this has been a new developing problem i have been having it its starting to be a pain in the you know what. Recently i have been losing connection off the network countless times a day then to have problems getting back online. I have a Belkin Surf and Share Wireless N router that was working perfectly. i have a laptop sitting next to me that doesnt go offline when i do. Seems like im the only person in the house hold experiencing problems. I even tried a different wireless card and still have the same issue. im clueless on what to do. i tried flushing my DNS several times. I have a connection of only .30 mbsp from this issue as well.
I am experiencing a great inconvenience with my relatively new Belkin Surf+ N300 wireless ADSL router.I am confident that the router has been doing this since I got it, however I have not noticed until now. Whenever I try to access a URL with the word "router" anywhere in it (e.g url...) it will take me to my router's settings page (usually comes up when the router's LAN IP is entered)Yes this is very handy if you don't know the LAN IP, or are less skilled in router management, however if, like in my case, you like to access websites with "router" in their URL, you have a serious problem. I have tried factory resets, and have scoured through the settings of the router but have been so far unsuccessful.
I have replaced my father's wired modem (he's with [url]... in the UK) with a Belkin Surf+ (F7D2301uk) router running firmware version 1.00.16. When he tries to access the network from his Tosh C660 Win 7 Home Premium, 64bit laptop the network connection between the laptop & router disconnects after a minute or so. The only way to reestablish a connection is to Disconnect and Connect again in the Wireless Network section of Networking panel. But here's the weird bit. My own Mac Book keeps connected fine without any problems as does my Sony Ericsson X10 phone.
I connected a Belkin Surf N300 Wireless N Modem-Router have been trying 2 weeks to get it to work wirelessly, The icon for Belkin bottom right side of screen says "Connected to the belkin router via ethernet cable, and if I click the icon for computer connection info it says "Unidentified network (Belkin) Acess: Local Only.) I can use the internet while I have the ethernet cable attached to computer and using wired broadband, but once I take out cable I lose all connection. Have been in touch with Belkin by phone for 4 hours, they replaced unit but still can't get the wireless internet, the wireless is turned on(WAN & Bluetooth are turned on)
I am using a Belkin Surf wireless modem/router with this computer (Vista) no problems at all.When I boot up my HTPC (Windows 7) all is fine until it tries to connect with the Belkin Surf. Then its Blue Screen of Death and no joy. If I turn off the modem, the HTPC boots up perfectly normally. Turn the modem on and as soon as I try to recognise the home network, it crashes again.
If the Belkin Surf N300 (Model No F9J1002v1) is CN21/ADSL2 compatible? It doesn't mention it on the box and try as I may I can't get through to tech support UK as I keep getting cut off and the J model router is not recognized on the UK website only the K
Windows cannot open this file (the update). what program opens the update? I just bought a SURF N300 v F7D6301 and am trying to install the update on the website, but I just get a box that says windows cannot open this file.. what program do i need to tell it to use to open the update?
We have 12 PC connected through a Switch(D-Link 10/100 mbps) with Configtured with Manual IP Address. the IP address range is 192.168.1.1 subnet mask 255.255.0.0 default gateway 192.168.1.1.Internet Cable Connected from Modem to Switch Directly & all the computer access internet by filling DNS with 202.56.224.153 other 59.144.127.17, We fill this DNS only where we want Internet access allowed by limiting that pc with Limited User access. How to configure Belkin Surf N300 Router with this network.
I have a belkin surf n300 usb wireless N micro adapter. No problems installing this adapter on a HP Desktop running windows 7. I have tried to install on a gateway laptop also running windows y 64 bit. In device manager it show that the product is working. It will not connect to any network. The adapter is an F7D2102 az ver. 2011az
I'am having problems when connecting to the internet. I'am running Win7 64-bit and i have Belkin USB wireless adapter( Belkin surf N150) When i first bought the adapter it didnt connect to internet, so i though it is not working and i got it replaced. I got the same problem with the second one as well, and then i have changed the wireless mode on the device manager from: IEEE 802.11b/g/n to: IEEE 802.11b and eventually i have connected to internet without any errors, but in this mode the internet is unbelievably slow which is very slow when compared to another wireless mode where i have changed it from. So my question is why i can't connect to internet IEEE 802.11b/g/n in this mode? The weird thing is that some times it connects to internet with no error and dissconnects again in a short while. Also when the windows tries to repair it, i get this report:
Windows Network Diagnostics Publisher details
Issues found Problem with wireless adapter or access pointProblem with wireless adapter or access point Not fixed Refer to Windows Help and Support for more information about wireless connectivity problems Failed Reset the wireless adapter Completed Investigate router or access point issues Completed
I have actually made my laptop a hotspot for example i have cable network connected on it or usb internet and i am using connectify software to share internet through wirelesss card it is sharing through wireless card to mobile and other wireless devices.. But only the issue is i want to set bandwidth for every user or default bandwidth rule for every device connect.. connectify showing me every user that connect internet through my laptop but it has no bandwidth setting option is there any solution to set bandwidth as per user or default bandwidth then whoever connect he will get my selected speed.
I have a Canon i6700d, which I connect to the belkin N600 USB port to share on the network. Driver for the printer is installed. From the belkin router monitor, the printer is listed under "Networked USB devices". However, the printer is grayed out and can not be selected. the dialog complains that the printer is not available.
Verizon FIOS fiber optic DSL router 100meg working with other desk top and two other computers. The IP address is correct and signal is real strong, excelent according to PC. I put in the security KEY and it connects and says it's ok but no internet.I've tried every thing. When I plug in the ethernet cable everything works fine on line. With Belkin you can let windows start the wireless input or Belkin. I tried both. No luck. I'm sending you this over my ethernet cable. Need Tech support.I have another desktop with Belkin wireless card and it is working fine . I did try to troubleshoot useing it and lost internet on it and had to do a restore to get it back. So afraid to mess with it.
today my Belkin 7050 wifi adapter arrived.I went through the install procedure from the cd,and when asked to plug in the adapter,I got the message asking for a notebook card,which I haven't got.It then told me that the drivers aren't installed.The device isn't showing in device manager.I called Belkin support but all the could suggest was that the device was to try it in another computer.I am unable to do this because the communal computer needs administrator rights to install programs etc.
I recently updated to Windows 8, and before updating, Windows 8 setup recognized the drivers for my Belkin G Desktop wireless card. After installation, my system was able to connect to my wi-fi network without any problem. However, due to the power going off at my home, an automatic update on Windows 8 got interrupted.
Since then, it has caused a ton of problems, which caused me to finally re-install Windows 8. Now, however, it does not recognize the wireless card and its drivers, and does not let me install from the CD, or through any alternate sources ?
Having the same problem with a Dell Inspiron Laptop using a belkin pcmcia wireless card. It was working, but has stopped doing so. I was missing some network adapters which I have reinstalled, and the hard wired connection is now working again, but wireless will not get past the acquiring network address phase. I tried the ipconfig /all and it shows my IP address as 0.0.0.0 and the same on the subnet mask. it says the autoconfig is enabled and dhcp is enabled. My HP laptop is connecting to the wireless network just fine.
I just recently had comcast high-speed cable installed, and purchased a Linksys E2500 advanced dual-band N router to get myself going. I'm running an Asus G74s series laptop with windows 7 and everything runs great while I am the only one connected.That being said when another laptop connects (Toshiba satellite also windows 7) the internet stays stable. It isn't until we try and do something that the internet randomly disconnects for 2 or more seconds before re-connecting and putting us in a constant loop of idiotic disconnection.
A quick example would be using the Toshiba to connect to World of Warcraft, I on my Asus can surf the web just fine for about an hour before it disconnects. When I try connecting to a, or the game at the same time it'll allow play for about 7 mins before the net drops for a few seconds then re-connects. This happens frequently no matter the time of day.I have attempted re-setting everything. Everything is up to date including the router. I've attempted to release and renew my IP. However I get this :
Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved.
I am not good at networking. My friend wanted me to set up his home network.because the modem is unable to supply a good wireless connection to the rest of the household when the door is closed, a second router was needed.I set both routers to run with DHCP as they have many devices that needs to connect to the router for internet. However, a few hours after setting it up, my friend's pc as well as all devices connected to the second router faced issues. The router's interface showed that it does not have connection to the internet. they are still facing this problem until now.
I thought I had this problem fixed i.e.unticking `allow computer to turn this device off to save power`in Wireless Connection Properties, I still have the problem the diagnostics say I did not receive any response from the wireless router or access point! I have Vista SP2.
I woke up this morning to find that I cannot surf the web anymore. I was able to last night just fine. My set up is this: Verizon Fios router(192.168.1.1)> Netgear gigabit switch> SMC router smcwbr14s-n3 (192.168.1.201) the Fios router is has a build in wireless but is in another building and i am not within range of it. I have a cat 5 cable that run between 2 house's... the cable comes into my house and into my switch then to my SMC router (smcwbr14s-n3 ) that is running in bridged mode to function as an AP. I can connect to a lan port on the switch or router and connect to the web (im currently in a lan port now.) Here's the thing, I can still connect to the wireless, it's just so slow (1Mbs -6Mbs)that i am unable to get anywhere... I do have security setup (WPA2) an im going to kill that to see if it resolves the issue... but it has been working fine with the current security setting for the last 5 months, so i dont really thing that is the issue.
my TWC connection and I can surf the net everywhere but when he takes it to his home and connects through his DSL he can pull up Google and can even search through Google but he cannot go to yahoo.com or Aol.com. Malwarebytes comes up with no infected files. I did a restore and the same problem. I did a recover! And same problem. I pulled up a Cmd window and run an ipconfig. I am used to seeing a 192.168.x.x address but on his I get a 10,x,x,x number.
I set up my D-Link DIR601 and set the password for the internet, though I can't surf on the internet. but I can connect, like it says im connected but it won't allow to surf.
Here is my internet setup:Blue Zoom ISP (Satellite) >>> Their Modem >>> Sony Viao Desktop >>> Linksys EA4500 Router,I have a metal garage with an apartment in it about 30 feet from the house. I cannot get any kind of wireless internet into the apartment because it is made of metal. I barely have cell phone signal.So, in order to get internet into the apartment I have a Ubiquiti Nano Bridge mounted about three feet off the ground right outside of the apartment which runs a CAT 5 Ethernet cable inside the apartment into a Linksys EA2500 Router.
My network connection keeps on disconnecting every few minutes and my downloads are always interrupted. I also checked out my Ipconfig and the Media State says Media Disconnected. I�m using windows XP by the way.
