I'm using TP Link router. I went to DHCP reservation list and provided mac address of a computer and ip address to reserve the ip address for the computer. But it still not changing my current ip address. I rebooted router, rebotted computer, but it still not changing to the reserved ip.
View 3 RepliesI have a Blackberry Playbook and have come into a problem with it.I can't set a Static IP on it so would setting a DHCP Reservation in my Linksys E2500 router act as a static IP?
View 2 Replies View Relatedwhy my switch is not picking up a reserved address from the second pool below?console output with dhcp debugging on.ps. I have also tried 'hardware-address 0024.f769.bf40 1' which is hardware type 'other'
Config
ip dhcp excluded-address 172.23.23.1 172.23.23.49
!
ip dhcp pool main
import all
network 172.23.23.0 255.255.255.0
[code].....
I have simple set-up in my network with 2 routers connected to each other, 2nd router is just kind of wireless access point and switch to extend cable sockets upstairs.I have DHCP reservation on the first router and it works perfectly. Second router has DHCP server disabled, and I have configured DHCP reservation same as the first router, but it gives random IP addressess instead of reserved. how can I configure second router to obtain MAC DHCP RESERVATION TABLE from the 1st router?
View 7 Replies View RelatedEver since I updated my firmware to 1.01 my web interface for the network settings screen has been random. Somtimes it shows a DHCP reservation list, sometimes it doesn't. Sometimes there are reservations, sometimes there are selectable radio buttons. I guess I'm just trying to figure out if this is a firmware issue or not. Ever since I updated the firmware it has been flakey.... But I was having issues with other stuff before that. When there are no reservations, sometimes i can't even select any computers because there aren't any in the drop down, when all of my hardware is online?
View 6 Replies View RelatedIs it possible to set up DHCP server with reservations for specific IPs?
View 1 Replies View RelatedHow can I use the dhcp reservation with this router? I've network printer and i can't use it.
View 6 Replies View RelatedWhen I'm in Setup -> Basic Setup -> click on DHCP Reservation, I don't see all entries I've created earlier but computers that connect still have the correct IP address on the network; I don't know if I can create additional entries if nothing appears
When I go to Status -> Local Network -> DHCP Client Table the list is blank but some computers are connected to the networkI'm using firmware 1.0.01 build 10 Feb 21, 2011, language = English, Firefox 4.0.1.Rebooting the router doesn't change anything, I can't see connected LAN equipment and DHCP Reservation is empty despite the fact I've created entries.Together with the "Access Restriction" which doesn't allow to block a computer from 10pm => 8am unless you create 2 rules + various issues with attached USB + 2.4Ghz signal that is far from optimal (never able to achieve more than 144-N-Mbps) and I ask myself if I will not contact the store where I purchased this unit and ask a refund (and buy something else from another brand...)
I tried to enter a name that included an illegal character (in this case, a single quote), and it gave me the popup box that said I had done so. When the popup closed, my DHCP reservation table was emptied out (I had maybe 5-6 reserved clients). In fact, I can't add new reservations anymore at all from this screen as it lists nothing in the DHCP clients table at the top. (Note, there are plenty of things in the DHCP Clients table over on the Status->Local Network tab). At this point, I think that my pre-existing reservations are still being held, but I'm not sure as it's only been about an hour so nothing has renewed.
I had firmware 1.0.05 when I encountered this problem. I upgraded to 1.0.07 as a means of trying to kick it into action, but the problem still exists.
I've just got a WAG120N router and can't see anyway to see what devices are attached to the router or be able to assign static IP's
View 3 Replies View RelatedAll the SOHO routers I have used had a table which shows IP, MAC, Name, etc. In this table, I could easily put a check mark to a check box in a row that I would like to bind/reserve and IP would be reserved for that specific MAC.
In ISA570W, when I need to reserve/bind an IP to a MAC it asks me to fill out a table in which I have to manually type in the name, IP, and MAC.
Is there an easier way?Is there a way to do the reservation for multiple clients at once?If this is the only way, do I need to copy the mac address of each client somewhere and then reserve IPs for each one manually? This method looks very far from user friendly and efficient, unless there is a very logical reason that I cannot think of.
my researvation table is incomplete. Below I show ipconfig that shows wired & wireless NICs assigned ip addresses by the E3200 router but the DHCP table only shows one.
I need to reserve the ip address of the wired address but can't get at it.
I have Linksys E3000 Router and it is connected to 7 Devices at this moment via DHCP. I have got New NAS Enclousre (8th Device) which has got Lan port . I have connected Box to One free Port on E3000 Router. I see DHCP Reservation from 192.168.0.1 assging one IP to My NAS Enclosure Box i.e 192.168.0.13 But when i ping that box . It's not pingable. When i try to browse that NAS Enclosure's setup web page - it's not opening. I can access that box setup page if i connect direct 1:1 Lan cable over private network (169.254.XXX). It means web server is runing on box. I am clueless. E3000 is assigning IP to NAS Enclosure but can't Browse or Ping. I tried to Assign Manual IP address to NAS enclusure and reconnect to router. Still I can't ping or browse.
#arp -a show that box has IP. (Output from MAC os) .
? (192.168.0.13) at (incomplete) on en0 ifscope [ethernet]
Ping test from Router Page.
PING 192.162.0.13 (192.162.0.13): 32 data bytes
40 bytes from 192.162.0.13: icmp_seq=0 ttl=46 time=286.6 ms
40 bytes from 192.162.0.13: icmp_seq=1 ttl=46 time=290.2 ms
[code]....
Before upgrading my firmware on my EA2700, I can easily reserve IP address for my wired device. With the new cloud interface, I click to select the device from the top pane to bring it down in the reserved IP pane below. When I try to save the IP change I get two errors: 1) Invalid characters in the device name 2) Invalid IP address. I get the same errors even if I do not edid not edit the name or IP address.
As for the device name, I did not change anything or rename the device. One device has a " - " in the name and the router was happy with it until I tried to reserve the IP. Another one had a " ' " in the name, same problem again.
My network DHCP range is set to 192.168.1.200 to 192.168.1.250 and I use the range from 192.168.1.1 to 192.168.100 for static IP. When I tried to reserve a static IP below 192.168.1.200, the router say that is an invalid IP.
The workaround to this problem has been to temporary set the DHCP range to 192.168.1.1 to 192.168.1.50 and set the static IP in that range and rename the devices to a name that the EA2700 will accept. Next I move the DHCP range from 192.168.1.50 to 192.168.1.100 and repeat the process. After, all the static IP are assigned, then I can reset the DHCP range to 192.168.1.200 to 192.168.1.250.
This is a pain to do. In the previous (cloud less) version, this was a breeze to do. Also, I have not figured out how to redirect ports with the new interface. Is that progress?
i am having an annoying issue with my wrt400n and my foscam FI8918W. in the dhcp reservation tab, the wrt400n doesn't show the foscam anywhere in the tab. it shows all laptops, cell phones, nases, etc. if i use the cisco connect software it does show it in the network map. i can probably add it manually via the gui. is this something normal or security cams not considered devices?
View 1 Replies View RelatedE4200v2, firmware 2.1.39.145204
Router says "Invalid IP address" when I try to make a manual IP address reservation of the IP address range.
Example: local network 192.168.1.0/24, where .1 is a router, .2 is a reservation, .20-.50 is a range for DHCP.
Before upgrade I didn't have this problem.
I have the e4200 and I am having trouble getting DHCP reservation to work properly with my Windows 7 machines. Perhaps there is a step that I am missing. Basically I go to the DHCP reservation setup page, select my machine and add it to the reservation table. Then I save the changes. As soon as I do this my computer goes offline. If I reboot my machine, it is still offline. I've tried the same procedure to reserve the IP address for my phone and it works fine so I wonder if the problem is with Win7.
View 6 Replies View RelatedHow to check dhcp if not working
View 1 Replies View Relatedi'm having troubles with a DHCP server, which is unable to give IPs to hosts that are on a different VLAN than the server.I have this little scenario, one L3 switch (SGE2010-48 without PoE) with 7 different VLANs configured in[CODE]
View 3 Replies View RelatedI recently upgraded from a WRT54G and am having issues with a Win7 PC with wireless-N. Initially I had it configured static at 192.168.100.100 and everything worked, but the speeds were miserable (I followed all the forum posts and recommended settings). I noticed in the Status section of the router pages that the system showed up with the correct MAC address, but the IP showed as 192.168.100.10, which is the same as the router. Assuming this might be causing issues, I set a reservation for the system at .100 and set the client to use DHCP. However, now it won't pull an IP address at all. The status pages show the client with the correct MAC address, but an IP of 0.0.0.0. I've verified the MAC address a dozen times and rebooted the router and the client dozens of times with no change. Even when I removed the reservation, the system won't pick up an IP. I have a wireless-G client that's pulling an IP fine, so I know it's sort of working. The wired LAN is working fine, too. There are no IP conflicts, either. I changed DHCP to 'Always Broadcast (compatibility for some DHCP clients), but no change there, either. The client sees the network and still has a good signal, but just won't grab an IP.
I'm running Hardware Version: B1 / Firmware Version: 2.01NA
I have a Cisco 877W in place with an ADSL connection, which is working fine. However I cannot get it to hand out a DHCP address. If I associate with the AP over wireless then set a static IP I have full connectivity, similarly if I connect over Eth0 and set a static IP I have full connectivity. So it does just seem to be DHCP. Below shows my config... Any thoughts on the issue? Is it access-list related?I have checked with Wireshark and I see the DHCP request being sent out, but I don't see a DHCP offer being returned
View 4 Replies View RelatedMy team and I are having issues getting this configuration to work. We are using a 2811 Cisco router in class and the DHCP is not working. All other configurations for the other 2 routers are working but those were the easy ones. [code]
View 9 Replies View RelatedI've an 877W with four V LANS, All bridged (group) onto a BVI which is bonded to ATM etc for ADSL:
c870-advipservicesk9-mz.124-15.T5.bin"
1 is the backbone, and for the switch, and has DHCP running and working with no problems - x.y.1.z . Multicast is enabled so that various multimedia bits of kit can find each other.
2 is the "primary" WiFi, which has android devices as they cannot handle SSID not being broadcast or devices that can only do wep.(WiFi radio) it has DHCP, x.y.2.z which works fine. Multicast is enabled so that various multimedia bits of kit can find each other.
3 is a secondary WiFi for the kids, "hidden" ssid. They are fire walled so that bugs can't infect any other windows PC DHCP x.y.3.z.
4 Is a secondary WiFi for our laptops, "hidden" ssid .
For some reason, DHCP is not working on 4. it was working until the good lady of the house quizzed why her net was not working... I've concentrated on vlan4, as there are no "local" access-lists definitions to stop anything. I've enabled debug ip dhcp server, and can see requests serviced on Vlan2, but not on 4, I've enabled/re enabled encryption/ shields on Vlan4, but still can't see dhcp requests arriving and do not see them being stopped somewhere. I can see that the station authenticates OK, but if I connect the same laptop to v lan 02, requests pour in and are answered, proving it's maybe not a Microsoft problem.
Let me just say, I'm more or less self taught with the the net, no real mentoring, so 'think' I have the general idea of the different layers, access-lists etc. so this config is probably not ideal, but it works.
version 12.4
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
[code]....
I am trying to configure the DMZ on my SA520 router but without success.After a lot of tests I reduced everything to a very simple test case that is not working: I setted the "Optional Port Mode" to "DMZ" and enabled "DHCP Server" in the "DMZ Configuration", but DHCP on the DMZ does not assign any address.I am wondering if my optional port is broken or not.
View 4 Replies View RelatedI have a Cisco IE-3000-8TC running 15.0(2) EY1 IES-IPSERVICESK9-M. I am trying to configure the switch to auto configuration (download only the configuration file and not the software image) via DHCP from a combination DHCP/TFTP server. When I configure the switch with the commands (on initial configuration): Code...
View 1 Replies View RelatedI have a RVS4000 witch I use as router, and DHCP server. I have a WAP321 witch I have configured SSID with one VLAN. Both devices have fixed IP address. I can connect computer to the wifi access point. But the computer cannot get an IP address from the DHCP server of the RVS4000. If I set the IP configuration manually, it can get an access to the network and Internet.
With another wifi access point it works, the computer get an IP address for the DHCP.
What should I have to do to make my DHCP server works with my wifi access point ?
We have a single SGE2010 in layer 3 mode switch with a Server 2008 DHCP server.
We will be implimenting a Voip netowork where the PC's connect to the voip phone. I would like to create another vlan - 10. I have created the vlan and assigned the IP on the swtich.
Routing seems to be working. I can ping both IP addresses of the switch on either vlan.
I cannot get DHCP working. In the SGE switch I have enabled DHCP Relay, enabled option 82, set my DHCP Interface as VLan1, and specified the DHCP servers IP address. On the ports I have set the port where the DHCP server connects to as a trunk port with Vlan 1 untagged and vlan 10 tagged. I have set the ports where the phones connect as a trunk port with vlan1 untagged and vlan 10 tagged.
User connects through a sonicwall device via SSL VPN and gets a static IP every time, despite what device they come from.
1. LDAP somehow supplies the IP from a DHCP server behind the sonicwall
2. The sonicwall somehow supplies the static IP on the interface that the net extender is connected to.
Two people went on a business trip with their laptop and when they came back they could no longer access the data server. Cannot map the network drive either.
1. Every desktop PC in office can see and access the data server fine.
2. We have a DHCP and DNS server (on one PC; Windows Server 2008), but we had to shut down the services because internet and email didn't work when the DHCP and DNS server service was on. I am confident that this is due to the recent shutdown of the company e-mail server (now outsourced) and the server settings needs to be reconfigured. The described symptom persists even when the DNS server service is stopped.
3. Upon taking a closer look at the DHCP reservation settings. The reservation status indicates as "Reservation (inactive)". I don't know the MAC address of the device, so I have no idea if the values are correct. Tried rebooting the server, delete and recreate the reservation, reboot router; no cigar.
4. Using the coworker's laptop, the data server is shown in the "Other devices" section even with the DHCP sever disabled, but shows error that it cannot access it.
5. All users, with the exception of the data server, have dynamic IPs assigned.
6. DHCP, DNS server is set to 10.10.10.2, Router is set to 10.10.1, Data server is set to 10.10.10.175. 10.10.10.2 is also an accounting server which can be accessed by everyone even in the midst of this mess.
I have a new 5508 that I am setting up. My first one from scratch.
Interfaces:
managment -> 10.10.10.10 ->dhcp 10.10.10.1
voice -> 10.10.7.1 ->dhcp 10.10.10.1
guest -> 192.168.1.2 ->dhcp 192.168.1.2
Local DHCP (via the 5508) is for the guest network while the management and voice use the Windows DHCP server.
My problem, Voice and guest work fine. I have two SSID's (one 802.1X and the other PSK) that use the management interface that will not get an IP. I have enabled dhcp proxy from the cli on the controller. I tried with the management VLAN tagged and untagged.
setup a DHCP server on a WLC 2504. I'll try to resume my configuration:
I have 2 networks: inside users (vlan 1) and external users (vlan)
My controller uses the port 1 to connect to the switch, which has a trunk with WLC.
I have two routers, one using vlan 1 (192.168.3.0/24) and one using vlan 10 (200.X.X.X). All ports to these routers are access ports on their respective vlans.
I have 2 SSID, one for inside, other to outside. Inside is working very well.
To the outside I created a DHCP escope and already set the IP of the management interface 192.168.3.119.
Managemente interface (vlan 1 inside): 192.168.3.119/24
Outside interface (vlan 10): 200.X.X.195 - Default gateway 200.X.X.X.193
I alredy checked the DHCP Proxy in Advanced option.
See the output of the debug client:
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
[Code].....
I'm having troubles with this firmware in a SG300-28 switch. Actually the DHCP server, a new feature in this firmware release, doesn't work correctly. DHCP static reservations are not working: CLient ID and MAC address are not recognized correctly, and the DHCP server assigns the first free IP in the pool, rather than the reserved one.If Cisco engineers read this, plese correct the issue.
View 5 Replies View RelatedI seem to be having a problem with DNS name resolution after configuring my router (Cisco 3725 running IOS image: c3725-adventerprisek9-mz.124-25.bin) for handling DHCP requests.
Before I made the change, everything was working correctly; I could ping Google.com from a computer inside my LAN and would get response from one of Google's public IP's like normal.
I had a separate DHCP/DNS server running Windows Server 2008 handling the DHCP request and DNS queries.
When I made the change, I turned off the DHCP/DNS server and issued the following DHCP commands to my router:
Code...