I recently bought and installed Windows 8 Pro and figured that there are no drivers available for the WMP54G Wireless Network Adapter (version 4.1)on this OS. What is the solution?
View 4 RepliesI had an antenna break on a WMP54g v 4.1 and I was able to replace it with a WMP54g v 4 but I'm not having a lot of luck getting the driver to install. This is on Win7 32 bit Home Premium. I assume this is due to the fact that I was using a newer and switched to an older piece of hardware and there is some driver issues. How to uninstall the old driver completely so I can start fresh I have tried everything I know to do and can't seem to get anywhere.
View 1 Replies View RelatedWhere I can find a driver for:WMP54g v2 for Vista SP2 32bit It used to work just fine, until I recently reinstalled Vista (and installed all the updates) and now my internet connection is "limited." This means that it connects, but is extremely slow and the connection goes in and out.Here are some random notes about my problem:
Nothing is disabled, there are not any conflicts, and the problem remains even if I restore the OS back to restore point that I created right after reinstalling Vista (and before doing anything else).If I hook the computer directly up to my netgear router via cable, Windows Update will download and install a more recent version of said driver (no improvement).Other laptops in the house have no problems with the wifi. I have turned off both my cable modem and wifi router several times.The adapter does connect to the internet, and the signal strength is "excellent", but if drill down to the properties of the connection, it says that IPV4 is connected to the internet, but IPV6 is "limited." This then results in a very weak connection to the internet that goes in and out. I have tried unchecking IPV6 per some recommendations, but that did not work. I have tried resetting everything (winsock, etc) via command prompt. Firewall is off, no antivirus software
I am having trouble locating and installing my pci receiver card driver using windows 7 64 bit op sys
View 1 Replies View RelatedTrying to install WMP54G v4.0 on XP SP3. I have tried all three PCI slots. Removing driver RT2500.SYS system will boot. Put it back and BSOD Error:driver_irql_not_less_or_equal
View 8 Replies View Relatedmaking Windows 7 do what it's supposed to? Seriously, there needs to be a button you can click to roll it completely back to XP.
View 1 Replies View RelatedI installed Windows 7 Ultimate on my computer, and I cannot get my Linksys to work on it, the light doesn't light but it shows up in device manager. I've tried using Vista 32-bit drivers but it doesn't work at all, I am thinking it isn't a driver issue at all because it shows that the driver is up to date.
View 1 Replies View RelatedI just bought this wireless g pci card and installed the software from the cd on to a windows 2000 pc. When I went to run the software I can only click on the exit button. I looked on the forums and saw that for win 2000 you should only install the drivers by allowing your computer to detect the card. I uninstalled the software but my computer wont detect the card now and if I reinstall the software I cant even open it up anymore. The card is not listed in the device manager at all. Would installing i the first time have created anything in the registry that would have been left behind in the uninstall and would it be blocking the computer from detecting this as new hardware?
View 9 Replies View RelatedI installed the Linksys WMP54G wireless adapter card in my windows 98 SE computer before I installed the software. (I now know the software is supposed to be installed before the hardware is installed.) The software didn't work. It wouldn't connect to any network. (I have used this adapter card and software before, so I know how to get it to connect when it is working properly.)I used the uninstall to uninstall it, but it didn't work. It removed most of the files, but in the "program add/remove" window (in control panel), the Linksys software is still listed. Using "program add/remove" to try to remove the Linksys software also doesn't work. It acts as if it is removing the software and then shows a message that says the software is 100% removed, but, after rebooting, the software is still listed in the "program add/remove" list. The WMP54G CD won't reinstall the software. Instead it says the software is already installed. How to find whatever WMP54G software file(s) are left on my computer and tell me how to manually remove them.
View 1 Replies View RelatedI'm trying to install a WMP54G PCI Version 4.1 in my Windows 2000 Pro SP4 computer. I ran the setup cd before installing the card, then took out the disk. After installing the card and powering the computer, the Available Wireless Network screen didn't appear. I also didn't get the Network Monitor icon on the taskbar. Network Monitor appears in the start menu, but can't be started. Device Manager says the card is working properly and there are no conflicts.
I uninstalled the software, removed the card, and repeated the installation process with the same end result. The card light blinks like it is receiving data. I'm using a Linksys WRT54G2 router. Both my desktop (W7) and my laptop (Vista) connect just fine. How can I get my W2K computer on the network?
I got the D-Link router setup and with the network key. When i tried to type the network key in my pc(which has the adapter). it gave me an error.Network key password need to be 40 bits or 104 bit depend on network configuration. This can be 5 or 13 ascii characters or 10 or 26 hexadecimal characters". what does it mean? because the network key work with other pc..but not my pc with WMP 54G. reason?
View 3 Replies View RelatedI have the WMP54G internal wireless adaptor. It normally works fine, but I have been having problems with it lately when I turn my computer back on from sleep. Even thought the wireless router works just fine, when the computer wakes up from sleep the adaptor does not seem to detect any network. I have to restart my computer, and then the adaptor detects the network.
View 1 Replies View RelatedI'm having an issue with a 2 week old WMP54G pci adapter. The behavior is as follows: I get a successful connection and excellent speeds, but every 10 seconds it stops transmitting and drops off the network for a moment. Then everything comes right back. 10 seconds on, drop, 10 seconds on, drop.I've investigated possible sources of interference, but there aren't any strong networks coming though on the same or nearby channels. Moreover, other devices sitting in essentially the same spot are connected consistently and show no variation in the signal strength.
Other info: OS is Ubuntu 10.10, the machine is a Dell GX270.
Here is my answer to the lack of support from Cisco:
[URL] I am presently using this driver to connect.
Are there any updated drivers for the AE1200 on windows 8? in win 8, I'm no seeing both bands - only 2.4Ghz and I'm only connecting at 54Mhz.
The disc that came with it has V5.100.68.46 which seem to be the lastest on the support site.
I have been looking for 4 hours now for this driver.. Where to find it, that would make my day so much better
View 1 Replies View RelatedI don't know how to install this driver - I didn't see a .exe file or a "setup" icon
View 9 Replies View RelatedI am trying to update the driver for my WMP300N for Windows 7. I get a message from windows telling me that a registry key does not exsist. Is there a way to create the proper registry key or get a download that will update the registry? The download from linksys does not update the registry or create the key.
rdrussellCompTIA A+ 2007MCSE Windows 2003
I have an E1000 router and have updated the firmware to v2.1.02 Build 6. Also have the AE1000 Wireless-N Adapter and wanted to see if there were any new updates. According to this Linksys page the latest driver is Ver.3.1.12.0 (04/27/2012). I have downloaded the file and unzipped it to the desktop.
I am running Win 7 64-Bit so I opened this folder: C:UsersJOHNDesktopAE1000_Win7_3.1.12.0-WHQLWin7_64_v3.1.12.0
Which file will actually install the new driver:
netr28ux Security Catalog 9 kb; netr28ux Setup Info 11 kb; netr28ux.sys System File 1,563 kb; RaCoInst.dat DAT File 14 kb; RaCoInstx.dll Application Extension 320 kb
I just installed windows 7 on my wifes new com and the device couldn't detect any connections using the default drivers (windows called it an nvidia wireless network card). I downloaded the drivers put them on her hd via flash drive and attempted to update the device drivers through the device manager but it says the drivers are already up to date. I uninstalled the device and windows called the device MCF-J415W and when I tried to update the drivers again it said the drivers were not correct. I'm not sure what is going on here and why linksys doesn't just have a .exe driver installer. I've had the same issue with my wife's computer when it had win xp except it didn't have any generic drivers to install. Also I tried selecting the driver from the list of pre-loaded drivers and found one for the exact device but it would not install those either.
View 2 Replies View RelatedI'm looking after any driver wich can operate the WUSB600N v2 under Windows 98 at an old computer who is not able to operate with WinXP.Is any "freak" there who knows wich driver can be used for it? (Perhaps as well an older driver from any other older CISCO wlan stick ... ?)
View 2 Replies View RelatedI need the Windows XP WUSB54GC V.3 Driver!
All of the other threads on this forum have expired links to the driver. Where can I find it? I've looked for hours & the cisco website offers nothing for Windows XP for WUSB54GC Version 3
I recently re-installed Windows on my PC, and I had the Wireless-G PCI Adapter installed before I done the re-installation.Now I've re-installed Windows, the adapter doesn't work. Do I have to re-do the whole process again? Also, I didn't actually install it myself, so any detailed step-by-step tutorial?
View 3 Replies View RelatedI am having some trouble getting my computer with Windows XP to use the Linksys model WMP54G wireless - G PCI adapter to connect to the network in my house. I have installed the hardware and the drivers. When I open the view available wireless networks window my network shows up with two bars of strength. But when I select this network and click connect, I get an error message saying "Windows is unable to connect to the selected network. The network may no longer be in range. Please refresh the list of available networks, and try to connect again." I have other computers connecting to this wireless network without any problem. The wireless router I am using is the model WRT150N wireless
View 6 Replies View RelatedMy router is located in my living room and my desktop is in a room located some 30 fett away with several walls in between. I am a light user (surf internet, read emails) and I do not have any special requirements.My router is a WRT54G router and my Wireless-G PCI Adapter is a WMP54G. Both have worked well for the last 5 years or so. Unfortunately, I had some work done in my room and the workers have broken the antenna on my desktop PCI adapter.What should I buy to replace my WMP54G?Should I get a PCI adapter or an USB adapter? Which one?Reliability, range and ease of use are my priorities. Price is not a major concern.
View 1 Replies View RelatedI installed Windows 7 on my HP Pavillion assuming I could re-download a driver for my Linksys Wireless Adaptor Card discouvering that was not a good move. Any short cut/trick for getting a Windows 7 Driver for Linksys Wireless-G 2.4 PCI Adapter Model No VMP54G Wireless Monitor?
View 5 Replies View RelatedThe last update was the following. 03/31/2010 Ver.3.0.10.0 Here we are well over a year later and no update at all. What is going on?
View 4 Replies View RelatedI have the above mentioned WMP54GS. And I just got a Windows 7 capable computer and got it installed. Now I can't find a driver that will work at all. Other than the Broadcom drivers that Windows installs naturally. (The Broadcom drivers are terrible. I play World of Warcraft and when before on my old Vista 64-Bit system I would get around 50 to 60 MS I now get 180 to 200. ) How to get this to work.
View 9 Replies View RelatedI have the PCI adapter installed on my computer. I have installed the driver and my computer recognizes the adapter, can see the network I want to connect to... but will NOT connect.I have 9 other wireless devices connected with no issues. But the PCI adapter will not work.
View 1 Replies View RelatedI have a wireless adapter WMP54G for a long time, but recently i updated to windows 7 and the problems begun.
After read a lot of stuffs about this problem, i downloaded a driver by RALINK and installed de adpter. But......on the installation, show two hardware: one is the adapter Linksys WMP54G...and the other can't be installed. So..on the Device manager appear like "unknown device" on the three of "USB controllers"
So...i'm already try a lot of things and can't install this adapter
I'm trying to install dis wireless network adapter in a computer with a W98SE OS.
I try some drivers, but dowsn't work. Information or the drivers for this network adapter for W98??
i need software drive linksys wmp54g for windows 2008 server
View 2 Replies View RelatedI can't create a network bridge in windows xp or well i can, but then my wusb600n says it is not connected, it can find networks but it wont connect to them? I tried take out the lan cable and create but with same result, is this normal that this adapter can't handle network bridge? If i make a virtual machine in Virtualbox i can use the internet, but i cant when i create a network bridge connection in windows xp..
View 5 Replies View Related