 7.1(2). Then load 7.1(2) on the new hardware and restore backup from 7.1(2) on the old hardware. Then backup and inplace upgrade to 8.0 on the new server?
Or
2) is there any way to not have to "touch" or do an inplace upgrade on the old hardware running 4.0(2a), and just run a backup on it, load 8.5 on the new server and import the data over from the backup?
What vmware i have to use to install cucm 7. vmware workstation 7 or vmware server or exsi 4 or 5. Any correct link to download and vmware config settings.
View 2 Replies View Relatedthe customer has CUCM in the inventory database of LMS 4.1. He has all accesses from LMS to CUCM. One phone 7961 is seen in the UT report. When the customer click on the CUCM in the inventory - there is no IP phone registered in the CUCM.
View 2 Replies View Relatedthe customer has CUCM in the inventory database of LMS 4.1. He has all accesses from LMS to CUCM. One phone 7961 is seen in the UT report. When the customer click on the CUCM in the inventory - there is no IP phone registered in the CUCM. What is wrong?:-( See the attachment.
View 1 Replies View RelatedI've looked in many places but cannot see how or if it is possible to configure a phone, in CUCM to have a feature ring instead of the normal ring.In CUCME you go into the ephone x configuration mode, and assign the DN to the phone with the button xfx command. What this gives you is a slightly different ring tone when a call comes through. If I am not mistaken it is the same ringtone they use on the show "24".Is there a way to do this "feature" with CUCM?
View 1 Replies View RelatedI have a problem with my Cisco 7961 phones not registering on my CUCM 8.6 install on ESXi 5. Weird because I have Cisco IP communicator phones that register with no problem. You guys know what I can be missing. I have restarted the CUCM and services multiple times. The phone log on my phones say it can't find dhcp and DNS unknown host but my CUCM is configured by IP address. I also attached some screenshots
View 3 Replies View RelatedI have a CUOM 2.3 and CUCM 7.0 installed, we are planned to have a major upgrade to CUCM to 8.5 soon, do i need to upgrade my CUOM ,since CUOM is a Network management system? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license? Is OM 2.3 to 8.X is a direct upgrade?
View 3 Replies View RelatedMy Customer today have CUOM 2.3 and CUCM 7.1.3. He is planning to do upgrade CUOM 8.6 and CUCM 8.6. My question is: Is it possible to do upgrade CUOM directly to 8.6? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license?
View 4 Replies View RelatedLooks like I still have an issue with LMS to recognize the IP Phones in UT as IP Phones. SNMP RO on Call Manager is enabled and is green in CM (e.g. topology) - so SNMP get is basically fine. The Phones are recognised as End Devices in UT.
As far as I understand, now if I start a Phone Aquisition, the CUCM is polled by LMS to gather additional information about the phones. So it seems there is a problem with the SNMP polling of the Call manager?
How does Replication of cucm servers and other servers like unity presence and all in a cluster take place?
View 1 Replies View RelatedI am trying to configure my ASA 7.2(4) to inspect SCCP traffic from a CUCM v7.I have been advised that the ASA device needs to support the version of Skinny I am running.What version of Skinny does ASA 7.2(4) support? How can I find out what version my phones are using?
View 3 Replies View RelatedI have a 2951 which i want to integrate to the CUCM and wish to plug a Siemens ISDX into it which is the best card to use
NM-HDV2-1T1/E1 or WIC2-2MFT-T1/E1? its QSIG
I've had this dsl modem for a couple years now and have always to my knowledge been able to use it via only one ip number.i've been streaming video using webcamxp and other software/.today my modem began acting stupid by disconnecting once an hour and if I shut off pc of at all,i wind up having to manually reset the modem by unplugging it for a few seconds and then back in again.i eventually noticed that while the webcam is streaming video ,my lan connection on the pc shows the ip number i'm familiar with while my dsl modem shows one that's new(so to speak)..so I entered both ip numbers in to the webcamxp and found that the modem streams using either ip number..if I go to the what's my ipnumber site,it will display whichever number I have entered in to the webcamxp software//.is it normal for a modem to use 2 numbers as I don't believe this has occurred in my case before.i'm wondering if it has to do with the modem suddenly disconnecting now and then and too,having to reset it everytime I boot.i have att dsl ,no live landline just dead phone cord from the modem to the wall.
View 1 Replies View RelatedHow to get any numbers regarding performance for acs v.5 ? I have looked through the documents but couldnt really get any idea. Especially in a WLAN environment - how many clients can use one appliance as primary without putting the primary under strong load ?
View 1 Replies View RelatedIn CUCME if you do not configure any translation rules and leave the system mainly at default, when a call is routed to the PSTN the CUCME system sends the true calling party ID which would be a users extension number. Is it correct to assume that a CUCM server based system, when too left at the majority of default (without translation rules or stripping etc) that it will send the true calling ID to the gateway?
View 1 Replies View RelatedWe have CUCM & lync server setup and its working fine if any one calling each other with DNS load balancing. But customer want ot use Cisco ACE 4710 instead of DNS LB.We have configured Cisco LB and deploy but when CUCM user calling to lync user call going to disconnect after 4 sec and also Lync users unable to make call to CUCM.And also LB deploye between share point but when users are trying to open web session that time web page going to show page cannot display.
[code]....
I have a little experience in LAN management, solving basic connectivity issuesHowever, I am not strong theoretically. Particularly, when it comes to OSI reference model,I feel like I have understood the funda, but at the same time, I get lost, here and there,This is regarding the steps or processes involved, when one PC sends an email to another in a network,When I compose an email and hit enter, this is what I have understood.Each layer, starting from the application layer, passes the data and the control information to the layer below it, until the lowest layer is reached, from where, the actual transmission takes place via the physical medium.What are port numbers? How and when are port numbers chosen? Who takes the decision in choosing them?
View 2 Replies View RelatedI am in the process of implementing 750 Cisco Access Points acros the business. I need to make a note of the serial numbers and Mac addresses for our inventory before I get these configured and sent out to their relavent destinations. The AP's have have arrived in boxes of 10 (75 boxes). The sticker on the box with the barcode is either covered with a postage sticker, ripped, or my scanner will not scan it becaise it is too small. There is a sticker with the serial bundle which is larger and therefore scanable. Is there a way that I can scan this and get the MAC address and serial number.
I know that this is not a technical question but I don't want too spend the next 3 weeks opening 75 boxes and removing each AP individually and recording it.
I want to know, if it is possible to create multiples BGP AS Numbers on a ASR1K6 Router or ASR9K6 Router.
View 3 Replies View RelatedI have a monitoring rule that checks the number of connections on the firewall using the following command: show conn count
My results are always between 3,000 and 9,000.A while back, I had an issue where all 130,000 connections were being used up. I configured a service policy to limit the number of connections between any two end points.
I'm monitoring the error logs and I'm noticing that my connection limit rule is being triggered on a regular basis. I receive the following message.Per-client connection limit exceeded 20000/20000 for output packet from x.x.x.x to x.x.x.x on interface outside
I'm confused as to the difference between the connections limited by my rule and the connections shown by "show conn count". why I never see any connections higher than 9,000 using "show conn count" yet I am seeing alerts stating that the firewall has reached 20000 connections?My firewall is an ASA5510 running.
I would like to block IP numbers. When I tried with one the router festively walked straight through it!
View 6 Replies View RelatedI have bought 2 new ASA5505 with SmartNet contract. I already have my 2 SmarNet contract number. Now I want to add these 2 contracts to my TAC account, so I can have support for my 2 new products. My TAC account already have 1 SmartNet contract for another device I have.What is the procedure to add my SmartNet contract to my account?
View 2 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 2 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 1 Replies View RelatedI am trying to setup a translation rule that takes any three numbers that start with a 4.. and translate it to 14.. I have tried a few ways of what I thought would work but nothing is working.
Examples of what I have tried:
rule 2 /(...)/ /1.../
rule 2 /4../ /1.../
rule 2 /4../ /11/
This is the rule that I use to delete the 1 when traffic flows out of my voip system.
rule 1 /^1(...$)/ /1/
got a crahed 5520 this week and was showing <163>Nov 28 2011 11:34:45: %ASA-3-201013: Per-client connection limit exceeded -125/100 What the negative number tells ? i usually see same numbers like 100/100 with means the connection limited has reached.
View 3 Replies View Relatedit's possible to retrieve Tengig interface serial numbers via CLI? We have a couple of them in 3750 switches, and we need them for our inventory.
View 1 Replies View Related