I've had this dsl modem for a couple years now and have always to my knowledge been able to use it via only one ip number.i've been streaming video using webcamxp and other software/.today my modem began acting stupid by disconnecting once an hour and if I shut off pc of at all,i wind up having to manually reset the modem by unplugging it for a few seconds and then back in again.i eventually noticed that while the webcam is streaming video ,my lan connection on the pc shows the ip number i'm familiar with while my dsl modem shows one that's new(so to speak)..so I entered both ip numbers in to the webcamxp and found that the modem streams using either ip number..if I go to the what's my ipnumber site,it will display whichever number I have entered in to the webcamxp software//.is it normal for a modem to use 2 numbers as I don't believe this has occurred in my case before.i'm wondering if it has to do with the modem suddenly disconnecting now and then and too,having to reset it everytime I boot.i have att dsl ,no live landline just dead phone cord from the modem to the wall.
I have a little experience in LAN management, solving basic connectivity issuesHowever, I am not strong theoretically. Particularly, when it comes to OSI reference model,I feel like I have understood the funda, but at the same time, I get lost, here and there,This is regarding the steps or processes involved, when one PC sends an email to another in a network,When I compose an email and hit enter, this is what I have understood.Each layer, starting from the application layer, passes the data and the control information to the layer below it, until the lowest layer is reached, from where, the actual transmission takes place via the physical medium.What are port numbers? How and when are port numbers chosen? Who takes the decision in choosing them?
How to get any numbers regarding performance for acs v.5 ? I have looked through the documents but couldnt really get any idea. Especially in a WLAN environment - how many clients can use one appliance as primary without putting the primary under strong load ?
I am in the process of implementing 750 Cisco Access Points acros the business. I need to make a note of the serial numbers and Mac addresses for our inventory before I get these configured and sent out to their relavent destinations. The AP's have have arrived in boxes of 10 (75 boxes). The sticker on the box with the barcode is either covered with a postage sticker, ripped, or my scanner will not scan it becaise it is too small. There is a sticker with the serial bundle which is larger and therefore scanable. Is there a way that I can scan this and get the MAC address and serial number.
I know that this is not a technical question but I don't want too spend the next 3 weeks opening 75 boxes and removing each AP individually and recording it.
I have a monitoring rule that checks the number of connections on the firewall using the following command: show conn count
My results are always between 3,000 and 9,000.A while back, I had an issue where all 130,000 connections were being used up. I configured a service policy to limit the number of connections between any two end points.
I'm monitoring the error logs and I'm noticing that my connection limit rule is being triggered on a regular basis. I receive the following message.Per-client connection limit exceeded 20000/20000 for output packet from x.x.x.x to x.x.x.x on interface outside
I'm confused as to the difference between the connections limited by my rule and the connections shown by "show conn count". why I never see any connections higher than 9,000 using "show conn count" yet I am seeing alerts stating that the firewall has reached 20000 connections?My firewall is an ASA5510 running.
I was thinking, is there a way to view a report on the configured numbers within CUCM? E.g. not only extension numbers but hunt pilots and other things such as that? Rather than manually going to each page.
I have bought 2 new ASA5505 with SmartNet contract. I already have my 2 SmarNet contract number. Now I want to add these 2 contracts to my TAC account, so I can have support for my 2 new products. My TAC account already have 1 SmartNet contract for another device I have.What is the procedure to add my SmartNet contract to my account?
I have AT&T Uverse and VOIP. I can receive calls but when I try to call out many local numbers and 800 #'s I get a busy signal. I called AT&T and they said everything looks ok to them. Could this have anything to do with Windows firewall or modem settings?
I am trying to setup a translation rule that takes any three numbers that start with a 4.. and translate it to 14.. I have tried a few ways of what I thought would work but nothing is working.
How to get this unit to hand out the Ip numbers in my network with dhcp but to allso assign these numbers in accordance to the mac address. I want o make sure the same computers get the same internal ip and not random ones?
got a crahed 5520 this week and was showing <163>Nov 28 2011 11:34:45: %ASA-3-201013: Per-client connection limit exceeded -125/100 What the negative number tells ? i usually see same numbers like 100/100 with means the connection limited has reached.
just ran a discovery on a large network and found 49 wireless controllers (5500, 4400 and 2000 series) and none of them are showing the controller serial number. They are all running 7.0.235.0 and I found no bugs that match this issue.
Is there a way to change interface numbers on a 3750 stack but, still retain the config of the physical port?
For instance:
I would like to take the top switch, which has the ports numbered g2/0/1 - 52 and change them to be g1/0/1 - 52. And the bottom switch, which has ports numbered g1/0/1 - 52 and change them to be g2/0/1 - 52. Basically, just swap the interface numbers but, not effect any interface configurations.
I have larger numbers of WS-C3560X-24/24P/48 Cisco switches with1000BaseSX SFP GIBCs installed per switch in my network and they are all added to my DCR just fine. However, when i generate an inventory hardware report GBICs and GBICs serial number is not showing up. Is there any special settings i need to make?
I've got a 3750 stack with a 3750-48p being switch 1 and a 3750-12s being switch 2 and switch 2 is the master. I would like to change the stack member numbers. I would like the 3750-12s to be switch 1 and the 3750-48p to be switch 2. I undertand I will have to reboot the stack for the change to take affect but here are my questions: How would this change affect the stack running-config ? will the switchport config follow the change ?
I've got a 3750 stack with a 3750-48p being switch 1 and a 3750-12s being switch 2 and switch 2 is the master. I would like to change the stack member numbers. I would like the 3750-12s to be switch 1 and the 3750-48p to be switch 2. I undertand I will have to reboot the stack for the change to take affect but here are my questions:
- How would this change affect the stack running-config ?
I run a website for a local football team using Serif Webplus X6. On uploading the weekly updates of the site the process seems ok for a few minutes with progress bars showing uploading of files but then it all stops and I have to reset my wireless network adaptor 1703 and it continues but I can't just leave it to work on its own. Device manager says that the drivers are up to date but I'm fed up with having to nurse the adaptor. This didn't happen with previous computers.
I have a remote site that is using port 4500 for within the isakmp phase of creating a IPSEC tunnel, but for some reason it is also using random port numbers constantly (in bold): [code] These are all blocked by the firewall when trying to communicate with our central router in the trusted network. The central router does not display the same symptoms, it only uses port 4500.Is there a way of preventing the remote router from using random port numbers and only allowed to use 4500??
I have a 3750 as core switch, adding 2 stacks of 2960S to connect. I want to establish etherchannel between the 3750 and each additonal 2960S stack, do the channel group numbers between the 3750 and the new 2960s have to match? 3750 has two channel-groups(1 and 2) already configured. Need to know, I would create 2 additional channel groups (number 3,4) for each of the etherchannels between the 3 2960S Stacks and 3750? OR channel-group # is local to the device.
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
I want to connect my tata photon device to my bsnl wifi modem via a usb portavailable on the bsnl modem. This is to provide a wifi network that i can use to surf the net on my phone.
i just bought a Netgear WNDR4000 router due to troubles with my current modem/router combo (D-Link DSL2730-B). The router doesnt have in built modem functionality obviously so I need to set up the modem/router as a dedicated modem.Also should I use the current modem/router as the dedicated modem or an older model i own (I think its a DSL 502T)? Because the current one often drops the internet connection. Don't know if its a problem with the modem functionality or something else. Will the older one serve better since i didn't have any problems with that one or will it be outdated? I only upgraded due it not having wireless capabilities. Otherwise it's fine.Or will I be even better off buying a dedicated modem? I really don't want to spend more money but if this is a far better alternative I guess i will.
EDIT: Ok so found out that I have to put the modem/router in bridge mode in order for this to be possible. However, looking up how to do this lead me to a dead end because i need to fill in some fields that i have no idea how to interpret.
VPI: VCI: These 2 already came with presets. Should I just leave them? Select DSL Link Type (EoA is for PPPoE, IPoE, and Bridge): Choices of EoA PPPoA and IPoA Encapsulation Mode: Choices of LLC/SNAP-BRIDGING and VC/MUX Service Category: UBR without PCR, UBR with PCR, CBR, Non Realtime VBR, Realtime VBR
I have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
my computer randomly disconnects from my modem and will not reconnect until I restart my computer (do not need to restart modem). When I check the modem, it always is still running. The lights on the modem do the exact same thing whether the internet is working or not. The disconnection is entirely random. Sometimes it will disconnect immediately, sometimes it will take up to a few hours. I do not have a router hooked up to the modem, and the only other thing the modem is hooked up to is our tv. But even when the tv box is off, we still randomly disconnect.
On the previous forum thread that I read, some of the comments asked for the person to paste their entire ipconfig and their entire ping list from command prompt I will post that below: [code] Could it possibly be a virus? I am currently performing a virus scan using Microsoft Security Essentials. I will report the results of that tomorrow, seeing that it will take several (up to 10) hours to finish and it is nearly midnight of me posting this.I should also note that whenever I unplug my Ethernet cord it gives me a symbol that looks like this other than the regular disconnect with the red "X" over the wire symbol.
I'm switching to cable internet service instead of DSL. My Netgear router will not work with my cable modem; but it works like a charm with my DSL modem. Is it a problem with the router setup? Good thing I still have the DSL service.
I have Desktop and Laptop connected to a Huawei-make,Model No Smart AX 882, ,via ethernet & USB port. Is it possible to convert the same ADSL wired modem into a wireless modem for my Laptop. the type of hardware to be used (e.g., wireless access point or a wireless router) through my USB port in the wired modem? what is the configuration change I have do in my wired broad band modem?
i have a at&t modem and wireless router in one. its the source of my internet and is in my office room and i was wondering if i can use my old westell wireless modem router and hook it up in my bedroom so i can have a better signal for my laptop and use an ethernet cable for other things like the tv and ect
