Linksys Wireless Router :: E2500 Can't Connect To Continue Configuration
Sep 17, 2011
I have a Cisco e2500 and I want to extend my network by connecting my old Linkysys G router to it. Â There are plenty of instructions on the net, and I get all the up to providing a new IP to the second (old) router. Â As soon as I give it a new IP, I can't connect to it to continue the configuration!For instance, when I change the IP from 192. 168. 1.1 to 192.168.1.2 on the second router, I cant get my browser to hit it and open and admin page. Â I tried a bunch of values in the last part of the IP, and none work.
View 1 Replies
ADVERTISEMENT
Jan 9, 2012
Got a problem with my new Linksys E2500 router. I have a Huawei Smart Ax MT882 cable modem, that connects to my desktop through an Ethernet cable, it works fine.
Recently i bought a notebook and i thought i could have a wireless connection, using the modem as well... So I bought a E2500 router, that is connected with Ethernet cables to the desktop and the Smart Ax MT882 modem.
It happens that i am not able to setup the configurations to make this work (This router does not supported by my ISP provider).
View 9 Replies
View Related
May 3, 2012
can't connect all my devices like an Iphone, Nook or another computed to the wireless network with the e2500, we have three devices but the others can't connect.
View 3 Replies
View Related
Jul 31, 2011
I install the E2500 router with my modem. it works fine with other compaq desktop and gateway laptop. But the HP Pavilion dv6910 can not get online. I try my hp laptop at starbuck shop, and it work fine.
View 3 Replies
View Related
May 9, 2012
I have an old Speedstream 5100 modem hooked to my e2500 router. Everything works well except if for some reason my modem disconnects from ISP I can not log into it through the route to reconnect it. I must plug a direct cable into modem from computer run connect script then plug modem back into router all is fine again.
Â
why connecting to modem through router is blocked?
View 9 Replies
View Related
Jan 19, 2012
Is it possible to connect my WAP54G to my new E2500 router?
Â
I previously had a WRT54G and had my WAP54G connected to it in AP Client mode. Â This enabled me to have internet access on my desktop computer that is located in another room downstairs.
View 2 Replies
View Related
Aug 1, 2012
I installed an e2500 to my cable modem and everything went perfect. Then 2 weeks later the electricity went off for some power company upgrades. when the power came back on the modem wouldnt connect. I have been through every solution in the cisco articles. The computer connects when directly wired to the modem, so I know there is signal. When I place the router into service and use the ethernet connection the modem no longer displays the active internet led. The e2500 ethernet led to the computer lights and the power led. The Ethernet led from the modem to the router doesn't light. I did a complete reset on the router. The setup software only runs to 75% complete then stops and tells me to check the plugs. Ive checked, replaced and swapped the cables. I've set the MAC to clone, and verified the MAC address via ipconfig. Ive done the complete powercycle at least 20 times.
View 3 Replies
View Related
Jun 27, 2012
I've found a few people with this problem on the internet. I'm using my phat 360 with the black N adapter. e2500 is updated to the latest firmware. But my 360 cannot connect to the 5ghz N, only 2.4ghz g. The wierd thing is that the 5ghz signal gives a better signal than the 2.4ghz.
Â
I just found a thread on google talking about the e4200 and someone mentioned counterfit adapters and problems with them. I did buy this on ebay for a cheap price, so it looks like it was too good to be true. this is a counterfit? It does have a real hologram on it.
[URL]
If this is real, what else could be the problem. Has the firmware not been updated to support the 360?
View 6 Replies
View Related
May 14, 2013
What should i do ?  Reset  ?  How  ? maybee i did not  set the cable properly  ( what is an ethernet cable ? ) the one i have is a short cable with what looks like telephone jacks at either ends.  one end is plugged in my comcast modem and the other into my mini mac.
View 1 Replies
View Related
Dec 21, 2012
How do I connect a sling box to this router/
View 1 Replies
View Related
Jul 4, 2012
I just bought an E2500 router. I have until now been using a Netgear DG834G v5.
Â
I have tried multiple times but my success has been limited. I turned off DHCP in the Netgear, set the isp login question to no, and set it into bridge mode. I managed to use Cisco Connect to connect the Netgear and the E2500, but there was no internet.
Â
I logged into the E2500 and entered by ISP details in the PPPOE section. I went to status and clicked connect, but a message would eventually pop up saying that an IP address could not be found. In the Netgear I could set up VPI and VCI etc manually, but can't find those settings in the E2500. My ISP also requires a dynamic IP - does this mean that DHCP must be off in both the Netgear and the E2500?
Â
 I factory reset the E2500 and tried Cisco Connect again, but it said that it couldn't find the device.
View 1 Replies
View Related
Apr 21, 2012
I can't connect to my setup page [url]... I get to the page that says..."There is a problem with this website's security certificate." Then I click the "continue to this website (not recommended). After this it will not connectÂ
Â
Tried with IE9 and Firefox 11
Â
Firefox says "The connection to the server was reset while the page was loading."
Â
Internet still works. PC is connected directly to router. Tried different port on router. Tried installing CiscoConnect.E2500.1.4.11299.0,0, but it fails saying there is no router connected to PC. Like I said I am on the PC now, wired to router and have internet access via cable modem connected to router. I can see my ireless printer on the network also..
View 2 Replies
View Related
Dec 23, 2011
Ok group here's the issue. I have a E2500 router with a wired connection for my sons xbox and 2 laptops connected to it. The laptop I used to set-up the system will usually connect to the router but not allow me through to the internet then after a shutdown and repowering it connects. what to check? The othhitch. Both arer laptop connects without a e running vista home.
View 2 Replies
View Related
Jan 2, 2012
Switched from a Netgear router to a Cisco E2500 and now my Samsung blue ray won't connect to internet.
Â
It says physical connection established but can't connect to external network.
View 2 Replies
View Related
Apr 24, 2012
When I try to connect new iPhone 4S, it goes to the page for all the info (IP address, etc.) instead of just asking for the password input. I've tried disconnecting router and restarting, plugging iPhone into iMac laptop, etc. (PC is hardwired into server and PC laptop, iMac laptop and former iPhone 3 all connected to wifi w/o difficulty.) Went to site of purchase (12/2011) of Lynksys E2500. They suggested might need to download a driver.how to locate and install updates to driver for E2500 to allow connection to iPhone 4S?
View 2 Replies
View Related
Oct 16, 2012
I have AT&T Uverse which provides Internet for my home. The wireless capability of this router is pretty bad, I don't get good/reliable wireless reception upstairs in my office. The solution was to buy a Cisco E2500 and add it as an access point upstairs.
Â
I have the E2500 LAN port connected to the LAN port of my uverse router downstairs. DHCP is turned off on the E2500. I have my office PC wired into the E2500. The home PC works fine, its getting DHCP from the uverse router downstairs and connects and good speeds. The problem comes with my wireless devices trying to connect to the E2500.Â
Â
I should mention that yesterday when i bought this, all worked fine. This morning when I came into my office none of the wireless devices would connect to the E2500 at all.  But as soon as I remove the cable that connects the E2500 to the uverse router downstairs they will connect via wireless but of course not get an IP address since that is disabled.
Â
I have factory reset the E2500 and uverse router several times and am getting no where. what could be causing the wireless devices to not connect at all?
View 8 Replies
View Related
May 28, 2011
It used to work, but just stopped. We have tried to reeinstall but it won't recognize the adapter. I cant click the next button to continue installation. I have changed USB ports and restarted the computer. I have unstalled Norton 360. But it still won't install.Â
View 3 Replies
View Related
Mar 6, 2012
what user name do I use to access the E2500 configuration panel. I have used the computer name, adm, adim, and the router default password and I canot log on to the configuration panel.
View 1 Replies
View Related
Aug 12, 2012
I set up a basic Linksys E2500 with the following information and connected to the internet straight away without a problem: I have spent several hours simply trying to get this basic information into the Cisco 819 using CP Express without success, i.e. I get no internet. Rather than show my inputs, What is the correct setup. I am a novice so I'd rather solve this issue using CP Express just to get connected in the first instance. I have a static IP address, I connected the ethernet cable carrying the internet to the internet port of the E2500 and an ethernet cable from one of the ethernet ports of the E2500 to my PC. For the 819, I connected the internet cable to the GE WAN 0 port and the PC to one of the FE ports.
View 18 Replies
View Related
Apr 13, 2013
I cant get it to connect to internet, it keeps giving me an error message. I have windows 7 and Linksys WiFi Router E2500
View 1 Replies
View Related
Jul 9, 2012
I've bought the EA4500 and configured it to connect to internet. it works fine.however, one day after it, it can't connect to the internet anymore. I go to the router setup page and try to manually connect it to the internet, but it keeps "connecting." I then restore to its factory configuration, then do the configuration again and it can successfully connect to the internet.however, one day after it, again, it can't connect to the internet anymore.
View 2 Replies
View Related
Jan 26, 2012
Using the quick set up of DIR-600 from the CD, I encounter this message:"Your new router does not appear to be connected properly.Follow these steps:
1)Make sure that your are connecting your new router...
2)Make sure the ethernet cable from your PC is securely...
3)Click Retry to try installing your router again."
I tried all several times and still I end up on that screen message.
View 5 Replies
View Related
Sep 5, 2011
I'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies
View Related
Oct 4, 2012
I previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
Â
How can I reset the static DNS ip address back to 0.0.0.0 ?
View 4 Replies
View Related
Feb 28, 2013
I am trying to connect to a new VPN using my E2500 router. As soon as I connect, the connection breaks.
View 1 Replies
View Related
Sep 3, 2012
i buy a new e2500 from staples. but when i try to register the product. it shows me  "Serial Number you entered is invalid.".  i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies
View Related
Dec 18, 2012
I want to add my E2500 as a second wireless router to cover my entire house.I have a Motorola Surfboard SBG6580 cable modem (Time-Warner) at one end of the house.I added via powerline Ethernet connection a new E2500 wireless router at the other end of the house.The E2500 set-up with all defaults and has the same SSID and Password as the Surfboard cable modem.It seems to work OK, but I wonder about network confusion/interference.Do I have to configure the E2500 in some manner to allow seamless roaming of my wireless devices (iPad, Cell Phones, Netbook)?I had an RE1000 with just the Surfboard, but it did not quite do the trick, and does not like both routers connected at either end.
View 9 Replies
View Related
Nov 23, 2011
How To Reset E2500 Router
View 1 Replies
View Related
Jan 23, 2012
I am trying to setup a WAP with my linksys 2500. I am currently using a Gateway connected to my DSL and am looking to set up the access point through the E2500.
View 1 Replies
View Related
Nov 18, 2011
So, i have a e2500 router and find that every so often, I have to unplug it and reset it because I am losing my internet connection.Â
View 7 Replies
View Related
Dec 22, 2012
How to set router to use as Slind Box Pro?
View 3 Replies
View Related
Jan 4, 2012
I currently have my E2500 connected via wired LAN (not WAN) port on another router. The E2500 has an LAN IP of 10.0.0.2 and the router has 10.0.0.1 and a dhcp range outside of these. DHCP is disabled on the E2500. I can use my E2500 as a wired access point with no difficulty I plug something in and it calls the router and gets an address, but I can not get DHCP through the wireless of the E2500.
View 2 Replies
View Related
Aug 7, 2011
I have Time Warner as my internet company. I recently purchased a new Linksys Router Mode E2500 because I have been having issues with my old router. My internet was disconnecting sporadically. After connecting the new router, a started getting the same issue. I replaced my internet cable modem to a Cisco 2100 modem (provided by Time Warner). I noticed that the issue keeps happening sporadically which makes me believe it is my Linksys router. Every time a new wireless connection is connected, my modem circuit dies. This happens sporadically.
View 4 Replies
View Related
