I have larger numbers of WS-C3560X-24/24P/48 Cisco switches with1000BaseSX SFP GIBCs installed per switch in my network and they are all added to my DCR just fine. However, when i generate an inventory hardware report GBICs and GBICs serial number is not showing up. Is there any special settings i need to make?
View 6 RepliesAfter I upgrading all device packages, inventory collection failure to complete. All devices stuck on pending state and at the end of the job all devices are under not attempted and job result description ses " Timed out. Make shure that ICServer is running". I made sure that ICServer is running.
LMS runs on windows 2008 R2 server
I have Cisco Works LMS 4.0 on Win 2K8 64 bits on VMware EXs. I am facing issue with reference to Inventory Collection, my 10% devices (including Routers & Switches) Inventory collection is failed and give me error (Device sensed, but collection failed). I increase the SNMP timeout 10 sec, 30 sec, 60 sec and even 100 sec the result be the same.
View 1 Replies View RelatedA customer of mine have 2 VSS systems for wich IC times out during collection when trying to read from flash on them. From the ICserver.log
[ Thu Dec 13 16:45:19 CET 2012 ],WARN ,[Thread-20],com.cisco.nm.rmeng.util.logger.XDILogger,67,com.cisco.nm.xms.xdi.pkgs.SharedInventoryCatIOS.FlashAGI_CISCO_FLASH_Mib,g$eval,70,com.cisco.nm.xms.xdi.pkgs.S
[Code].....
LMS 4.0.1 installed on Windows Server 2008 R2 Standard with SP1. Created Inventory collection job, but couple of hours later, it is failed with all devices Not Attempted. Increased SNMP timeout on 10 sec, started again for only 1 device - collection failed again. I am attaching pdshow and ICServer file.
View 6 Replies View RelatedWe have LMS4.0 monitoring 100+ devices. In that collection we have 2 4506e switches. The switches are identical,but one is inventoried successfully and the other always fails.Both have verified their credentials. The 4506e failing inventory is the only device not being inventoried.I looked at other post and increased snmp timeout with no effect.
View 1 Replies View RelatedI was trying to add a 2504 to PI, but I keep coming up with this error in Unknown Devices: Collection Status : Unexpected error. [code]
View 4 Replies View RelatedI reinstalled CiscoWorks LMS (Windows 2008 R2) updated th LMS with all availible devicepackages and imported all devices with a xml bulk import of the former installation. Now I am frustrated.... because after the reinstallation LMS has problems collecting the inventory data.The inventory collection for one local device (Cisco WS-C3560-8PC-S) starts and nevers stops.... I have to stop the ICserver to stop the inventory collection.
I have only 4 of nearly 1800 devices where it was possible to collect the inventory information.All the rest is supposed to unreacheable...Reports> Inventory>Management Status>Unreachable Devices.But if I take one of the devices which is reported to be unreacheable and do a device diagnostic (Monitor> Troubleshooting Tools> Troubleshooting Workflows) says it is reacheable...
The inventory does not appear in the "Collector Status"?
On our CiscoWorks 2000 installation, running on Solaris with LMS3.2 and RME4.3.1, we noticed a few weeks ago, that the job "Inventory Collection" needs more and more time to finish. At the moment the job execution time is as high as 8 hours, compared to 3 hours before. When we look at the network traffic during job execution, we see after the collection phase (~3h) several hours with no traffic together with a very high CPU load. I mean to remember that this job used to complete around 15 minutes after data collection phase. Restarting the application and rebooting the system didn't work.When we look in to the IC_Server.log, we find devices with a completion time of over 20'000 seconds. Increasing from day to day. [code]
Affected devices are Cisco Nexus 5548P. We tried to delete/add these devices. That works for a few days, then the runtime starts to increase again.
Are we hitting a bug? And is it possible, as a workaround, to exclude devices from only the Inventory Collection?
When I do an Inventory Collection, the job doesn´t work with some devices and I have to restart the server. The job doesn´t fail but the log ICServer.log doesn´t got any information and it works for hours and hours and when it finally stops I can see that devices are not attempted.
I have done some succesfull Inventory Collections with Cisco 3750 switches and 805 routes. I have tried witch Cisco 2811 routers and 2950 and 2960 switches but it doesn´t work.
I have tried to update my LMS4.0.1 but it doesn´t find any actualization. However, in the Cisco download page there are some patches.
I'm currently experiencing some problems with LMS 3.1 where inventory collection fails on cat6500 switches running 12.2(33)SXI1, Sup720.
I have changed the SNMP timeout to 30 seconds.
we have the following problems with lms 3.2 on windows. Archive management and inventory collection fail.
The following messages we get:
DCMA0055: URN_NOT_FOUND : urn "JRM" : Not found !!
DCMA0077: Could not create job. Check dcmaclient.log for more details.
Someone recommend to remove the following files ctmregistry and ctmregistry.backup.Will this fix the issue?
I have 3560-24PS-S (ios version 12.2(35)SE1) that have high CPU (almost 100%) use at every inventory collection (each sunday) or polling (each day 6 a.m) during 2 or 3 minutes.
I read on the forum, that this could be due to some mib object polling failure, and could, perhaps, be solved by upgrading the ios version or configuring view preventing the poll of the problematic object.
But what view to configure ?Is there well known MIB objects to filter ? Which ones ? I did not see any bug related to my IOS version and this behavior in the bug toolkit ... I join some sh commands (unfortunately done when no problem). I will try to obtain the output of the sh command when the pb occurs.
2 Nexus 5020 (SysObjId 3.719) brings internal error in inventory collection as following:"RICS0001: Internal Error, unable to process the collected data from the device".whereby 2 other devices from same type, same sysobjid are working well. SDT from v401 shows this device as supported.
View 10 Replies View RelatedI am in the process of implementing 750 Cisco Access Points acros the business. I need to make a note of the serial numbers and Mac addresses for our inventory before I get these configured and sent out to their relavent destinations. The AP's have have arrived in boxes of 10 (75 boxes). The sticker on the box with the barcode is either covered with a postage sticker, ripped, or my scanner will not scan it becaise it is too small. There is a sticker with the serial bundle which is larger and therefore scanable. Is there a way that I can scan this and get the MAC address and serial number.
I know that this is not a technical question but I don't want too spend the next 3 weeks opening 75 boxes and removing each AP individually and recording it.
it's possible to retrieve Tengig interface serial numbers via CLI? We have a couple of them in 3750 switches, and we need them for our inventory.
View 1 Replies View Relatedjust ran a discovery on a large network and found 49 wireless controllers (5500, 4400 and 2000 series) and none of them are showing the controller serial number. They are all running 7.0.235.0 and I found no bugs that match this issue.
View 1 Replies View RelatedI am trying to come up with an inventory report of all our 3750v2 stack switches, but for some reason I could not get the serial number of the member switch under each stack. Can Ciscowork LMS 3.2 see the serial number for each switch under a stack?
View 2 Replies View RelatedWe have a Cisco switch in each office and every now and then the port that has the D-Link Wireless AP (DAP-1522) connected to it goes to err-disable state. Actually sometimes even a regular port that has a cisco phone connected may also go to err-disable state (less often). So I have to telnet into the switch and issue shut and no shut command on that interface to get it back to life, then it works for a few days or weeks until it happens again. Any suitable configuraiton for that interface, that would prevent that from happening or a workaround ?
Here's the info:
Model: cisco WS-C3560-24PS and cisco WS-C3560-48PS
Image:c3560-ipbase-mz.122-35.SE5.bin
This is the log from one switch:
31w5d: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/2, putting Fa0/2 in err-disable state
31w5d: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 74e2.f592.f7f2 on port FastEthernet0/2.
31w5d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
And from another, which is almost the same:
5d10h: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/3, putting Fa0/3 in err-disable state
5d10h: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address d8a2.5e31.2cf6 on port FastEthernet0/3.
5d10h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down
5d10h: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Here's the configuration of fe interfaces (they are all alike):
interface FastEthernet0/2
description Voice & Data Combo Port
switchport access vlan 11
switchport mode access
switchport voice vlan 15
[code]....
I have came across some third-party ws-g5483's that I was thinking of using. But when I go to plug them in, nothing seems to happen. I have tried them in ws-c3548-xl-en and also a ws-c3524-pwr-xl-en with the same results. I know on the newer switches you can do the serviice unsupported-transceiver command but is there anything I can do to get these to work with older switches?
View 5 Replies View RelatedWhat type of Mini-GBICS should I used for RJ45 ethernet connections for my 4402 Wireles Lan Controller? Should I use the GLC-T SFP? Is it the right one? aAso is Mini-Gbics a industry standard which means I can use any brand of Mini-GBIC for this Connection like Dell Brand Dlink or Others.
View 1 Replies View RelatedI've had this dsl modem for a couple years now and have always to my knowledge been able to use it via only one ip number.i've been streaming video using webcamxp and other software/.today my modem began acting stupid by disconnecting once an hour and if I shut off pc of at all,i wind up having to manually reset the modem by unplugging it for a few seconds and then back in again.i eventually noticed that while the webcam is streaming video ,my lan connection on the pc shows the ip number i'm familiar with while my dsl modem shows one that's new(so to speak)..so I entered both ip numbers in to the webcamxp and found that the modem streams using either ip number..if I go to the what's my ipnumber site,it will display whichever number I have entered in to the webcamxp software//.is it normal for a modem to use 2 numbers as I don't believe this has occurred in my case before.i'm wondering if it has to do with the modem suddenly disconnecting now and then and too,having to reset it everytime I boot.i have att dsl ,no live landline just dead phone cord from the modem to the wall.
View 1 Replies View RelatedHow to get any numbers regarding performance for acs v.5 ? I have looked through the documents but couldnt really get any idea. Especially in a WLAN environment - how many clients can use one appliance as primary without putting the primary under strong load ?
View 1 Replies View RelatedI have a little experience in LAN management, solving basic connectivity issuesHowever, I am not strong theoretically. Particularly, when it comes to OSI reference model,I feel like I have understood the funda, but at the same time, I get lost, here and there,This is regarding the steps or processes involved, when one PC sends an email to another in a network,When I compose an email and hit enter, this is what I have understood.Each layer, starting from the application layer, passes the data and the control information to the layer below it, until the lowest layer is reached, from where, the actual transmission takes place via the physical medium.What are port numbers? How and when are port numbers chosen? Who takes the decision in choosing them?
View 2 Replies View RelatedI want to know, if it is possible to create multiples BGP AS Numbers on a ASR1K6 Router or ASR9K6 Router.
View 3 Replies View RelatedI have a monitoring rule that checks the number of connections on the firewall using the following command: show conn count
My results are always between 3,000 and 9,000.A while back, I had an issue where all 130,000 connections were being used up. I configured a service policy to limit the number of connections between any two end points.
I'm monitoring the error logs and I'm noticing that my connection limit rule is being triggered on a regular basis. I receive the following message.Per-client connection limit exceeded 20000/20000 for output packet from x.x.x.x to x.x.x.x on interface outside
I'm confused as to the difference between the connections limited by my rule and the connections shown by "show conn count". why I never see any connections higher than 9,000 using "show conn count" yet I am seeing alerts stating that the firewall has reached 20000 connections?My firewall is an ASA5510 running.
I would like to block IP numbers. When I tried with one the router festively walked straight through it!
View 6 Replies View RelatedAfter launching config collection job in LMS 4.2 I can't get job results and receive error message - Unable to get results of job execution for device. I've increased the job result wait time using option in Admin > Collection Settings ... , but nothing changed.Here are screenshots of error message and wait settings I used.
View 3 Replies View RelatedI was thinking, is there a way to view a report on the configured numbers within CUCM? E.g. not only extension numbers but hunt pilots and other things such as that? Rather than manually going to each page.
View 13 Replies View RelatedI have bought 2 new ASA5505 with SmartNet contract. I already have my 2 SmarNet contract number. Now I want to add these 2 contracts to my TAC account, so I can have support for my 2 new products. My TAC account already have 1 SmartNet contract for another device I have.What is the procedure to add my SmartNet contract to my account?
View 2 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 2 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 1 Replies View RelatedOur customer is try to make a configuration by web interface menu:
Admin > Collection Settings > Inventory
After select the menu below they always received this message:
Error in starting acquisition: unable to connect to server