Cisco WAN :: 3750 / Retrieve Tengig Interface Serial Numbers Via CLI?
Jun 13, 2011it's possible to retrieve Tengig interface serial numbers via CLI? We have a couple of them in 3750 switches, and we need them for our inventory.
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Interface Numbers On A 3750 Switch?
Jul 31, 2012Is there a way to change interface numbers on a 3750 stack but, still retain the config of the physical port?
For instance:
I would like to take the top switch, which has the ports numbered g2/0/1 - 52 and change them to be g1/0/1 - 52. And the bottom switch, which has ports numbered g1/0/1 - 52 and change them to be g2/0/1 - 52. Basically, just swap the interface numbers but, not effect any interface configurations.
Cisco Infrastructure :: 750 - Serial Numbers And MAC Addresses
May 7, 2013I am in the process of implementing 750 Cisco Access Points acros the business. I need to make a note of the serial numbers and Mac addresses for our inventory before I get these configured and sent out to their relavent destinations. The AP's have have arrived in boxes of 10 (75 boxes). The sticker on the box with the barcode is either covered with a postage sticker, ripped, or my scanner will not scan it becaise it is too small. There is a sticker with the serial bundle which is larger and therefore scanable. Is there a way that I can scan this and get the MAC address and serial number.
I know that this is not a technical question but I don't want too spend the next 3 weeks opening 75 boxes and removing each AP individually and recording it.
Cisco :: LMS 4.2.3 Discovery Missing Wireless Controller Serial Numbers
Feb 25, 2013just ran a discovery on a large network and found 49 wireless controllers (5500, 4400 and 2000 series) and none of them are showing the controller serial number. They are all running 7.0.235.0 and I found no bugs that match this issue.
View 1 Replies View RelatedCisco :: C3560 - LMS 4.0 Inventory Collection GBICs And Serial Numbers
Dec 13, 2011I have larger numbers of WS-C3560X-24/24P/48 Cisco switches with1000BaseSX SFP GIBCs installed per switch in my network and they are all added to my DCR just fine. However, when i generate an inventory hardware report GBICs and GBICs serial number is not showing up. Is there any special settings i need to make?
View 6 Replies View RelatedCisco Switching/Routing :: 3750 - Change Stack Member Numbers
Mar 3, 2011I've got a 3750 stack with a 3750-48p being switch 1 and a 3750-12s being switch 2 and switch 2 is the master. I would like to change the stack member numbers. I would like the 3750-12s to be switch 1 and the 3750-48p to be switch 2. I undertand I will have to reboot the stack for the change to take affect but here are my questions: How would this change affect the stack running-config ? will the switchport config follow the change ?
View 5 Replies View RelatedCisco Switching/Routing :: 3750 - Changing Stack Member Numbers
Feb 5, 2012I've got a 3750 stack with a 3750-48p being switch 1 and a 3750-12s being switch 2 and switch 2 is the master. I would like to change the stack member numbers. I would like the 3750-12s to be switch 1 and the 3750-48p to be switch 2. I undertand I will have to reboot the stack for the change to take affect but here are my questions:
- How would this change affect the stack running-config ?
- will the switchport config follow the change ?
switch 1 provision ws-c3750-48p
switch 2 provision ws-c3750g-12s
Cisco Switching/Routing :: 2960S Stacks / 3750 - EtherChannel Group Numbers?
Jan 27, 2012I have a 3750 as core switch, adding 2 stacks of 2960S to connect. I want to establish etherchannel between the 3750 and each additonal 2960S stack, do the channel group numbers between the 3750 and the new 2960s have to match? 3750 has two channel-groups(1 and 2) already configured. Need to know, I would create 2 additional channel groups (number 3,4) for each of the etherchannels between the 3 2960S Stacks and 3750? OR channel-group # is local to the device.
View 5 Replies View RelatedHow To Subnet A Serial Interface
Sep 7, 2011IP Address : 192.168.1.0 /24
I need 50 hosts
I need to subnet for f 0/0 and s 0/0
I know for f 0/0 its 192.168.1.1 /26, but after hours and hours i can't seem how to subnet for the s 0/0
Cisco WAN :: Serial Interface On WIC-1DSU-t1V2 Down
Apr 28, 2012I have a remote site that still utilizes a single T1 connection to me. For multiple reasons we had to scrap the old T1 and have a new one put in. The old T1 resided on a T3 as channel 25. The new T1 is a standlone point to point. I removed the old config from my 7301 and programmed my 3725. I cannot figure out what is going on but the interface stays down/down. There is no loopback turned on, either manually or by the carrier. The AL LED stays amber regardless of whether or not I have a cable patched down. The CD LED remains green when I patch a cable down. LP is not light.I am using a straight through Ethernet cable to connect my 3725 to the smart jack. If you look at the show output below you will see DCD and CTS is down. Since the remote end was working and I just had the tech move the patch cable from one smart jack to another I am assuming the problem is on my side or with the carrierI already tried changing the clock sourced between internal and line. I also swapped out the WIC card for another one. I don't usually program T1 connections. [code]
View 5 Replies View RelatedCisco :: View 3750 Stack Serial Number Inventory LMS 3.2?
Oct 17, 2011I am trying to come up with an inventory report of all our 3750v2 stack switches, but for some reason I could not get the serial number of the member switch under each stack. Can Ciscowork LMS 3.2 see the serial number for each switch under a stack?
View 2 Replies View RelatedCisco :: Simulating ISDN In Lab Using Serial Or Ethernet Interface?
Mar 4, 2012Is it possible to simulate ISDN in a lab using a serial or ethernet interface. I want to setup FR and have ISDN running between a couple of routers with DoD routing.
View 6 Replies View RelatedCisco WAN :: 1760 - Packet Drops In Serial Interface
Feb 11, 2013We have a Cisco 1760 router . We are facing sevier packet drops in the serial interface.
When i swap the router with another router link is working working fine.
Troubleshooting steps taken
1. Swap the serial cable with another working cable : no change in state
2. Reconfigure the encapsulation commands (with PPP and HDLC) : no change in state
3. Try with a decreased MTU packet Ping : no change in state
4. Decreased the Input queue and increased the output queue size using hold-queue in command : Comparatively the packet drop is reducing but still a 10 percent drop is happening.
Cisco WAN :: 7613 Serial Interface Showing Up But Can't Ping
Feb 24, 2013What would cause an interface to show up/up (looped), but you still can't ping that loop?...It is on a Cisco 7613 with an Enhanced FlexWan (WS-X6582- 2PA), with a Mx Serial PA, 8 ports (73-1580-10) and running IOS ver 12.2(33)SRE2 [code]
View 5 Replies View RelatedCisco WAN :: 3845-MB Dropping Pings To Its Own Serial Interface?
May 16, 2013I'm having an issue that I can't quite understand. I set up a test lab to get familiar with EIGRP routing. I have a Cisco 3845-MB with 2 VWIC2-2MFT-T1/E1 cards.sh ip int brief shows UP UP status on all serial ports. I gave it an IP address but I'm having trouble pinging the serial interface IP. It's dropping pings to its own S 1/1/0 interface when pinging from console. I have known good T1 crossover cables 1&2 - 4&5.
Here is the "ip int brief" from 3845-MB
3845-MB#sh ip int brief
Interface IP-Address OK? Method Status Prot
ocol
GigabitEthernet0/0 unassigned YES NVRAM administratively down down
GigabitEthernet0/1 172.30.2.1 YES NVRAM up up
Serial1/1/0:0 10.3.29.2 YES manual up up
Right now it's pinging itself at about 60 -90% success rate... and I can't figure out why it's dropping any packets at all. I have other issues with in the lab as well... but i think this might be my "core" issue.To make matters even more "weird" I've tried two different VWIC2-2MFT-T1/E1 cards and I drop pings with both of them.
Here is a sh run and a sh diag:
3845-MB#sh run
Building configuration...
Current configuration : 1434 bytes
!
version 12.4
service timestamps debug datetime msec
[code].....
Protocols / Routing :: Serial Interface Not Working
Sep 18, 2012I just recently bought a new Cisco 2611 for my home lab and am having trouble getting the serial port to work. I have tried multiple things such as erase startup, switching the cables to rule them out, and even changing IP addresses but none worked. [code]
View 1 Replies View RelatedCisco WAN :: Using Connected WIC2-2MFT As Serial Interface On 1841?
Apr 29, 2012I am trying to use the connected WIC2-2MFT, as the servial interface on my cisco 1841.But it does not show me the option, under configuration interface
[code] What should I do to make this enable on this list?I am attaching the show tech-support, and show version of this device.
Cisco Switching/Routing :: 2811 - New Serial Card Interface Not Detected?
Mar 26, 2012I have existing cisco 2811 (Version 12.4(3c)). I try to add a HWIC serial card into the router but the new HWIC is not detected. There is no new interfece shows up when i do show run. This HWIC is a new card just bought it.
View 7 Replies View RelatedCisco Switching/Routing :: 1841 - Connecting Routers Via Serial Interface
Oct 22, 2012While I managed to connect to each router individually, I decided it was time to connect the routers together via serial; as I don't have any serial cables and need to buy some, what serial cables I need, as well as to ask whether I have the right cards in my router(s) that will allow me to do so.
I bought 3 1841 routers, and all have a 1 port serial WAN Interface Card (WIC 1-T); one router has 2 of these, and one router has a WIC-1B-S/T .. My question is, can I connect the routers with a serial cable via WIC 1-T, or do I need a 2-T
Cisco Switching/Routing :: PPP Multilink Not Coming Up On Serial Interface / 3620 Router?
Nov 1, 2011I just finished setting up a bundle of (2) T1's in a multilink bundle and I'm having issues with one of the T1's not wanting to join the bundle.
The router I'm using on the remote office location is a 3620 router running code c3620-i-mz.121-1c.bin
The campus router which is a 7206 is setup the same exact way with multilink 240 and like I've said, serial 0/0 is joined to the bundle just fine, so we are running off one T1 connection.
The serial interface that is not working is: serial 0/1
Here is a show-run:
interface Multilink240
ip address 172.18.xxx.xxx 255.255.255.252
ip route-cache flow
ip ospf network point-to-point
service-policy output PhonesFirst
ppp multilink
[code].....
Cisco Switching/Routing :: WS-X6708 TenGig Ports
Jun 2, 2013We currently have Cisco WS-X6708-10GE blade installed in our Cisco 7606-S switch. Each of the ports have a X2-10GB-SR tranciever. When I look at the port with the "sh int tengig xx" command I see the following:
!
TenGigabitEthernet 4/1 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c.b0ca.75c0
!
TenGigabitEthernet 4/2 is up, line protocol is up (connected)
Hardware is c7600 10Gb 802.3, address is 001c..b0ca.75c0(code)
Cisco Switching/Routing :: Connecting 4510 TenGig Port To 2960
Mar 10, 2013I am planning on deploying a 2960 switch and will need to uplink it to a 4510 switch. There are 2 TenGig Ports available and I was thinking of uplinking one of them to the 1Gb SFP port on the 2960. Would this work?
View 4 Replies View RelatedCisco :: 3750 - How To Make Interface VLan
Mar 19, 2012i have linksys modem which already working for different v lans then for lab we take other switch 3750 switch and created different v lans. v lans are working fine but we need internet for different v lans for that linksys modem how we can make interface V lan1/
ip address 10.1.1.10 255.255.255.0
ip default- gateway 10.1.1.1
no sh
interface Vlan10
ip address 10.1.2.1 255.255.255.0
no ip route-cache
!!interface Vlan20
ip address 10.1.3.1 255.255.255.0
ip route 0.0.0.0 0.0.0.0 10.1.1.1
ip dhcp pool vlan10
network 10.1.2.0 255.255.255.0
default-router 10.1.2.1
dns-server 10.1.1.1
!
!ip dhcp pool vlan20 network 10.1.3.0 255.255.255.0 default-router 10.1.3.1 dns-server 10.1.1.1
Cisco :: Use EEM To Report On Interface Up / Down 6509 And 3750?
Sep 6, 2011I have just started to discover the power of EEM and am already monitoring config changes on our switches with EEM.I would like to be notified of any interface going up and possibly down. on our 6509's and 3750's This is just to be aware of anyone patching anything in.
View 1 Replies View RelatedCisco WAN :: 3750 - Backup Interface Support On ASR
Jun 20, 2011Does backup interface is supported on ASR?
interface GigabitEthernet0/2/1
description 3750_Stack_1
backup interface GigabitEthernet0/2/2
ip address 100.50.50.242 255.255.255.248
Cisco WAN :: EIGRP Passive Interface With 3750
Apr 26, 2011I have 3750 switch and there are couple of vlans.....i dont want to run the instance on all vlans....so i have decided that i will run passive intreface default command....now my lan link is layer three and i want to run eigrp on that so the command shd be as under?
no passive interface default interface gig1/0/10
no passive interface default interface gig1/0/22
(as i have 2 conections) and want to have two neibours.
Cisco Firewall :: Web Authentication On Layer 3 Interface With Cat 3750
Sep 12, 2012Cisco 3750 with IP Service Image 12.2.55, Trying to enable Web Authentication on Layer 3 interface:
!
ip auth-proxy name bp_auth_proxy http inactivity-time 60
!
interface GigabitEthernet1/0/5
no switchport
ip address 192.168.1.27 255.255.255.0
ip access-group 101 in
Cisco WAN :: 3750 - How To Configure Backup Link Into Switch Interface
Jan 18, 2011I have two 3750 switch.switch A(main) and switch B is connected by OFC but i have another wireless link for backup.Now if OFC goes down then i manually connect wireless link with switch B for this reasons i am faceing a lot of problem. I want without any changing of cable if my primary link goes down then my backup link automaticaly goes up and vice versa .
Switch-A port gi1/0/9 and Switch-B port gi1/0/9 is connect by OFC Switch-A port gi1/0/8 and Switch-B port gi1/0/8 is connect by Wireless link (backup) i attach my network diagram kindly find the attachment file.
Cisco Switching/Routing :: 3750 Show Interface Options
Jan 16, 2012I'm troubleshooting a 3750 switch stack problem where computers are showing input and CRC errors. I'd like to be able to execute a "show interface" command that will show me only the line showing the switch port and the line showing the input errors, but so far I can't figure out a way of combining those two parameters.
If I do "show interface | include Ethernet[0-9]�" I get all the lines showing the port numbers:
GigabitEthernet1/0/1 is up, line protocol is up (connected)
GigabitEthernet1/0/2 is up, line protocol is up (connected)
GigabitEthernet1/0/3 is up, line protocol is up (connected)
[Code].....
Cisco WAN :: 3750 - Establish Interface Dialer On Layer 3 Switch?
May 7, 2012Is it possible to establish a interface dialer on a layar 3 switch?Or is it only interface for routers?I have a c3750 switch (WS-C3750G-24T), and when i try to establish a dialer interface i get an error message:
[code]...
Cisco Switching/Routing :: Cannot Set Route-map On Interface Vlan In Non Default Vrf On 3750
Dec 12, 2012Cannot set route map on interface vlan. which in non default vrf on Cisco 3750.IOS c3750-ipservicesk9-mz.122-55.SE.bin sdm prefer route in enable ip vrf users rd 200:0 route-target export 200:0 route-target import 200:0 interface Vlan201 description Users 1 ip vrf forwarding users ip address 10.31.76.1 255.255.252.0 ip helper-address 10.31.4.57 route-map fromuser permit 10 match ip address fromuser set ip next-hop 10.31.128.155 When I enter "ip policy route-map fromuser" to interface Vlan 201 I heve the message:
% Remove VRF configuration from interface Vlan201 first
Cisco Firewall :: 3750 / ASA 5510 - Allow Access To Server On Inside Interface From DMZ?
Feb 28, 2013My internal network consists of Catalyst 3750 switches segmented into different VLANs. There is a default route on the layer 3 Catalyst switch sending all unknown traffice to the inside Internet of the ASA 5510. However, I'd like to have a separate VLAN for wifi guest access and send all of that traffic through one of the DMZ interfaces on the ASA 5510. I don't think you can have separate default routes based on VLANs on the 3750 switches so my only option is to make the ip address of the DMZ port the default gateway for all hosts on the wifi guest VLAN.
The problem I have is that I have a couple servers behind the inside interface that have services available to the public Internet via a NAT address on the outside interface. I want the guests on the wifi VLAN to have the ability to access the servers on the inside interface using the public address as well, but have not been able to come up with a solution yet.
Here is my config that pertains to this setup:
interface Ethernet0/0description Outside Interfacenameif Outsidesecurity-level 0ip address 76.47.10.x 255.255.255.224 rip send version 1rip receive version 1!interface Ethernet0/1description Inside Interfacenameif Insidesecurity-level 100ip address 192.168.17.1 255.255.255.0 rip send version 1rip receive version 1!interface Ethernet0/3description Wifi Guest Accessnameif DMZ2security-level 50ip address 192.168.60.1 255.255.255.0
global (Outside) 1 interface
nat (Inside) 0 access-list nonat
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (DMZ2) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I've tried the following commands below but no dice.
same-security-traffic permit intra-interface
static (inside, inside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
Cisco Switching/Routing :: 3750 Interface Total Output Drops Incorrect
May 15, 2011I am seeing Interface output drops that appera to be incorrect. When I do "Show Interface gi1/0/20", I will get interface output drops of "4294961382". But, when I do the same command again it shows "0" drops. Is this a reporting error? I am ruinning c3750-ipservicesk9-mz.122-58.SE.bin on a 3750 stack with 2 switches in the stack. [code]
View 10 Replies View Related