i just replaced my malfunctioning E4200 with the new EA6500 and the speeds are almost like dail-up. I haven't changed ANYTHING in regards to the setup, so I don't see what I could possibly be doing wrong. I even went as far as hooking up the old E4200 to my laptop while having the EA6500 hooked up to my desktop so that I could cross-reference the router settings. They were exactly the same.
View 9 RepliesAll I want is functional Wi-Fi in my house like the rest of the world. Unfortunately, I cannot have that for whatever reason.
Now that I said that, Let's me get down to explaining my issue. I orginally owned a Linksys WRT350n. This router worked fine for years, untill one day I decided to do a speed test on my new Motrola Atrix. My Wired computer gets ~22000kbps down and 4000kbps up... My wireless speedtest on my Atrix yielded 2000kbps down and 4000kbps up. I assumed it was the phone, so i went and tried every other wireless device in my house. Everyone of them got the same result.. 2000kbps down.. 4000kbps up.
At this point I went into my router settings and tried every available channel, all of them yielded the same result of 2000kbps down and 4000kbps up.. At this point, I assumed it was the router. Ive had it for a few years and figured it was just reaching EOL. I rushed to my nearest bestbuy to pick up a brand new Linksys E4200. I brought it home, hooked it up and was eager to test my new wireless speeds. Unfortunately the same results of 2000kbps down and 4000kbps up was the yield. Once again, I've tried every possible channel with no change to my speeds. At this point I called up Linksys/Cisco support.. They were POSITIVE it was a hardware issue and had me exchange the router, even though I informed them i had the same issue with my older router of a different model. I went along with it anyway, and exchanged my router. Same issue. I called Cisco/Linksys back up and informed them, and basically they told me "they'd make a note of the issue and call me back at a later date."
I downloaded a WiFi Analyzer on my cell phone. Theres only two other dectable networks in my area, and they are low low low signal. So, I don't believe it's heavy saturation. The router is in the same room as 3 of the wireless devices that get 2000kbps down/4000kbps up. So it's not range either.
Unlike other people, I haven't (yet) experienced any flapping of the wireless connection: it's stable but slow.
My problem is that Samba share speed are 50MB/s without using the WUMC710 (connected directly to the router) and about 10 MB/s with connection to the WUMC710. Computers have gigabit NICs and proper cables.
The WUMC710 is about 5 metres from EA6500 and there are no obstacles. The WUMC710 says that signal is 100%.
On the EA6500 the 5GHz band is on and I have tried almost every possible compination with the settings: all the way from Mixed and full automated to Only AC and 80MHz. I also tried resetting both devices.
Download speeds, per speedtest.net and speakeasy, are about 20mbps.When the speed test gets to the upload part, it usually hangs or takes a long time before giving me a result of about 0.04mbps. Basically, it's so slow, it sometimes just gives up and times out.This translates into a real shoddy internet experience because something as simple as choosing airline tickets requires your computer to "upload" your choices. And of course, if that doesn't happen within a certain amount of time... Timeout! I have tested the connection without my Netgear FVS336G Dual WAN router in the way and it is much better so I'm certain it's the router.When I tell the router to use WAN 2, which is where my AT&T DSL connection is on, the upload works just fine (about .4 mbps - I'm provisioned at 512kbps so it's fine).Also, this is the case on ALL computers on the network - wired, wireless, PC, Mac, iPhone, iPad, you name it. So, it's definitely not device specific.
View 1 Replies View RelatedWe have an ASA 5510 and are experiencing unbelievably slow speeds. I noticed a problem last Thursday with users complaining of slow speeds and realized our interface had a ton of errors and was running at half duplex. I contacted the ISP (we are connected to their 3750) and they swore up and down they were set to full. So they had me switch to full and the interface shut down. I asked them to switch to auto and the interface came back up and we went to full, and of course the errors and colisions stopped. However the errors and packet drops have not stopped. The ISP sent out a technician and they determined it wasn't a problem on their end by plugging in a laptop and testing the speed--that worked fine. Eventually I plugged in a Sonicwall and bypassed the ASA completely and that worked fine. We plugged the ASA back in and we we went back to dropping packets. I put an old config on the ASA and oddly enough it seemed to have fixed the problem but we were still dropping packets. So I put the most recent config back on and that worked fine up until today. We're back in the some boat we were last week. So my first question is when I do a show int and see packets dropped - is that normal because of ACLs etc, or would that be show in another place? Here's an output of show int and show asp drop:
HQ-ASA# show asp drop
Frame drop: Flow is denied by configured rule (acl-drop) 3366 NAT-T keepalive message (natt-keepalive) 423 First TCP packet not SYN (tcp-not-syn) 406 TCP failed 3 way handshake (tcp-3whs-failed) 135 TCP RST/FIN out of order (tcp-rstfin-ooo) 462 TCP SYNACK on established conn (tcp-synack-ooo) 46 TCP packet SEQ past window (tcp-seq-past-win) 50 TCP invalid ACK (tcp-invalid-ack) 9 TCP Out-of-Order packet buffer full (tcp-buffer-full) 29 TCP Out-of-Order packet buffer timeout (tcp-buffer-
[code]....
I have not made any configuration changes to the ASA ina couple of months. The interface counters were cleared about 45 minutes ago if that's how quickly the errors/packet drops are adding up.
I've recently upgraded the configuration on one of our 1130 series standalone access points. I've implemented RADIUS authentication, WPA2 encryption etc. in an effort to make our network more secure. While this part seems to be working as planned, our data transfer speeds have taken a major hit. On our test AP, with only one laptop connected, the laptop will report a connection at 54 Mbits. When using any speed test service the speed reported is approximately 15 Mbits. We have 100 Mbit internet, and desktops connected to ethernet show much higher speeds. When transferring files via our own LAN, data transfer rates average approximately 2 Mbytes/second. I've tested this on 3 separate laptops, some relatively new, and it seems they all get the same speeds.
Long story short, our wireless seems to be operating under a third of its reported speed.
E4200 2.4 channel extremely slow.
View 7 Replies View RelatedI just purchased an E-3000 and when I log into the user interface it seems changing pages and saving settings takes forever. I click on a section in the router menu and it takes what seems like 30 seconds for the page to change or accept the new settings. It's not my browser it's definitely a Linksys Router issue. I updated to the latest firmware and latest Cisco Connect software as well. Is this slow user interface a normal thing with these routers?
View 1 Replies View RelatedI've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.
I just got my EA6500 router before the holidays and set it up before going on vacation so I can't be sure that wireless was ever working at full speed, due to lack of testing. As it stands now my desktop (hardwired into the router) gets d/u speeds of around 16 to 20 Mbps down and 1 to 2 Mbps up, this is pretty standard from my old router and in the range for what I pay RCN in Massachusetts for. When I connect my wife's Mac and my Laptop to the wireless I get in the range of 1 to 2 Mbps down and 1 to 2 Mbps up
View 9 Replies View RelatedI am having a problem with my newly purchased Linksys E1000 router, I am having terribly slow network speeds while on that network.
Here are my network speeds with The e1000: (wireless) And here are the speeds with my old wrt54g: (Wireless) Here are the results directly hooked up to the modem: (wired)
I've tried setting the MTU to 1500, did a RMA with Linksys to see if it was a hardware problem, did a firmware update to the e1000, disabled DHCP and SPI, reseted my router and my modem....none of those things have worked
My ISP is comcast and I have a Arris TM502G modem
My Belkin F7D4301 Router has the fastest wireless speed of maybe 2MBps but wired with a cat5e cable to my asus laptop of almost 7MBps. I have a one smart TV, one blue ray, one roku, and a nexus 7 using the 2.4 channel.
My Wireless 2.4 settings are channel 11, Extension channel 7, Wireless mode N (have tried with just g and b, g, and n modes), Bandwidth 20/40, Protected mode on, QOS off.
I've talked to Belkin tech support, they are the ones who had me set up my 2.4 channel this way but my wireless speeds stay just under 2MBps, they just want to keep sending me the same model Router because they think each of the new ones they send me is defective.
Am I doing something wrong or is 2MBps the best wireless speed I'm going to get?
For the last 4 years I’ve been using the Linksys Router, model WRT150N V. 1.1 and never had any problems—until now.Yesterday I noticed that my wireless devices (i.e., two computers, tablet and Internet radio) either don’t work at all (the Internet radio) or the pages load extremely slowly—for example, the tablet has become, for all intents and purposes, unusable. Since my ‘main’ computer is connected directly to my cable internet, I know that there is nothing wrong with the Internet connection itself, only with wireless connection.I disconnected the Linksys Router for 2 minutes and reconnected it, but to no avail. I know that I have not made any changes to any software/hardware that might affect the speed.Since I also happen to have access to another wireless Internet connection (a different provider), I connected to that network and all my wireless devices were working perfectly. Therefore, I think the problem must be with the router. I am using Windows XP (on the main computer, where the router and Internet cable are attached).
View 5 Replies View RelatedI currently have a Linksys E1200 router and I am getting anywhere from .3-.5 of a megabit per second download speed while upload speed ranges from 2-5 Mbps. This is very strange to me as I have never seen a connection this slow or one that had a higher upload speed than download speed.
View 7 Replies View RelatedI get about only 500 KB/s for accessing files (as a network drive), regardless of the size of the file (even full 4GB iso)If I watch a video via media server however I get around 3MB/s.My firmware is currently on 1.00 and I am not upgrading due to the notorious media server problem.
View 5 Replies View RelatedI purchased an EA6500 router on March 1 2013 – since then my wireless network has became very unreliable. The network runs fine for a short period of time then it gets extremely slow. I constantly have to reboot the router to see better performance. When I run the built-in router speed check, it shows that I am getting 20 Mbps for downloads which is what I expected to see and then as time goes on, the speed goes as slow as 1 Mbps for downloads. I finally had to go back to my very old Linksys WRT54GS router to have a stable network again. I called Linksys customer support and they want to charge me a fee to diagnose the router that will only be refundable if they find any issues. I find it completely unacceptable to have to spend more money for an item that is only a month old that will probably show no issues when they run their diagnoses since they had me reboot the router while I was on the phone with them. I want to warn others not buy this router especially when the company cannot stand behind their product that is only 34 days old!
View 2 Replies View RelatedI bought WRT160Nv3 3 months ago . The computer is wired to the router . So I noticed 5 says ago that my download speed is slower – from 70mbps to20-30mbps . I have called the cable company and their tech support reports a good signal to the house. My firmware is up to date . I tried hard resetting the router-nothing.Plug,unplug still nothing.
View 9 Replies View RelatedI have a WRT600N router. I have one PC that is connected to the router via a wired connection. I also have an iPad (3rd generation) that is connected to the router via a wireless connection. On my PC, I went to speedtest.net and determined that I am receiving like 20MB downloads via the wired connection. However, my iPad only gets approximately less than 2 MB download speeds. I have tried reseting the router and I do have what I believe to be the latest firmware update (Firmware Version: 1.01.36 build 4). I also receive the slow download speeds when I try connecting the other wireless devices. I assume my problem has to do with some sort of configuration setting found in the router configuration page (http://192.168.1.1/). The router is only a few feet away from my iPad so the signal strength is strong. I just don't understand why I'm receiving such slow wireless download speeds.
View 9 Replies View RelatedI have an E1200 that will work fine for a while, then suddenly the download speed for all wireless devices will drop to between 20-30 KB/sec. It happened last night when we were watching videos on Hulu. We were blazing along fine, when all of a sudden the connection was horrible enough that we had to stop watching. We have no idea what changed - there are only two of us in the house and we were both passively watching Hulu.
This has happened before, and usually changing something like the wireless channel has fixed it, but not this time. The PCs we have that are connected to the router via Ethernet get between 1-3 MB/sec, so I know it's not the modem or the ISP.The signal strength is good (4-5 bars). I have tried repositioning the router and the wireless reciever but that hasn't worked.I have the latest firmware for the router as far as I know (v2.0.02).
I have tried every channel available (including "Auto"). I have tried switching the Channel Width between Auto and 40 MHz. I have tried resetting the router to factory settings and re-uploading my configuraiton. I have tried setting QoS.
Set up my new E4200V2 last night, everything appeared to be working but while streaming videos over wired LAN I get short hiccups over wired. While streaming videos, a few second long pause is really, distracting, this is a deal breaker and my previous router (DIR-655) had no issue streaming any videos. The wiring has not changed, only the router.I set up a ping between two wired linux boxes, and get: [code]
Whoa, 10 ms over gigabit LAN. This is crazy, but doesn't tell us much. The 10 ms was one out of hundreds of pings, so its only intermittent. This might explain the hiccups, but this router doesn't appear to log anything, so its hard to say.Next was scp transfers, which never exceed 15MB/s, in either direction. For gigabit, wired LAN this is awful, with my previous DIR-655 I would get at the very least 40 MB/s, in all situations.Next up, iperf. I set up iperf on the two hosts, and iperf reports reasonable gigabit speeds. [code] Tonight I am thinking of reverting to an old firmware, doing a hard reset and seeing if it persists, and if no ideas come up in this forum, it is getting returned, 15MB/s over gigabit lan is terribly broken.
I upgraded my old router to a Linksys E1200 about 2 months ago. Like others with Comcast, I now have a lot slower internet speeds. I've updated everything, disabled WMM. I'm still getting slow speeds. My download speed is 3.12, which is not that bad for me. However, my upload is just below 1.
View 7 Replies View RelatedI have been experiencing intermittent issues with download speeds of 1-3 MB and ironically upload speeds of almost 10MB. When everything is working fine I get download speeds of about 35MB and upload speeds of 5MB which is normal. This issue comes and goes. I had Comcast come out several times and we finally pinpointed it back to the WRT400N router. The Comcast modem is a Cisco DPC3008 model. I know there are known issues with the Cisco WRT400N but have had a hard time finding the information. Any known issues for this model and if so what are the fixes. BTW, the firmware is up to date.
View 2 Replies View RelatedThe new firmware is killing the video streaming performance I have to revert to the old firmware Ver.1.1.28.146072 to be able to stream videos from the media server. I have been waiting a long time for a decent Firmware that will fix the multiple issues with this router but this is ridiculous every new firmware update brings more issues to the table I am feed up with the Cisco developers I have a WRT610N router that is performing better than this lemon router that Cisco just introduced in 2012.
View 2 Replies View RelatedI have been having a problem with my router for the past two weeks and my ISP (RCN) has done nothing to fix it so maybe with our nerd power combined we can find a solution!My router runs fine about 60% of the time, I get 20-24Mbps down and 2Mbps up connect wirelessly. the other 40% of the time the download speed suddenly drops to 1.5-2Mbps down and 1Mbps up. There is nothing in particular that I will be doing at the moment it just suddenly dies.Things I have done that have not worked.I have changed my channel to 1,6,and 11.Updated firmware.Factory Reset (New broadcast name/password).Set up static IPs.I have tried disabling WMM Support and this just kills any connection wirelessly to the router.Is there anything else you can think of to fix the issue, or should I just be demanding a new router the next time they come
View 1 Replies View RelatedUsing 1.0.03.
I am seeing something pretty bizarre: when trying to copy files between two computers (both Windows 7 SP1 64bit), both physically plugged into the back of the E4200, I see extremely slow transfer speeds: 1.0-1.1 MB/sec. Both computers are fast (i7-2600K, both using SSDs) and both have gigabit ports (and the 4200's web UI shows both ports in question as operating in gigabit mode).
This is so slow as to be sort of funny. Each of these computers see speeds well in excess of that when transferring between the computer and outside internet sites...so it's kind of funny that two computers plugged into the same switch in the back of the 4200 see 1 MB/second.
I am only getting 10-14 mbps when I should be getting 30-35 (using the gigabit ports). I thought it might be my provider but today I connected my old netgear router and the speed was 32-34 mbps. Is there some setting that I should be looking at?
View 5 Replies View RelatedI'm having very slow file transfer speeds between the 2 computers on my network. One is a gigabit pc wired (cat6) to the e3000. The other is a wireless N laptop. Both computers running Win7. Speeds are like 1.5 - 2 MB/s. when I connect the laptop to the router with a cable (cat6) I get proper high speed. Trying to figure out if it's a problem with the router or windows or what. Speedtest.net says I'm getting 16 MB/s DL wirelessly to my laptop. Shouldn't wireless N be capable of higher speeds than 1.5 MB/s?? Tests are done approx 10 feet from the router.
View 1 Replies View RelatedI recently set up a new E1200 router to replace my old one. We are having problems with very slow download speeds (often <0.10 Mbps) even while the upload speeds are OK (8-10 Mbps). Our previous download speed over wifi was 10-15 Mbps.When I first set it up, the download speed was very poor on the initial computer. After fooling around, it was fine. I don't know what I did that made it speed up. However, my wife's computer has had very poor download speeds. After rebooting my computer, the download speed has also dropped bak to <0.10. I was able to stream Hulu on my Wii just fine an hour ago.
View 1 Replies View Relatedi recently switched from a wrt54g to a Cisco e1200 and my average torrent download and upload speeds went to 1200/kbps 100/kbps to around 200/kbs 0-1/kbps i got the latest firmware tried different channels disabled the wmm I've also tried wireless n only and wireless g only. I have no way to test the wired speed. I have a n adapter.what do i do.
View 9 Replies View RelatedI'm having a problem where my connection speeds slow down on my iOS devices. I have a EA2700 router. I have PC hard wired into the router, which maintains steady speed test numbers when other devices slow down.i have another pc that connects wirelessly (2.4 only) that maintained speed white the other devices slowEd down. Both my iphone5 and new iPad would slow down. The quick fix wasto turn the wifi on the device off, then the speed would return when reconnected. Also clicking "renew lease" in the iPhone wireless settings seemed to correct the issue.I'm not sure if there is a setting on the iOS devices or the router I can change to stop this.
View 3 Replies View RelatedSince we purchased our router in February, we've had intermittent problems with speed, and now it seems to be permanent. If we connect directly to the Comcast modem, everything is fine. If we connect to the router, directly or wirelessly, speeds drop to <3.
View 9 Replies View RelatedI have a Linksys WRT160N V2 wireless router that I am using with my Comcast Internet service. When I connect to the router via cable, I get download speeds up to 52Mbs (per www.speedtest.net). When I test my wireless connection, I can only get download speeds up to 14.5 Mbs, even though the Windows “Wireless Network Connection” speed shows 54.0 Mbs. I also verified this with another laptop, and got the same results. I also checked upload speeds, both wired and wireless I get the same speed of 11 Mbs.
Is there some reason I can’t get faster download speeds with a wireless connection?
I Have BT Infinity and they are pushing 70mbps to my house ....i bought an EA6500 and i had real bad internet speed but amazing conection speed with my BT Home HUB3 ... 23Mbps with Cisco EA6500 and 68Mbps with my BT Home Hub3. I found out it was the Media Prioritization so just to be safe i reset my factory settings and made sure it was turned off. Just like magic i get the same now as the BT Home HUB3 .
View 1 Replies View Related