I have WLC 5508 in my office and i am asked to backup file configuration from WLC but when i remote WLC to get the upload configuration file via tftp it doesn't work.
But when I try to use direct connection ( point to point ) with WLC and my laptop i can get the upload configuration file. is there something wrong, actually i have connected with that WLC i can ping and telnet that device
i have few catalyst switches (2960, 3750) and i can't upload to them any files by tftp from my laptop, but i can download from them, and this bug don't appears on two routers.I was change tftp server, type of connection (wifi, cable), turn off firewall on win7, but no dice.
View 2 Replies View Related5508 controller is at the headquarters which can be normally pinged, telnetted, http'd and tftp'ed....at the remote site, controller can be pinged and http'ed but cannot be telnetted and tftp'ed.there is a complete tracert from the remote site pc all the way to the controller.from a switch at a remote site, the controller can be telnetted. but from a pc on the remote site (which belongs to a remote site vlan), it is unable to telnet and tftp the controller.all active components can be telnetted from the remote site, such as the core switches and routers at the headquearters, except the controller.upgraded the controller code to 7.2.xxx in headquarters but still unable to telnet and tftp the controller from remote site.is there any more settings on the controller for telnet and tftp?what could be the problem why the controller is not available for telnet and tftp from the remote site?
View 12 Replies View RelatedWe recently did a forklift upgrade on our campus and installed 3502i's, 3502e's, and 11 5508 WLC's. Our students are complaining about slow connections in several areas of the campus.In our testing and basic trouble shooting our Apple laptops have no problems but our windows laptops are showing a very slow connection rates 264kbps downloand and 366kbps upload. The window device has current drivers installed.
View 14 Replies View RelatedIs there a way to backup the configuration file to a tftp server? I've tried "copy start tftp" and copy run tftp". No luck, I get an error message.
View 1 Replies View RelatedI have in the past downloaded the webauth bundle to a wlc 5508 running 7.0.98 successfully. I am trying to upload a new bundle after modifying the AUP but I get an error after the download to the wlc.
The error with FTP or TFTP is
% Error: Webauth Bundle file transfer failed - Unknown error - refer to log
I've tried to copy the unmodified bundle from the zip and get the same error so I don't think it's the login.tar file.
I have two Cisco WLC 5508 controllers that I'm trying to set-up for our new corporate WLAN. I've gone through most of the configuration fine but have ran into an issue uploading a signed certificate to one of my controllers. I should point out that I have managed to upload the certificate successfully to one of the controllers, I just can't seem to upload it to the second.The issue is as follows:
- I've logged into the controller, gone to Security -> Web Auth -> Certificate -> Download Certificate
- I've specified my tftp server details and selected apply
- the process begins and I can see through my tftp client that the controller is attempting to copy and install the certificate
- The controller tries to install the certificate but fails, reporting the same
I need to transfer a config from a TFTP Server to a 4507 and a 6513. When I transfer the config to both those switches, does it require a reboot?
View 5 Replies View RelatedI am using multiple cisco 2811, 3745 routers and 2950,3550 switches if I need to copy running configuration I have to go to each device and say copy run tftp: <address> Is here any way that automatically by schedule one a week or a month configuration copy from all devices to tftp server?
View 2 Replies View Relatedupload configuration to the Cisco 877? normaly i am using the TFTP server,
View 30 Replies View RelatedWhat is the ratio supposed to be between the download speed and the upload speed in a normal working configuation? My webpages are taking forever to load. I used this speedtest... url...
-download speed: 7.427 Mbps
-upload speed: 0.006 Mbps
My provider is cable, Brighthouse, hooked up to their Scientific Atlanta modem and from there it is hooked up to a Belkin Connect N150 wireless router. I am not using the wireless on my laptop but am wired directly to the router. [code]
how to backup a Cisco Wireless Access Point Controller 5508.
View 2 Replies View RelatedSo we have a Cisco 5508 controller that is managing 15 AP's in one of our buildings.I am running 2 wlans, one is internal access via (wpa) radius, peap and domain login...that works well now
The other is a guest lan, that is only allowed to surf the web.
The question from our security group, is there a way to restrict wireless access to ONLY a corporate approved list of devices.
As it stands right now, we only support Blackberry's as our mobility device. All local data is encrypted. The issue here is our testing shows that with an Iphone (not approved) it is very easy to connect to the WPA network if a user knows how to enter in their domain credentials. From there they can browse our internal web servers and download corporate data to a non approved, non encrypted device such as the iphone.
Any link that will give configuration examples of a wireles anchor config with one controller in a DMZ. I have tried this on my own and have some problems in my test enviorment. I believe my issues were with the firewall but not exactly sure.
View 4 Replies View RelatedI am trying to come up with a standard way to configure controllers for my field guys. I'd like to just have them paste in a config that has all the settings, like we use to be able to do on aIOS. I am not seeing away to break out of the wizard so that they can just paste in a config. Do you have to go through the wizard in order to get to a CLI ?
View 8 Replies View RelatedWe have implemented VSS on Cisco 6504-E switches using the 10GE links on the Sup-720-10GE. Two Cisco WLC 5508 controllers are planned to be connected in a LAG configuration, (consisting of eight links per LAG bundle) to each of the 6504-E chassis( Total of four WLC, two for primary and two for secondary). WLC HA feature may be implemented on the primary and secondary WLC controllers using the 7.3 latest code release.
View 9 Replies View RelatedWe have 5508 controller (redundant) & would like to configure Staff vlan to get authenticate with active directory.i am new to the controller device & want to configure controller with active directory (windows 2012).
5508 controller (Active & Standby) with 48 Access Point.(configuration Done) Guest Vlan (only for internet Access) controller based web authentication configured.
Staff Vlan ( inside & outside ). Need to configure with LDAP authentication?
I have found some samples on the FlexConnect setup for the controller side. However none of the documents mentioned how the switch port should be configured that goes to the controller and AP.
At this moment I have a Cisco 5508 configured in CAPWAP mode with 20 APs. I would like to use same controller for connecting one of the remote sites with 2 APs in FlexConnect mode. Current the 5508 to switch port is configured as 802.1Q port. All CAPWAP AP ports are configured as "switchport access vlan X" where X=capwap VLAN. Need to know how the switch port should be set for the remote site where flexconnect APs connect.
I just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
I have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
View 17 Replies View RelatedIs there any additional configuration to be done on the 5508 WLC for Wireless Laptop / Voice Roaming? I tested with Wireless IP Phone and found some blankness in voice , whereas i have other access point nearby , which wasn't switching over easily .
View 3 Replies View RelatedI have 2 5508 controllers in a mobility group. Any good way to keep the configuration between the 2 controllers synched up?
I thought about copying the config from my primary controller to the secondary controller, but I would think there is a more elegant way to make this happen.
I would like to know whether there is any command that shows the configuration of the wireless controller (5508) like when you upload the configuration file from the GUI of the WLC. In other words, I don't want to show me all the verbose running configuration as the "show running-config", but a brief configuration as for example described below: [code]
View 2 Replies View RelatedI am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies View RelatedI recently tested the process for a customer of defaulting a Cisco WLC to factory configuration and then restoring the configuration from Cisco NCS. It was not seamless to say the least and I wonder if I have just gone about it the wrong way.
Have have set the NCS platform to configuration sync with the 5508 controllers at 04:00 every day and prior to the controller defaulting I ensured that NCS also reported that the config was in sync. I have also set NCS to complete a tftp backup of the controller every night 23:00 - interestingly though I have no idea where this is stored on the NCS platform ( a VM appliance ) or what it's file name is.
Anyway my experiences where as follows:-
1. defaulted WLC and via serial CLI ended up at the configuration wizard.
2. Set the correct LAG, management IP, host name that NCS knew this controller by.
3. To test things just created a dummy WLAN ( SSID ) as I assumed this would be overwritten ( big mistake ! ).
At this point I connected the controller to the network and tried to restore the configuration from the config sync version.
First problem - you have to remember to set up the SNMP community string you were using as it is needed by the configuration sync process. After adding this to the controller I could push the configuration to the controller.
Second problem - failed to add the first WLAN from the backup as I have added the temporary dummy W LAN via the wizard and NCS reported a conflict. So had to delete WLAN ID 1 from the WLC GUI directly and then the config push no longer reported this error.
Third problem - for some reason did not add the TACACS server details - reported the error that it could not added them. I manually added these via a template via NCS and all was well.
Fourth problem - all but the first WLAN was in the disabled state - had to re-enable all of the WLANs.
Fifth problem - any default items I had disabled or removed have not been saved - therefore I have removed the public and private SNMP communities - but these were still on the WLC after the restore. I have disabled unused ports not in the LAG as they show an error in NCS - these where not disabled after the restore.
So all in all not a very satisfactory restore process from NCS to an defaulted WLC ( meant to simulate to the customer what would be needed if they had to replace a controller due to hardware failure ).
I can't get connectivity from laptop to AP using cross over or straight through cable to do a tftp transfer from tftp server on laptop to ap.
I held the mode button on ap and powered on to get to rommon. The ap has no ios so it goes to rommon anyway. ap light is blinking red.
ap: set
DEFAULT_ROUTER=10.0.0.1
IP_ADDR=10.0.0.1
NETMASK=255.255.255.224
[Code].....
How to, for the most part, setup 802.1x via wireless. I'm using two 5508 WLCs, and Cisco ACS. I will setup the user account/password information via Cisco ACS and User Identity and Hosts. I know from the WLC 5508 web admin tool that I can choose 802.1x in the security parameters. I only have a few question. We have two wireless networks, one is wide open and provides internet access, the other will provide internal access for select users. I am setting up 802.1x on the internal wireless lan. Do I need to configure any 802.1 configuration commands on the switch in order for this to work, if so where would be the locations to do this at? Also, if there is a MAC isolation configuration option I can configure to not allow other hosts on this specific wireless network to communicate with each other?
View 3 Replies View RelatedI am trying to TFTP an image to a Cisco 2504 WLC. The management interface is 10.1.1.1 /24 and I have my PC connected to a port on the WLC with the IP address 10.1.1.10. However, I still do not have connectivity between the PC and WLC.
View 3 Replies View RelatedI've got a new 5508 wireless lan controller and can ping the ip address of the management interface, but can't access the GUI at the management interface's ip address. I can access the GUI on the service-port interface. No static routes in the controller; trunk appears to be set up correctly.
View 5 Replies View RelatedI have to upgrade our Wireless LAN Controller modules inside 2811 routers.I downloaded files from Cisco site, verified MD5 hashes and hoped it will be pretty easy.the problem is, that WLC is only capable of code upgrade via TFTP and that the image size is ~80MBTFTP transfer hangs at approximately 64MB at the exact same packet number[CODE]
View 4 Replies View RelatedI am trying to convert two Aironet 1141n access points to autonomous stand-alone units. I have connected the console cable and I can see the unit giving information in the console window, but I cannot type any commands. When I try to get the unit to upload the c1140-k9w7-tar.default file by holding the mode button in for 20-30 seconds, it shows it is examining the file, and then states that the connection to the tftp server has timed out. My windows firewall is off, the interface is configured as 10.0.0.2 255.255.255.0 and the tftp server is showing that.
View 15 Replies View RelatedI'm having trouble TFTPing a configuration from my 851 Router to my computer through a IPsec VPN tunnel that this router is connected though. I am able to telnet and ping all devices on the far-end with no problem. I can TFTP a config from a switch behind this router, no problem. I am guessing this problem is related to an ACL on the router. I am also having trouble connecting to this router using the Cisco Config Professional. Discovery will fail, with connection could not be established or HTTP service is not enabled. I have enabled HTTP service. The CCP works fine when I am on the router's subnet.
View 3 Replies View RelatedI am using filezilla (ftp client) to upload to file server as well as other sites including free host and 000webhost, on large files my upload fail near the end,This does not happen if I bypass my e200 router, so it must be something about the the e2000 that is causing the failures.
View 2 Replies View Related