We have LMS4.0 monitoring 100+ devices. In that collection we have 2 4506e switches. The switches are identical,but one is inventoried successfully and the other always fails.Both have verified their credentials. The 4506e failing inventory is the only device not being inventoried.I looked at other post and increased snmp timeout with no effect.
View 1 Replies
I'm currently experiencing some problems with LMS 3.1 where inventory collection fails on cat6500 switches running 12.2(33)SXI1, Sup720.
I have changed the SNMP timeout to 30 seconds.
After I upgrading all device packages, inventory collection failure to complete. All devices stuck on pending state and at the end of the job all devices are under not attempted and job result description ses " Timed out. Make shure that ICServer is running". I made sure that ICServer is running.
LMS runs on windows 2008 R2 server
I have Cisco Works LMS 4.0 on Win 2K8 64 bits on VMware EXs. I am facing issue with reference to Inventory Collection, my 10% devices (including Routers & Switches) Inventory collection is failed and give me error (Device sensed, but collection failed). I increase the SNMP timeout 10 sec, 30 sec, 60 sec and even 100 sec the result be the same.
View 1 Replies View RelatedA customer of mine have 2 VSS systems for wich IC times out during collection when trying to read from flash on them. From the ICserver.log
[ Thu Dec 13 16:45:19 CET 2012 ],WARN ,[Thread-20],com.cisco.nm.rmeng.util.logger.XDILogger,67,com.cisco.nm.xms.xdi.pkgs.SharedInventoryCatIOS.FlashAGI_CISCO_FLASH_Mib,g$eval,70,com.cisco.nm.xms.xdi.pkgs.S
[Code].....
LMS 4.0.1 installed on Windows Server 2008 R2 Standard with SP1. Created Inventory collection job, but couple of hours later, it is failed with all devices Not Attempted. Increased SNMP timeout on 10 sec, started again for only 1 device - collection failed again. I am attaching pdshow and ICServer file.
View 6 Replies View RelatedI was trying to add a 2504 to PI, but I keep coming up with this error in Unknown Devices: Collection Status : Unexpected error. [code]
View 4 Replies View RelatedI reinstalled CiscoWorks LMS (Windows 2008 R2) updated th LMS with all availible devicepackages and imported all devices with a xml bulk import of the former installation. Now I am frustrated.... because after the reinstallation LMS has problems collecting the inventory data.The inventory collection for one local device (Cisco WS-C3560-8PC-S) starts and nevers stops.... I have to stop the ICserver to stop the inventory collection.
I have only 4 of nearly 1800 devices where it was possible to collect the inventory information.All the rest is supposed to unreacheable...Reports> Inventory>Management Status>Unreachable Devices.But if I take one of the devices which is reported to be unreacheable and do a device diagnostic (Monitor> Troubleshooting Tools> Troubleshooting Workflows) says it is reacheable...
The inventory does not appear in the "Collector Status"?
On our CiscoWorks 2000 installation, running on Solaris with LMS3.2 and RME4.3.1, we noticed a few weeks ago, that the job "Inventory Collection" needs more and more time to finish. At the moment the job execution time is as high as 8 hours, compared to 3 hours before. When we look at the network traffic during job execution, we see after the collection phase (~3h) several hours with no traffic together with a very high CPU load. I mean to remember that this job used to complete around 15 minutes after data collection phase. Restarting the application and rebooting the system didn't work.When we look in to the IC_Server.log, we find devices with a completion time of over 20'000 seconds. Increasing from day to day. [code]
Affected devices are Cisco Nexus 5548P. We tried to delete/add these devices. That works for a few days, then the runtime starts to increase again.
Are we hitting a bug? And is it possible, as a workaround, to exclude devices from only the Inventory Collection?
When I do an Inventory Collection, the job doesn´t work with some devices and I have to restart the server. The job doesn´t fail but the log ICServer.log doesn´t got any information and it works for hours and hours and when it finally stops I can see that devices are not attempted.
I have done some succesfull Inventory Collections with Cisco 3750 switches and 805 routes. I have tried witch Cisco 2811 routers and 2950 and 2960 switches but it doesn´t work.
I have tried to update my LMS4.0.1 but it doesn´t find any actualization. However, in the Cisco download page there are some patches.
we have the following problems with lms 3.2 on windows. Archive management and inventory collection fail.
The following messages we get:
DCMA0055: URN_NOT_FOUND : urn "JRM" : Not found !!
DCMA0077: Could not create job. Check dcmaclient.log for more details.
Someone recommend to remove the following files ctmregistry and ctmregistry.backup.Will this fix the issue?
I have 3560-24PS-S (ios version 12.2(35)SE1) that have high CPU (almost 100%) use at every inventory collection (each sunday) or polling (each day 6 a.m) during 2 or 3 minutes.
I read on the forum, that this could be due to some mib object polling failure, and could, perhaps, be solved by upgrading the ios version or configuring view preventing the poll of the problematic object.
But what view to configure ?Is there well known MIB objects to filter ? Which ones ? I did not see any bug related to my IOS version and this behavior in the bug toolkit ... I join some sh commands (unfortunately done when no problem). I will try to obtain the output of the sh command when the pb occurs.
2 Nexus 5020 (SysObjId 3.719) brings internal error in inventory collection as following:"RICS0001: Internal Error, unable to process the collected data from the device".whereby 2 other devices from same type, same sysobjid are working well. SDT from v401 shows this device as supported.
View 10 Replies View RelatedI have larger numbers of WS-C3560X-24/24P/48 Cisco switches with1000BaseSX SFP GIBCs installed per switch in my network and they are all added to my DCR just fine. However, when i generate an inventory hardware report GBICs and GBICs serial number is not showing up. Is there any special settings i need to make?
View 6 Replies View RelatedI have an LMS 4.0.1 server (on Windows 2008 R2) with all the LMS and device updates applied that fails when trying to do an Inventory Collection on a Cisco 3925E router. The router is running IOS Version 15.1(1)T2. This device is apparently supported according to:
[URL]
Some 'show ver' info:
Cisco IOS Software, C3900e Software (C3900e-UNIVERSALK9-M), Version 15.1(1)T2, RELEASE SOFTWARE (fc1)
ROM: System Bootstrap, Version 15.1(1r)T2, RELEASE SOFTWARE (fc1)
System image file is "flash0:c3900e-universalk9-mz.SPA.151-1.T2.bin"
Cisco CISCO3925-CHASSIS (revision 1.0) with C3900-SPE200/K9 with 689152K/293888K bytes of memory.
'show inv':
NAME: "CISCO3925-CHASSIS", DESCR: "CISCO3925-CHASSIS"
PID: CISCO3925-CHASSIS , VID: V02, SN: FGL152610R8
[Code]....
You all know the senario; A managed device, let's say a c2801 router is being replaced with newer platform, let's say a c3900e series router. Might aswell be a C2960 being replace by a c3750x
I the goodolddays, with LMS3.2.1, you would get the "conflicting device" notice that the SNMP OID has changed on this managed device. you then need to press update and the device would then be managed once more.
How is tyhis done in LMS 4.2.2 ?
I seem to see more and more device in one of my installation, that DCR sees teh new OID and updates, but Inventory fails ... I get more of this, and the error is just; Internalt error in the job-browser .
I see Device Center info is wrong, but DCR info is right ..
What to do, and how do LMS handle this ? Can I get notice around when a device has been changed ?
I'm trying to set up a new switch, a 4506e, for a remote site. Most of our newer remote sites are using a 4506 and this is the first time I'm working with a 4506e. Our standard configuration, which was in use before I started here, has QoS settings. I'm not that familiar with QoS. Most of the QoS commands in our standard config aren't working in the 4506e. Does the 4506e have QoS? Is there some guide as to setting it up? Below are excerpts from the config we're using that are QoS related:
qos dblqos map dscp 32 33 34 35 36 37 38 39 to tx-queue 2qos map cos 3 to dscp 26 qos map cos 5 to dscp 46 qos aggregate-policer XYZ_AGG 64 mbps 8 mbyte conform-action transmit exceed-action drop qos!class-map match-all match_XYZ match access-group 142!policy-map police_XYZ class match_XYZ police aggregate XYZ_AGG!interface GigabitEthernet4/1 description server qos dscp 48!interface GigabitEthernet4/30 description server service-policy input police_XYZ!interface GigabitEthernet4/48 description upstream connection qos trust dscp tx-queue 1 shape 98 mbps tx-queue 2 shape 1 mbps tx-queue 3 priority high
Cisco 4506-E port configuration
WESTERN-4506-01#show int g4/47
GigabitEthernet4/47 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet Port, address is 0022.554c.01fe (
fe)
Description: Trunk to 425
[code]....
Cisco 3750 Configuration
interface FastEthernet1/0/1description 425Linkswitchport trunk encapsulation dot1qswitchport trunk native vlan 30switchport trunk allowed vlan 30,35switchport mode trunkswitchport nonegotiateswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitystorm-control broadcast level pps 300storm-control multicast level pps 300storm-control action trapmacro description cisco-desktopmac access-group AuthorizedHosts in
I have mac address' populated. I can see the device in layout on CNA with the proper name however cannot ping it.
4506 is 10.30.30.1
3750 is 10.30.30.2
Two days back my entire network was behaving in unusual ways.When is connect to core switc(4506e) through console. [code]
View 11 Replies View RelatedI have 4506e core switch to which 10 other 2960 switches are connected.I want to upgrade thier IOS. how can upgrade it, can I upgrade it one by one or all at a time?
Is there any tool to perform this task?
I started having connectivity issues between my core 4506E (Sup7E) and Cisco 2960S. There were input and CRC errors on Te int (SFP 10Gb - LRM) on 2960S, which cause the interface to reset and drop connections. While troubleshooting this issue, I have replaced patch cords and also had the tech checking the fiber. He said that there was some residue on one of the connectors, so the light levels fluctuated in 1300nm, but worked fine in 850. Well LRMs are using 1300, so he re-polished the tips, which worked to stabilize the light levels. After all that, I was still receiving the input/CRC errors, but the connection was NOT dropping. As my last resort I swapped the SFPs between the core and 2960, thinking I should start having issues on the core end. Well, here's what happened: I stopped receiving input/CRC errors on 2960 (also no errors on the core), but 2960s started generating Rx power high alarms: [code]
View 1 Replies View RelatedI would like to check if it may be possible to hot-upgrade/swap the 4506E power supplies? Based on the configuration guide; I have summarized the steps as follows:
1. Switch has 2 existing power supplies to be upgraded
2. Remove right side/bay 2 power supply and install new power supply
3. At this point; the new power supply will be in err-disabled due to different power supplies on the switch
4. Remove the left side power supply and install new power supply
For item 4; during the removal of the old power supply in bay 1/left side and installation of the new power supply; I am wondering if the switch would lose power even though the new power supply is installed in bay 2?
I have two cisco 4506-E series switches ..
We are planning to go for HSRP redundancy for 32 VLANs. Means In a Cisco 4506-E switch , we will configure 32 vlans and among them 16 vlans will be primary and 16VLANs will be standby ans it is viceversa in another core-switch
My querie is How many standby groups can we create in Cisco 4506-E switch,
Is there any limitation..
If there is any limitation , can we go ahead with VRRP,GLBP? Are there any limitation in VRRP/GLBP? Is there any design related issue can we face if we use same group number to all VLANs?
Product details :
Model : Cisco 4506-E
Sup Model : WS-X45-SUP6L-E
IOS : S45EIPBK9-12254SG
I have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies View RelatedI think choose this SWITCH 4506-E and I need running only features L2 Metro, but Idont known what IOS for this!
View 1 Replies View RelatedI have one 4506E switch working in Lan setup as a core switch with WS-X45-SUP6L-E running ipbase IOS 12.2(54)SG1. Each time after reload the switch we found that the clock is getting reset ( time is getting changed ) where as day, date & year is unchanged.
View 2 Replies View Relatedhow can i limit bandwidth on a gig port of 2960 or 4506e switch?
View 9 Replies View Relatedhow can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies View RelatedAfter launching config collection job in LMS 4.2 I can't get job results and receive error message - Unable to get results of job execution for device. I've increased the job result wait time using option in Admin > Collection Settings ... , but nothing changed.Here are screenshots of error message and wait settings I used.
View 3 Replies View RelatedOur customer is try to make a configuration by web interface menu:
Admin > Collection Settings > Inventory
After select the menu below they always received this message:
Error in starting acquisition: unable to connect to server
i have an issue with the lms 4.2 Topology Data Collection. After installation the Topology Data Collection was running normaly, but since first server reload the Topo Data Collect under Inventory > Dashboards > Device Status > Collection Summary is "frozen".Is there any option to stop this process elsewhere? I cannot find anything under jobs in running state or so. Clicking on Schedule only give me the option to start data collection, but lms always returns that the process is running.
View 9 Replies View RelatedI have a problem with the User Tracking and Data Collection on LMS 4.0.1 . I think It crashes every time or freezes. I Have this error if I lunch UT Acquisition :
Failed to start acquisition: Construction of XML data required for UT IS in progress. Please try After Some Time.When scheduling a CM data collection, I have this error: Data collection IS Already in progress.
I detected an error in ani.log line 12266: Exception in thread "Discovery" java.lang.AbstractMethodError: com. cisco. nm. ani. server. topo. Port Channel.portIfIndex ()
I successfully changed the name of the CiscoWorks server last week with the tool hostnamechange.pl.
Perhaps there was an impact on data collection ?
I'm having an issue with LMS 4 where it's failing to collection configuration from devices.
The following is the status of your Scheduled Config collection job:
Job ID : 1045
Status : Job Failed(111)
Description : System config collection job
[Code]....
I researched through this forum and found a thread where the ConfigMgmtServer server wouldn't run. Looking at the processes it says that this service is running normally.
