Is there any way to do layer 3 security like a web login to an LDAP server on the wireless portion of the SA 520W?I'm asking because we have this set up on many of our Cisco Wireless Controllers and I would like to do it on the SA520's as well. I'm not sure if it's supported though.
View 2 Replies
My company ordered NAC and ACS 1120 My question is Can i configure 802.1X security through ACS server and NAC in layer 2 Inband Virtual Gateway.for campus switches.Is it the good design to have double security for switch ports. 1st is 802.1X and 2nd is NAC in layer 2 INBAND VG?
View 1 Replies View Related'm able to setup my 3750e switch to login through a radius server with my company user id and password but would like to be able to set it up that when I log in it drops me on the enable prompt. Right now I have to type >en.Then the enable password.
View 1 Replies View RelatedI've set up a ACS 5.1 Server an want to use it with our LDAP System. Therefor, I'm trying to login to a Cisco 1841 by using my LDAP Account, but it dosent work. The ACS seems not to know that it should use LDAP, because I get,"22056 Subject not found in applicable identity stores"LDAP is configured as Identitiy Store, the bind test works successfully and I created a sequence, where LDAP is at first position. What goes wron?? (TATACS for loal ACS Users works)
View 3 Replies View RelatedI have a SA 520W with the following configuration:
-WAN port: Internet access for web browsing and QuickVPN access for remote users
-Optional port: Configured as WAN, for VPN access to another office (Office 2) in the same building throung a public network
-Ethernet ports: Computers on Main Office.
So far I have been able to configure communication between Main Office and Office 2 via VPN.Office 2 have no Internet access, so I need to share the Internet access from Main Office.QuickVPN clients have no access to Office 2, only to Main Office.
Everytime I boot up my Winows 7 desktop the new E900 requires a security key to login.
Can't seem to get the settings right to automatically login like my laptop does. Routers can be humbling.
I need to integrate a 2504 WLC with a windows 2003 LDAP server for extented authentication, is there any guides available for this ?
View 1 Replies View RelatedPreviously, I was able to configure our Easy VPN Server with local authentication.But now, I am trying to use LDAP authentication to match with our policies.
My router is a Cisco1941/K9.
Current configuration : 5128 bytes!! Last configuration change at 13:25:16 UTC Tue Aug 28 2012 by admin! NVRAM config last updated at 05:03:14 UTC Mon Aug 27 2012 by admin! NVRAM config last updated at 05:03:14 UTC Mon Aug 27 2012 by adminversion 15.2service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!!!aaa new-model!!aaa group server ldap ASIA-LDAPserver server1.domain.net!aaa authentication login ciscocp_vpn_xauth_ml_1 localaaa authentication login ASIA-LDAP-AUTHE group ldap group ASIA-LDAPaaa authorization network VPN_Cisco localaaa authorization network ASIA-LDAP-AUTHO group ldap group ASIA-LDAP!!!!!aaa session-id common!!no ipv6 cef!!!!!ip domain name domain.netip cef!multilink bundle-name authenticated!crypto pki token default removal timeout 0!crypto pki trustpoint
[code]....
Does Cisco Secure ACS 5.3 support LDAP authentication with Apple Mac OS X server? One of our clients require an access control system. The major portion of the network consists of Apple Mac OS X 10.7 (Lion) Server and clients. They were using MAC-address based authentication along with LDAP through Cisco Wireless LAN Controller. But now the number of users has exceeded the maximum number of MAC addresses supported by WLC (2048). Hence we suggested ACS appliance to overcome the limit. My doubt is whether ACS 5.3 appliance can communicate with the Mac server and perform LDAP authentication.
View 2 Replies View RelatedI'm having a problem with a WLC 5508 and a LDAP on windows server 2008, I already config everything on the WLC, but when a user try to authenticate I have this debug result:
*aaaQueueReader: Jul 15 19:27:07.384: 00:1b:77:7b:19:aa Returning AAA Error 'No Server' (-7) for mobile 00:1b:77:7b:19:aa
*aaaQueueReader: Jul 15 19:27:07.385: AuthorizationResponse: 0x3c9ceac4
*aaaQueueReader: Jul 15 19:27:07.385: structureSize................................32
*aaaQueueReader: Jul 15 19:27:07.385: resultCode...................................-7
[code]....
the linux server should be configured with LDAP, so that any user should not login into that machine by local user credentials but by his intranet credentials.
View 1 Replies View RelatedI have a ACS 4.2 under windows, I setuped it to authenticate routers by RADIUS and TACACS+ protocols. now I have some devices whitch know only LDAP protocol. How can setup ACS as a ldap server to authenticate those devices?>
View 1 Replies View RelatedI'm having a problem configuring local EAP Authentication using CA (Windows Server) and LDAP server. I followed the URL:
[URL]
but it seems that CA has no effect. Any wireless client who has his own LDAP account can access to the network.What I want is just allow some wireless clients to access if they have approved CA before.
We are looking for a solution to avoid VPNs to encrypt data between HQ and Bldgs (point-to-multipoint) Gigabit fiber(untrusted media).Is there any cisco's product providing layer2 encryption over Giga fiber?The HQ has a 6509s and remote bldgs have mixed of 3750s,4500s in trunks.
View 2 Replies View RelatedI have a Cisco ACE 20, and I´m trying to set up a serverfarm for my radius server to load balance ldap udp accounting packets. The ACE has an LDAP authentication probe but I see no native way of setting up an LDAP accounting probe, without resorting to probe scripting.
View 2 Replies View RelatedWhen I play call of duty mw2 and mw3 I always disconnect from servers and my ping is always high. So I tried to forward some ports via it says " The EchoLife-HG532 will not allow you to forward enough ports, to run Call of Duty - Modern Warfare 2. You should try using the DMZ portion of this router if it is available.Alternatively you can try switching the router to bridged mode. You will need to contact your ISP to switch to bridged mode, so they can make the required changed on their end." So I need a solution which would enable me to play these kind of online games with low ping and without disconnecting. My router's speed as per the ISP i'm using is 4094 kbit/s
View 3 Replies View RelatedI have a cisco ASA5505, with base license, it appears I can only have 2 ssl/webvpn connection running at any one time. How can I upgrade only the webvpn portion to allow more licenses?
View 2 Replies View RelatedI'm using NAC 4.8, and I'd like to login using NAC Web Agent on Ipad. When I'm trying to do that, I'm receiving a message on Ipad that I need to install Java Plug-In, but there is no JavaPlug-in available for Ipad. Any additional configuration that I have to do on NAC Manager to be able to access the network using NAC Web Login on Ipad ?
View 3 Replies View Relatedi have in my network firewall ASA 5510 but the problem i cannot login to my firewall thru telnet or ssh even ASDM or bowser this is my configuration :
ASA Version 8.2(5)
!
hostname Amco-ASA
[Code].....
IPSEC VPN between 2851 routers. I have 4 routers 2 at each site using HSRP on the front and I need to encrypt traffic between. My concern is the failover portion.
View 2 Replies View RelatedI did an ISE 1.1.1 installation on a VMWare with ESX 5.0. After installation I am not able to login with my credentials(username admin, password XXXX) I can ping my ISE server after initial installation but I can not ping my ISE server after full installation.I did the installation several times and even did it on a VM with differrent VMversion.
View 3 Replies View RelatedMy college uses cyberoam for all network security. On windows i can successfully log into my account without any problem. But when I do the same on ubuntu(tried on various versions but failed!), the client returns "You are not allowed to login from this machine." I did the same thing as the instructions from the website said, but failed.
View 4 Replies View RelatedI have configured 3355 NAC appliances in HA pair everything is running fine.But not able to Login through GUI (Virtual IP) which is used during the configuration of HA pair.
View 1 Replies View RelatedI want to setup VLAN with the switches SG300 and SLM2024. What is the suggestion to connect these 2 switches. We have the Juniper net screen.
View 1 Replies View RelatedUsing AnyConnect Secure Mobility Client, logging into ASA5540. After I put my credentials in, I get the banner message (from group policies). After I accept that, I get another pop message stating:It looks like a pre-set message. Where can I disable and/or edit this message?
View 4 Replies View RelatedCan a layer 2 cisco 2950 switch be used as a dhcp server with it's own address pool.
View 3 Replies View RelatedI have a question if I Stack a Catalyst 3750 L3 with a Catalyst just L2, will we able to use all L3 capabilities?
Switches are
WS-C3750G-24TS-E1U
WS-C3750V2-24PS-S
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies View RelatedSo the other day at work we had a small power outage which shut off our server. Upon trying to turn it back on we realised we needed a password, but none of us can remember what it is at all. Our server does not have a brand and is running on windows 2003. We really need to get around this password issue, and there is no way that we can recover it (mostly because we are not getting the option to) When we turn on the server it stops on the typical black screen with white writing and lists:
Booting 'Debian GNU/Linux, with Linux 2.6.32-5-amd64'
Loading Linux 2.6.32-5-amd64...
Loading initial ramdisk...
Loading, please wait
[code]....
I just setup ACS 4.2 on windows 2008 standard server. I noticed that after a while, i could not launch the ACS from desktop. All services are up, i have restarted server a couple of times....The Program appears to launch and the disappears..
View 2 Replies View RelatedI want remove saved passwords in 2003 server with which XP clients login
View 1 Replies View RelatedI have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
Recently i had suffering with wireless connection problem, currently my wireless router connected to WAN directly, after that go into firewall and then go thru switch to end user PC, for LAN user there is no issue, but for wireless connected PC it is prompted with limited connectivity problem(DHCP is disable on router), after check with ipconfig /all. it seem likely due to wireless PC cannot get the IP from DHCP server. i am using DLink615 router. i had checked firewall setting there is firewall policy that connected all router ip into company LAN, but i don't think there is DHCP VPN setting up. is there anyway i can go thru firewall and get IP from DHCP server because if i set up DHCP on router, it cannot pass thru and access to LAN.
View 9 Replies View Related
