Internal Wireless Adapter Not Working Each Time Boot Up
Sep 20, 2012
My Internal Wireless adapter not working each time boot up I am using Windows 7.
I have to diagnose each time and click fix for it to enable the internet to be on. Why is it disconnecting me from connecting to the internet all the time upon startup ?
Here are the details-
Diagnostics Information (Network Adapter)
Details about network adapter diagnosis:
Network adapter Wireless Network Connection driver information:
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
I have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
I have a Dell laptop, (Inspiron Mini).When i re install the software, the wireless network adopter disappeared, how can i re install it to receive the wireless network?
When I look at the local area connection the status is acquiring network address and just sits there. When I try to repair, it states that windows couldn't finishing repairing because it can't renew my IP address.
I built a computer a while ago, from a reasonably low budget. Ever since the very first boot up, the wireless card (TP-Link, unable to find model currently, will add later) only works on the second consecutive boot up. I have no idea why, I have not found anything relating to a problem like this, the computer doesn't even appear to know that there is a wireless card in it. Instead the icon shows a cable, suggesting that the computer isn't connecting with the card.
I recently installed a Dell 5324 switch as my main switch and it's my first time using a managed switch at home. One thing I've seen as an issue in a corporate environment, and now here, is that managed switches tend to take a bit longer for a port to be active. Ex: a PC is turned off, I turn it on but if the PC boots up very fast the port may not be ready. All mounts fail. This is the issue I am facing with my HTPC. It runs Linux and has a SSD, and it has no UEFI bios to slow it down (which is good, I hate UEFI for that) so it's up and running within 5-10 seconds of pushing the power button. The network mappings fail because the port is not ready by the time it gets to the script that mounts everything.
My environment have two device ,a cisco css11501 and a cisco 2960 ,when I reboot CSS11501 then 2960 shutdown fa0/41
I command "sh logging | in 0/41" just up down two time,not five times in 10 seconds
.May 17 11:13:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to down .May 17 11:13:19: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to down .May 17 11:14:53: %PM-4-ERR_DISABLE: link-flap error detected on Fa0/41, putting Fa0/41 in err-disable state .May 17 13:44:35: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to up .May 17 13:44:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to up
I'm running an exchange server beings my 2800 router and its all working well i have setup NAT and OWA is working well when external and on the internet but when the phones are on the internal wireless OWA isn't working and if u telnet the external ip on that forwarded port it doesn't forward i believe this is the fact the port forward rule "ip nat inside source static tcp 10.0.100.7 443 interface Dialer0 443" is for the dialer interface only and as I'm internal nothing but I'm show to forward any request on that port.. ill include the config below
setup a DHCP server on a WLC 2504. I'll try to resume my configuration:
I have 2 networks: inside users (vlan 1) and external users (vlan)
My controller uses the port 1 to connect to the switch, which has a trunk with WLC.
I have two routers, one using vlan 1 (192.168.3.0/24) and one using vlan 10 (200.X.X.X). All ports to these routers are access ports on their respective vlans.
I have 2 SSID, one for inside, other to outside. Inside is working very well.
To the outside I created a DHCP escope and already set the IP of the management interface 192.168.3.119.
I have been trying to create a Guest WLan on my 4402 WLC system and have found several confilcting documents explaining the procedure. During this process I have notices that although the current corp wireless works, there was never a virtual interface created for it. Instead it uses the same Wlan/Vlan as the ap manager and managemnt interfaces. Could this by why I cant seem to get the Guest access working? or is this not a problem after all since the wireless does work.
The wifi card in my laptop may be bad. I can find a network but cannot connect. It says that signal lost, but source is in same room and works with other laptops. Can I just add a external USB WiFi adapter to bypass my internal one?
having a problem with my Linksys wireless adapter: the light will flash a few times when I plug it in, then it will turn off. It won't let me connect to the internet or my printer.It's not the port: it is recognized when I put it in any other port, but it still won't connect. I think it's a virus, but my antivirus software isn't showing anything when I run a full scan (I use Malwarebytes Free). I'm gonna put AVG on a flash drive from another computer and try to use that later today, but right now I've been thinking that I might have to back everything up and reinstall windows.
-Windows Vista- Home Premium
-Linksys Wireless USB Network Adapter (I think it's WUSB600N, not sure though)
I just bought a wireless adapter for my PC, linkseys ae1000. It's been approximately a week, and the computer has been on most of the time...roughly 8-12 hours of a day, not in use the whole time, however. Then today when I booted up my computer, the wireless adapter didn't turn on! It's like a little USB thingy...and when i took it out, it was extremely hot, even though it wasn't doing anything! I tried multiple USB slots as well, to no avail...What basically happens is I put in the CD-rom installation disk, then when it prompts me, I plug in the adapter...and then it takes me to the connect to network screen, at this point the adapter has it's little wireless light blinking, then I try to connect to network, the light stops blinking and turns off, and it just tries connecting to the network for an eternity.
I just purchased a Medialink MWN-150N Wireless N USB Adapter. I have never had wireless on this computer and I have always been hard lined directly to the router without any problems of connecting to the net. I installed the software, am able to connect to my network with full bars, but have limited/no activity. I unplugged everything and hooked up the modem 1st, router 2nd, and turned on the computer last, but no luck.
bought this wireless adapter. installed drivers and everything but it doesn't work. when i plug in the device, the network icon in the system tray doesn't change. it won't let me choose any wifi signal. tested it on other computer and laptop and it works no prob. i used to have one before and i remember it worked okay but now it's not working anymore.
above usb adapter first worked fine with windows7 then i used belkin G usb adapter but it is not worked, so again i switch back to 11n usb adapter but not it is not connected?
I have a D-Link wireless adapter (DWL-G122) that I have been trying to install on a Windows XP computer. After various uninstalls and reinstalls of the drivers and programs that come with it, I have found currently the best way to get it to work is leave the D-Link programs uninstalled and have Windows install the driver itself.The problem is, it doesn't seem to keep the drivers on restarting, so every time the computer is restarted, it must be installed again. This is not ideal.It occasionally worked when I installed from the CD, but the D-Link programs that would install with the drivers created problems of their own.
To get this Wireless adapter RNX-N150UBE to work we have to go to the device manager in Windows XP Pro, uninstall it and re-install it every time the computer is started.
I cannot connect to the internet wirelessly on my Toshiba A205 laptop. I've run the diagnostics and it seems the adapter is not working. When I look at the system I can only see the Marvell Yukon PCI-E ehternet controller. That is not the wireless, is it? I think I could change it but I'm not sure which to get and where it is.
I have a realtek wireless usb adaptor on my hp desktop that was working until I took it out of the usb on the front of the tower and plugged it into a usb on the back of the tower. Now I can't get internet at all even if I move it back to the front! My network doesn't show up under connections. Both the playstation 3 and the netbook are picking up the wireless signal from the router.
I reformatted my father's laptop, upgrading the OS from Vista to Windows 7 but now the wireless network adapter isn't working. Basically, the laptop doesn't know that it has wireless. In device manager there is an exclamation mark against the "Atheros AR5007UG Wireless Network Adapter" entry. I've tried uninstalling the driver and reinstalling it, restarting the computer, updating the driver etc but it always fails to install the driver correctly. I don't know for sure the model of the network adapter, (windows tells me it's atheros but I'm not convinced seeing as the driver always fails to install) so I can't go to the manufacturer's website to download the latest drivers. I opened up the laptop but couldn't see any brand names on the network card. I don't have the cd's with the drivers on them.
The laptop is an HP. The network adapter is having the common problem of being unable to connect to secured wireless networks. I know this is a common problem and I HAVE tried everysingle suggestion posted on this forum, including but not limited to: reinstalling drivers, making sure the adapter is configured for the appropriate gateway and even doing a full restore to factory defaults. NOTHING has worked.
I have a problem with a wireless adaptor on a Toshiba Tecra (A11-1EE - PTSE0E-065052EN) running Windows 7.The wireless adaptor works fine but every now and again it will just stop working. The operating system says that the adaptor is turned off but it isn't. I've checked the driver but it is up to date.I have to disable the driver and then enable it again and then the adaptor begins to work correctly again.
I'm using HP Pavillion dv3-2165ee Win7 32bit with Atheros A9285 WLAN adapter.problem is that my notebook is not detecting any wireless network.it is as if my adapter is turned off. when i switch it on, Bluetooth works but WLAN dont. I tried turning it on/off couple of times but it didnt work. I'm not sure if is just a timing, but it started when im on a cafe when i plugged in my friend's flash drive then after a while i lost all available wireless networks that time.At first i assumed it's because of virus, so i tried driver reinstall/reformatting/recovery disc but nothing solved the problem.
When I browse the net, i saw this Xirrius Wifi Inspector so i downloaded it with a cable connection then when i used it, it was able to detect the wireless network i have in my house but just for a couple of seconds, and the network disappeared.I tried other drivers, but i didn't work. As i've said earlier it is as if turned off.I've run this diagnostic test from Atheros driver and got this result with my WLAN switched on.While on this screeny, you can see in HP Wireless Assistant that my WLAN & is enabled, but at the same time Windows Mobility Center is indicating that my WLAN is not just turned off but it is like there is nothing there.
The wireless adapter keeps saying unidentified network, I can connect from other computers and they are all working fine.
Edit: Forgot to mention its a ASUS wireless n-15 adapter, also the system is a Windows 7 64 bit. Also, has a ip address 169.x.x.x which i know means no internet connection.
while my younger brother borrowed my USB adapter to fix somerhing on his computer (he normally doesn't have net), I was using a flash drive. I had left the drive in, and my (very heavy) DVD drive was dropped on it, breaking both the front USB 2.0 ports and the flash drive. So I had to put the adapter in the back ports. The first few hours were fine, then net cut out. I repaired the connection, only to have to keep repairing every 30 seconds to 10 minutes. Then it stopped working altogether. I've attempted re-installing drivers, but when I do, my computer tells me that the driver I'm installing from my hard drive "Has no information on my hardware", but it's the correct driver and version for my hardware.
Specs are as follows: Windows 7 Ultimate 64-bit 2.26 P8400 GHz Intel Core 2 Duo 4 GB DDR2 400 MHz RAM NVIDIA GeForce 9600M GS Graphics
And of course, the Atheros AR928X Wireless Network Adaptor.It seems that no matter what I do wireless capability cannot be enabled. I tried turning the wireless capability button on and off but to no avail. Then I pressed FN+F2 and it didn't fix it. In both those situations a box which displays the status of the wireless LAN connection comes up, however, it reads "OFF" regardless of me performing the above two "fixes." According to my computer the card is enabled and I tried uninstalling and reinstalling the device driver but nothing changed.
