I get about only 500 KB/s for accessing files (as a network drive), regardless of the size of the file (even full 4GB iso)If I watch a video via media server however I get around 3MB/s.My firmware is currently on 1.00 and I am not upgrading due to the notorious media server problem.
View 5 Replies
E4200 2.4 channel extremely slow.
View 7 Replies View RelatedAll I want is functional Wi-Fi in my house like the rest of the world. Unfortunately, I cannot have that for whatever reason.
Now that I said that, Let's me get down to explaining my issue. I orginally owned a Linksys WRT350n. This router worked fine for years, untill one day I decided to do a speed test on my new Motrola Atrix. My Wired computer gets ~22000kbps down and 4000kbps up... My wireless speedtest on my Atrix yielded 2000kbps down and 4000kbps up. I assumed it was the phone, so i went and tried every other wireless device in my house. Everyone of them got the same result.. 2000kbps down.. 4000kbps up.
At this point I went into my router settings and tried every available channel, all of them yielded the same result of 2000kbps down and 4000kbps up.. At this point, I assumed it was the router. Ive had it for a few years and figured it was just reaching EOL. I rushed to my nearest bestbuy to pick up a brand new Linksys E4200. I brought it home, hooked it up and was eager to test my new wireless speeds. Unfortunately the same results of 2000kbps down and 4000kbps up was the yield. Once again, I've tried every possible channel with no change to my speeds. At this point I called up Linksys/Cisco support.. They were POSITIVE it was a hardware issue and had me exchange the router, even though I informed them i had the same issue with my older router of a different model. I went along with it anyway, and exchanged my router. Same issue. I called Cisco/Linksys back up and informed them, and basically they told me "they'd make a note of the issue and call me back at a later date."
I downloaded a WiFi Analyzer on my cell phone. Theres only two other dectable networks in my area, and they are low low low signal. So, I don't believe it's heavy saturation. The router is in the same room as 3 of the wireless devices that get 2000kbps down/4000kbps up. So it's not range either.
i have a newly formatted (i.e. empty) 2TB WD my book elite which when i connect it to my computers usb port, can transfer a 6gb video file at over 100MB/s according to the win 7 detail box. However, when i connect it to the usb port on the back of the e4200 and try to transfer the same file, it only goes at 8MB/s max ... it appears to be going at usb 1 speed. i've got the latest firmware on both the e4200 and the my book 1111 and everything seems to be working fine for both, except this transfer rate when connected to the e4200.granted, cisco doesn't specifically list this drive as being tested, but the router does recognize it and shows it as usb 2.0, but yet the transfer speed is just too slow.8MB/s is just not workable...i could just connect the drive directly to the computer and share it that way, but connecting it to the e4200 was one of the reasons i bought the e4200.
View 8 Replies View Relatedi just replaced my malfunctioning E4200 with the new EA6500 and the speeds are almost like dail-up. I haven't changed ANYTHING in regards to the setup, so I don't see what I could possibly be doing wrong. I even went as far as hooking up the old E4200 to my laptop while having the EA6500 hooked up to my desktop so that I could cross-reference the router settings. They were exactly the same.
View 9 Replies View RelatedFor the last 4 years I’ve been using the Linksys Router, model WRT150N V. 1.1 and never had any problems—until now.Yesterday I noticed that my wireless devices (i.e., two computers, tablet and Internet radio) either don’t work at all (the Internet radio) or the pages load extremely slowly—for example, the tablet has become, for all intents and purposes, unusable. Since my ‘main’ computer is connected directly to my cable internet, I know that there is nothing wrong with the Internet connection itself, only with wireless connection.I disconnected the Linksys Router for 2 minutes and reconnected it, but to no avail. I know that I have not made any changes to any software/hardware that might affect the speed.Since I also happen to have access to another wireless Internet connection (a different provider), I connected to that network and all my wireless devices were working perfectly. Therefore, I think the problem must be with the router. I am using Windows XP (on the main computer, where the router and Internet cable are attached).
View 5 Replies View RelatedI currently have a Linksys E1200 router and I am getting anywhere from .3-.5 of a megabit per second download speed while upload speed ranges from 2-5 Mbps. This is very strange to me as I have never seen a connection this slow or one that had a higher upload speed than download speed.
View 7 Replies View RelatedI just purchased an E-3000 and when I log into the user interface it seems changing pages and saving settings takes forever. I click on a section in the router menu and it takes what seems like 30 seconds for the page to change or accept the new settings. It's not my browser it's definitely a Linksys Router issue. I updated to the latest firmware and latest Cisco Connect software as well. Is this slow user interface a normal thing with these routers?
View 1 Replies View RelatedNow that the firmware update allows us to plug a printer into the E4200, is there anyway to simultaneously enjoy network storage AND a USB printer?
View 1 Replies View RelatedWhen I connect my WD My Book Essential 3TB (which is listed as officially compatible with the E4200), I get the following screen:
The E4200 does not detect my hard drive, nor is there a bar saying "detecting".
My problem started when I could not create any new folders through finder. I had to store new files in the root folder. Every time I entered the admin password, I got a message saying I did not have sufficient permission to perform such a task. I then went on to create a new user within the admin group and continued getting the same message. Finally, I formatted the drive directly through my computer and reconnected. And now my HDD is not detected at all.
I have an iMac running OS X Lion. The HDD is question has been formatted to Mac OS extended (journaled).
I've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.
My router usb storege was working fine with my old videos and streaming fine too but now im putting some new videos on the usb storage my router its not showing the new videos on the usb storage.
View 2 Replies View RelatedI got E4200 with latest firmware (updated two days ago) and WD Studion with 2 Tb drive (it is HFS+ file system)Once I connect this drive to router I am not longer available to access 192.168.1.1.
View 5 Replies View Relateddoes e4200 have cifs support. I ask because I have a hard drive connected thru the usb and trying to setup nas storage. But for the hp touchpad to mount it it needs cifs I guess.
View 1 Replies View Relatedif Linksys will be increasing the size limitation of the E4200 USB storage devices? Will the next firmware allow larger drive sizes? I only bought the thing to share via the router my digital content that is stored on an 8TB external device. What is the perpose to the limit in the first place? Is this a hardware or software limitation of the device?
View 2 Replies View RelatedI have been having issues with my home network since upgrading my router from a WRT54GS to an E4200. Prior to this I had no difficulty in accessing my home group or my home network. I have 2 laptops, both are running Windows 7 Ultimate, one is x64 and one is x32.
Laptop 1 (x-64) can access my home network in all its glory ONLY wirelessly...plug in the Ethernet cable and I can't access laptop 2 or my network storage...Laptop 1 is also unable to join my homegroup even after deleting the old one and creating a new one.
Laptop 2 (x-32) can access my home network in most of its glory ONLY wired...unplug the Ethernet cable and I can't access my network storage and it becomes unavailable to Laptop 1 over the network. Laptop 2 is also not able to connect to Laptop 1 even though Laptop 1 can (sometimes) access files from Laptop 2's shared folders.
Also Laptop 2 cannot see a home group created by Laptop 1, but can create a homegroup that Laptop 1 can see but CAN'T join.I have run all the trouble shooters that the system throws at me to no avail, they all say that I have an unknown network error that it can't fix.I do have internet access on both laptops regardless of wired or wireless, and I spent over 2 hours with Cisco "senior" tech support only to be disconnected and realize that they had no clue about this new router..
This firmware bad, because my sync program, can't set create date of files on external usb storage connected to router, on 1.0.04 - all good.
View 5 Replies View RelatedI just bought an e4200 with firmware version 2.0.36 from Costco.I have set it up manually and have access to the internet for all of my wired and wireless devices.Unfortunately, I cannot access the USB storage via mounting a share, the media server or the FTP server. I have plugged in a USB storage device that is formatted with FAT32. The router detects it and allows me to create new shares in the Storage->Disk menu and Storage->Media Server menu - so I know it can read the device and see the folders. Strangely if I click "Scan All" in the Media Server, it finishes very quickly and never updates the "Last scanning time" field.There was a brief moment when the router showed up in the Network->Computer section of File Explorer, but I can't get it to show here again.
View 8 Replies View RelatedMy E4200 storage config (portions of it) does not persist through reboot cycles. We often have to reboot the router because we lose wireless conectivity, and each time we reboot, we lose our mapped drives because the router is no longer sharing the folders and permissions I set up. And in the storage settings, my shared folder setup looks like factory default (sharing only root /) after each reboot. Those settings do not persist. I have to restore my router config from a backup after each reboot, which is a real pain. Especially when the kids reboot the router to get their wireless back, but restore is just too complicated for them, and so they call me when they then can not access their network share folders with homework on them.
View 9 Replies View RelatedI am having a problem with my newly purchased Linksys E1000 router, I am having terribly slow network speeds while on that network.
Here are my network speeds with The e1000: (wireless) And here are the speeds with my old wrt54g: (Wireless) Here are the results directly hooked up to the modem: (wired)
I've tried setting the MTU to 1500, did a RMA with Linksys to see if it was a hardware problem, did a firmware update to the e1000, disabled DHCP and SPI, reseted my router and my modem....none of those things have worked
My ISP is comcast and I have a Arris TM502G modem
If I were to take a e4200v2 and use it as an access point (disable DHCP), would the USB port connected to a Hard Drive still function as network storage?
View 5 Replies View RelatedI have a problem with new E4200 WAN speed. I have 1Gb connection from my ISP, and my old Netgear router gives me about 350 Mbps WAN speed, but with new E4200 I only got 110 Mbps max download speed.Cisco live support tried suggested to change MTU from Auto to 1400 (and try different wlan channels, even that I don't use wlan). This MTU size change makes no difference with WAN speed. I have latest firmaware installed, router reseted several times, tried different cables etc. Also with same cable sets my old Netgear still gives about 3 times better WAN speed.WAN port (and all LAN ports) seems to negotiated at 1000 Mbps at both ONT (optical network terminal) and Linksys settings page, but unfortanately there is no way to change the setting from auto to manual at E4200 settings (and it is not possible to change any settings of ONT by user). I was thinking that if somehow it won't auto negotiate properly (even if the setting page says its ok) but maybe it actually negotiated 100 Mbps port to WAN.
View 9 Replies View RelatedMy transfer speed from HDD which connected to linksys e4200 reach max 2,3MB/s how it is possible to watch fullHD movie if its required minimum 5MB/s? Maybe I should make some adjustments? HDD-WD My Passport 750Gb Also connection speed max reach 144mb/s?? how to make 300mb/s ? wifi adapter is Intel advanced N + WiMax 6250 AGN last driver installed, also E4200 last firmware installed 1.0.0.2 all settings by default Max download speed 75Mb/s by utorrent but provider gives 100Mb/s By cable its ok, max speed 100Mb/s as giving provider
View 9 Replies View RelatedI have brand new Cisco E4200 and WD Passport 500Gb.When it connected to router wireless (802.11n 300Mbit/sec) file transfer speed is around terrible 3 MB/sec. Same hard drive directly connected to my Mac Book Pro Unibody produce 30MB/sec. However my internet connection thru the router fairly shows 12MB/sec.It sounds funny, but for me is 4 times faster to download file from the Web rather the from hard dive that I'm holding in my hand.
View 5 Replies View RelatedI installed the E4200. Internet works fine, and the internet connection is maximum performance. But if I copy a file between laptops, or to my mediaplayer (AC Ryan HD2), the connection is 3MB/s tops. I changed to the 5gHz and N settings, still no change.
View 6 Replies View RelatedI recently bought the E4200 thinking it would be the latest and greatest, and I wouldnt' have to worry, but after just a simple test of transferring files between my Home Server, and my PC (Both connected over Gigabit ethernet using CAT6 cables, with only the E4200 inbetween).I use to get anywhere from 40 MegaBytes/second to 50MegaBytes/second on my D-Link 655.But now I am lucky to barely get 20 MegaBytes/second. Is there an issue with this router? or am I expecting too much from Linksys?
View 6 Replies View RelatedE4200 with an external hard drive WD My Book (1TB) connected to the router via USB.Desktop PC (Windows 7) connected to router via Ethernet cable.Laptop PC (Windows 7) connected to router via wireless connection.I wanted to create a central media (videos/pictures) file on the external hard drive connected to the router. However, the transfer rate is terribly slow. Interestingly, it is 50KB/second when copying from the Desktop (via Ethernet) and 1.6Mbps when copying from the Laptop via wireless.
View 9 Replies View RelatedI usually download and update on my Nas in my house. I conneting my nas to the e4200. My laptop get full wifi from my router, but the speed up and down is very slow. I setup the wireless everything is auto.
View 1 Replies View RelatedUsing 1.0.03.
I am seeing something pretty bizarre: when trying to copy files between two computers (both Windows 7 SP1 64bit), both physically plugged into the back of the E4200, I see extremely slow transfer speeds: 1.0-1.1 MB/sec. Both computers are fast (i7-2600K, both using SSDs) and both have gigabit ports (and the 4200's web UI shows both ports in question as operating in gigabit mode).
This is so slow as to be sort of funny. Each of these computers see speeds well in excess of that when transferring between the computer and outside internet sites...so it's kind of funny that two computers plugged into the same switch in the back of the 4200 see 1 MB/second.
Recently purchased a Linksys E4200.Computers on network:Two hard-wired gigabit desktops: one Windows XP, one Windows 7One hard-wired 100mbps desktop running Windows 7One laptop with an Intel 4965AGN running Windows 7.File transfer rates between any of the desktops and the laptop is very slow: ~2 megabytes/s
File transfer rates between the gigabit desktops is good (~50 megabytes/s, hdd bottleneck), transfers between the 100mbps desktop and one of the gigabit machines gives ~10 megabytes/s.Currently running on the 5Ghz band, connected with N at 300 megabits, good signal strength. Disabled mixed mode on this band, enabled N-only.Use a scanner tool, I can tell that there are no other networks on 5Ghz band.Also, tried 2.4 Ghz band and got similiar low speeds.These transfer rates are much below what other people report for real-world throughput. Any ideas? I know there is an Advanced Wireless config page, is there a setting there that might work if adjusted?
I have cable @ 15Mbps down, 2Mbps up. The cable line comes into the crawl space in my daylight basement. I have 3 Cat-5 cables running through the house. 1 to the TV downstairs, and then 1 each to 2 bedrooms on the second floor (one of which is my home office). In the home office, this Cat-5 is connected to a 24-port switch. I plug my printer, NAS, computers, etc into this switch.I have a WRT54G2 v1 that I was using as my Router/AP.I have a 1st & 3rd generation iPad. The iPad 3 plays YouTube videos in HD. About 6 weeks ago I started to get slow YouTube video playback on my iPad's. They would play a few seconds, then pause to buffer, etc. It used to be that videos started playing almost immediately and would never buffer.
Using Wifi Analyzer for Android, I noticed my neighborhood is saturated with 2.4Ghz wifi. So, I figured it must be that the 2.4Ghz band is saturdated and if I moved to a 5Ghz band, the YouTube buffering would be fixed.So, I purchased an E4200 (v1 I think) from Amazon. I bought this Router/AP because it supported the 5Ghz band. It also I connected it to my cable modem and setup everything. Still slow YouTube, and now YouTube videos are slow on my laptop (connected via ethernet). I still get ~15Mbps over ethernet or wifi using the speed test page provided by my ISP, but YouTube videos are VERY slow.
Just upgraded my E4200 to firmware 1.0.03 (from 1.0.01). I have some new issues, questions, and some outstanding issues.
1) Web interface over https is now painfully slow.
2) Does DDNS work in bridge mode? DynDNS allows the sending of an update without an IP address, so it should be able to work.
3) Does accessing the management interface in bridge mode count as local or remote?
4) I'd really like to be able to get WOL working through the router. I managed to create a static DHCP reservation for 192.168.1.254 to ff:ff:ff:ff:ff:ff, but I don't think the router added that entry to the ARP table, is there any way to do this.
(I think have WOL forwarded to 192.168.1.254). 5) Should the router be providing some local dns hostnames? For example I have the device name set up in the local network setup, but it won't resolve. Similar for connected devices, especially those with with a DHCP reservation. 6) In bridge mode, does it matter which port is used to connect to the other network device? Does it have to be the WAN port?
Im trying to optimize my E4200 settings and Ive noted that ping and download speeds are extremely slow for the internet service I signed up for. Ping speeds are consistently more than 1000ms and dowload speeds typically are less than 3Mbps. These are for both wireless and wired connections to the E4200 router.
When I disconnect the router and hardwire my laptop directly to the the modem, ping speeds are less than 100ms and download speeds are 20Mbps.
Simply put, webpage loading is at a snails pace with wireless and wired connection the router, but blazing fast when hardwired directly to the modem.
On a seperate issue, the iMac I have is also **bleep** slow even when hardwired directly to the modem. Is there an obvious router setting Im screwing up? Router is updated with the latest software.
