Cisco Switching/Routing :: 11501/ 2960 - One Device Boot At A Time
May 18, 2012
My environment have two device ,a cisco css11501 and a cisco 2960 ,when I reboot CSS11501 then 2960 shutdown fa0/41
I command "sh logging | in 0/41" just up down two time,not five times in 10 seconds
.May 17 11:13:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to down
.May 17 11:13:19: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to down
.May 17 11:14:53: %PM-4-ERR_DISABLE: link-flap error detected on Fa0/41, putting Fa0/41 in err-disable state
.May 17 13:44:35: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to up
.May 17 13:44:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to up
I have an doubt about some port in 2960.He have 2 SFP and 2 Fixed Ethernet. Can I use these 4 ports in the same time? Use 2 Ethernet and the 2 SFP with Fiber?
I need to enable/disable a mac access-list on a 2960 scheduled by time. The switch has lanbasek9-mz.122-44.SE6. As the mac access-list can not support time ranges, I tried EEM but seems like it is not supported in this device.
I have a /28 subnet between my internal and external firewalls for L3 connectivity. On our internal firewall, I have a default route for internet traffic pointing to the external firewall (10.10.1.2).
We will be inserting a web filter appliance as indicated on the diagram. The appliance requires an IP address to be assigned to the LAN interface.
What is the best way to accomplish this with minimal impact? Will my default route on my internal firewall have to change to the IP of the web appliance if I address the web appliance on the 10.10.1.x subnet?Should I address the web appliance on the 10.10.1.x subnet to begin with, or create a vlan on the 2960 and a L2 interface on one of the firewalls?
i have a device connected to 2960 switch. It is an access port and i could ping the device from other switches , also from outside the lan. But i am not able to ping the device from 2960 switch alone. I suspected and checked the arp table and it was showing as incomplete. I created the manual arp entry and tried pinging but no luck.
when am trying to plug a PC into the switch, it takes power as the switch is POE . but when trying to plug IP Camera Device it does not take any power. although i have cisco 2960 - 24 ports both PC and IP Camera getting power. while troublshooting by #show power inline , i get nothing as well.
I have some 2960 switches with Lan Lite ios in my infrastructure.And I try to configure them to support "trust device cisco-phone" and "switchport priority extend cos 0" on ports with cisco phones.But LAN Lite image does not support "mls qos trust device cisco-phone".can I use any workaround to trust cos of cisco phone and to remark PC traffic with cos 0?
I have an issue with the device in subject. I need that some server, listed as service on CSS, can contact a content VIP on the same subnet. To allow that traffic I configured grouping on CSS (group 1) with vip address and an ACL that allow traffic from subnet 10.1.1.0/24 toward same subnet 10.1.1.0/24 and I have bound this ACL with sourcegroup 1. The nat and portmap works but never at first attempt, instead since second attempts it works. Seem like a CSS require to much time to create nat entry.
I would like configure a CSS content, that uses the sorry service principal in an advanced way.
I am familiar with the primary Sorry Server command and see that the CSS would send all connections to the named service that is configured as the primary Sorry Server.
What I would like to do is to configure the CSS, so that once it’s decided it’s in a “sorry” state (all the services that are configured with “add service” are down) that it load balances to a different set of services.
To explain what I’ve been trying to do in the form of configuration on the CSS, I’ve pasted some pretend config below.
Connections come into IP address 1.1.1.1, which normally get load balanced between 9.1.1.1, 9.1.1.2 and 9.1.1.3.
If 9.1.1.1, 9.1.1.2 and 9.1.1.3 are all down, the sorry service is used and the CSS starts passing traffic to 1.1.2.1, which I want it to load balance between 9.1.2.1, 9.1.2.2 and 9.1.2.3.
The order that I have applied the config, is different to the below, as I set out to configure in this order: secondary services, secondary content, sorry service, primary services, primary content.
The order of the config below is different, because I wanted it in the order that the traffic flows and the CSS won’t take the config in that order!
The wall I have ran into, is that when I try to create the service I have named “Sorry Service”, I get the following error:
%% Service IP Address conflicts with a local I/F, VIP, mg mt route.
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
My Internal Wireless adapter not working each time boot up I am using Windows 7.
I have to diagnose each time and click fix for it to enable the internet to be on. Why is it disconnecting me from connecting to the internet all the time upon startup ?
Here are the details-
Diagnostics Information (Network Adapter) Details about network adapter diagnosis: Network adapter Wireless Network Connection driver information:
When I look at the local area connection the status is acquiring network address and just sits there. When I try to repair, it states that windows couldn't finishing repairing because it can't renew my IP address.
On cisco and am having some issues with intervlan routing. I have followed the vids and manuals but just can seem to get this working. I have the following network lab set up.
Vlan 10 = 10.70.1.9/24 Vlan 20 = 192.168.0.1/24 ME2400 firmware ROM: Bootstrap program is ME340x boot loader BOOTLDR: ME340x Boot Loader (ME340x-HBOOT-M) Version 12.2(35r)SE3, RELEASE SOFTWARE (fc1) [Code]...
I recently installed a Dell 5324 switch as my main switch and it's my first time using a managed switch at home. One thing I've seen as an issue in a corporate environment, and now here, is that managed switches tend to take a bit longer for a port to be active. Ex: a PC is turned off, I turn it on but if the PC boots up very fast the port may not be ready. All mounts fail. This is the issue I am facing with my HTPC. It runs Linux and has a SSD, and it has no UEFI bios to slow it down (which is good, I hate UEFI for that) so it's up and running within 5-10 seconds of pushing the power button. The network mappings fail because the port is not ready by the time it gets to the script that mounts everything.
I unpacked a new 3560x and went to put our standard code version on it c3560e-ipbasek9-mz.122-53.SE2. Everything seemed to upgraded fine but it won't boot to a console prompt. It seems like it loads the IOS image fine but can't get passed the Front-end Microcode IMG MGR: Programming device 0. [code]
I have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
I cannot boot IOS, when i reload this switch it go to ROMMON. I try to uploand IOS but it still has problem. i think i may wrong some point during i did uploand.
I tried to upgrade IOS from SXI2a to SXI9 in cat 6506 VSS. But the problem is that switch always boot with old IOS. I put the new IOS in sup-bootdisk and slave sup-bootdisk, bootvar is ok with new IOS: [code] Show bootvar is ok but switch always boot with old IOS SXI2a, some bug in IOS sxi2a???, I will try to delete de old IOS from sup bootdisk and try with the new one only.
my Catalyst 3750 switch. Following a power cut the switch no longer boots up. The SYST light flashed green but no POST checks are made. I cannot see any boot messages from the console port either. The switch was on a UPS but some thing may have damaged the switch.
What would happen if I installed a 32MB (MEM870-32F=) flash upgrade card in to a Cisco 871 router that already had 28MB flash on-board already? Would the router boot seeing 52MB (the max this router can have) or would it fail completely since the combined total would be over 52MB?
I know you can get a 24MB upgrade card but they are quite expensive.
i want to boot my Router's IOS from TFTP server but when I use the command: boot system tftp c2801-adventerprisek9_ivs-mz.124-24.T7.bin 172.16.10. 200; after that I write-mem, it shows the log:
-Router#wr -Building configuration... -ROMMON: out of room in table, cannot set "BOOT"
And when I reload the router, it cannot boot IOS from TFTP Server, sure my TFTP work well and 2801 can ping to TFTP.
I can see the boot file at 192.168.100.1 but I can never get into the GUI. The unit boots up, fans running. Eventually the power light flashes red. I don't have the unit hooked up to anything else except a laptop to try and configure it.
document which explians normal booting sequence in a 6500 Switch running IOS. What I am looking for is in which order the image is loaded in SUP, RP, SP etc
I have a 4503-E on my work bench. It's been out of production for a year or so. I started working on it last week. I think I may have cause a boot up problem. It comes up to ROMMON, but then I need to type "boot" to get it to come up all the way.
config-register = 0x2102Autobooting using BOOT variable specified file.....
Could not find a valid file in BOOT environment variable.BOOT variable can be set from IOS. To find currently setRom Monitor variables, please type 'set' command.
For choosing a boot method, type 'confreg' command. rommon 1 > For choosing a boot method, type 'confreg' command.rommon 1 >
At this point I type "boot" and it proceeds to the normal bootup. (Below are a couple more print outs)
RG-4503#RG-4503#dir /allDirectory of bootflash:/ 1 -rwx 12185732 Feb 21 2008 08:23:59 -06:00 [cat4500-ipbase-mz.122-31.SGA3.bin] 2 -rwx 14787732 May 21 2008 01:00:30 -06:00 cat4500-ipbasek9-mz.122-44.SG.bin 3 -rw- 7315 Dec 31 2012 07:13:15 -06:00 *** 61341696 bytes total (34360532 bytes free)RG-4503#RG-4503#RG-4503#show run | include bootboot-start-markerboot-end-markerRG-4503#
It looks like there is nothing between boot-start and boot-end.
i have a Cisco 6513 it is used one, i have tryed to boot it but it did not work, it alwayes go to rommon mode and i am not able to know what is the issue,
when it boot i get the below outpot from the switch.
System Bootstrap, Version 8.1(3) Copyright (c) 1994-2004 by cisco Systems, Inc. Testing lower main memory - data equals address
One of the 6500 was going in bootrom mode, so I have formated the flash disk using the other Cisco 6500 switch and copied IOS file to the boot disk. But the 6500 booting failed.
Customer is using SUP720 with SP rommon image version 8.1(3), he is trying to boot the new ios image from disk0, but he gets invalid magic error. he fomat the disk0 but still he gets error when he boots from disk0. He suspect that it can't be flash problem but can be software of hardware as he has two flash with same issue on 2 switches.
Customer wanted to recreate, I tried in the lab, i was able to load from disk0, but sup in lab had 8.5(4).
Customer wanted me try with 8.1(3) version. But i was unable to downgrade the SP Rommon image. SP rommon is running in Gold region and I loaded the 8.1(3) from both disk0 and sup-bootdisk, even preferrence was given to region1 but still sup came up with gold region itself.
* Will i be able to downgrade from 8.5(4) to 8.1(3), if so, what are the steps.
* is there any limitation or bug where 8.1(3) will be unable to read disk0.
I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
I'm having difficult getting this switch to boot from flash. I do not understand why it is trying to load "b1" from "bs1" instead of something from flash. [code]
I encountered an issue while trying to boot Catalys WS-C4948-S switch. I power on the switch and I'm able to see the boot messages thourgh serial console cable. But it gets stuck at line "Image text-base: 0x1000000, data-base: ..... ". Also I can enter into rommon mode. I tried to use different kinds of IOS images, tried to boot from tftp but with no luck, the issue is the same.
There are no erros on the screen, it just gets stuck when it enters into IOS, so I don't see the IOS prompt.
