Linksys Wireless Router :: WRT160N Ping Response Time?
Aug 31, 2009
I have a brand-new WRT160N router (just installed FW v3.0.02) that I am using in mixed mode, 20MHz only, Channel 11, not filtering anonymous requests, beacon at 2306, RTS at 2307, fragmentation at 2346, MTU at 1400.
These settings bring the response from a simple ping command over the wireless network down to approximately 6ms on average, which is good. However, when I still noticed inconsistency with my internet response over wireless, I decided to do a test.
By simply running the "ping" command on 192.168.1.1 (the router address) over the wireless network repeatedly (approx 3 seconds between commands), I can see that approximately every 65 seconds or so, router response time increases to over 100ms for a few seconds, then decreases down to 6 ms or so for another 65-70 seconds. See the chart below. The interval looks pretty consistent to me, with the exception of one stretch where it goes for over two minutes without a spike. I see this pattern regardless of what else I'm doing over the network. I do not see this behavior running the same test when physically wired to the router (ping response time is a flat line at 0ms).
View 4 Replies
ADVERTISEMENT
Nov 9, 2012
Each time I'm rebooting my E3200 device my ping to my ISP is 20ms. Few hours later the ping goes up to 300-500ms.Than I reboot again and the ping is going down to 20ms again.
View 5 Replies
View Related
Mar 29, 2012
I've updated latest firmware & installed 5 pieces of WRT54GH at our building. Then I noticed each of them disappear from wireless connections list and IP scan list (no ping response). If they might not response to pings but they serve as switch without any problem, I mean there are no wired connection problems, they work as switch all the time. The problems are -again-
1-) Wireless lost and / or 2-) Ping response lost
Turning them off and on again will fix them. But I'm tired of bosses who complain about their faulty pc connectivity.
Don't they run 7/24? I tried to restart them on every 12 hours programmatically/remotely but it couldn't work.
View 1 Replies
View Related
Jul 13, 2008
I need to remotely monitor a WRT45G from a remote host on the Internet. As such, I want to allow ICMP ping replies on the public Internet interface. However, I have found no feature to allow me to do this. Similar Netgear devices do allow this feature. I suspect the answer is, "you can't do that".
View 2 Replies
View Related
Mar 20, 2013
I have the following LAN setup: I am trying to ping the Wireless Access point (10.60.1.1) from the Cisco Router (172.16.88.21) but I am not getting responces. I can however ping 10.60.1.1 from server (172.16.88.36). Tracert from the server shows that it is going through the Rotuer and Firewall.
View 8 Replies
View Related
Apr 22, 2011
I want to change ping latency because my application cannot run in 1ms or 35ms it will work on 600ms to 1500ms due to in VSAT minimum response time latency is 600ms to 1500ms.for i want to change in my 2003 server reponse letancy time.and we are use online accounting software and connecting through ftp server.kindly do the need full how to change response time frame in windows
View 2 Replies
View Related
Apr 17, 2013
Our company just recently bought a CISCO SA520W Security Appliance from a distributor here in the Philippines. Unfortunately, after a month of use, the LAN ports on the appliance started losing power. We reported this to the distributor and they sent a CISCO engineers to check on the unit. The engineers found the unit to be defective and need to be replaced.
Three weeks after the distributor pulled-out the unit, I have followed-up the status with them. They told me that they got no definite ETA from CISCO for the replacement unit. I followed-up with them again after a week. This time, they told me that the device is already in transit and it is coming from CISCO USA but they still don't have an expected time of arrival to give me.Does it really take more than a month for CISCO to replace a brand new defective unit? The serial number of our appliance is DNI1610G0G7.
View 1 Replies
View Related
Feb 9, 2012
Having issues with HTTPS sites being very slow after applying KB2585542? Once you remove this Microsoft patch everything returns to normal. It appears that the CSS does not handle the split-ssl requests properly. I have opened a TAC case but am not really getting anywhere as we seem to be the only company that is having this issue.
View 2 Replies
View Related
Oct 26, 2011
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies
View Related
Jan 27, 2011
I'm having trouble connecting using this new card i bought. i have installed the latest drivers and i can find networks and the signal strength is good too but when trying to connect after ive entered the passkey i get the message " no network found" or "did not receive response from router" or something along those lines. i can connect with my older card which is a wmp54g but that one shows less signal strength and my connection breaks from time to time (hence the upgrade to wmp600n) on a sidenote, my wmp600n card works perfectly fine under linux but i want it to run in windows (mainly for gaming) Im running windows vista 64 bit and the wmp600n has the latest drivers installed.
View 3 Replies
View Related
Mar 13, 2011
I am in the process of installing a 3750x (IOS 12.2 (53r) SE2 IP Base) Cisco Catalyst switch in a new network of just 2 PC's (2 hosts, OS windows7 64Bits). I have enabled SVI interfaces with the both hosts installed in 2 different network segments. We then start connectivity test. The response time for the PING command between both hosts remain below 1 millisecond, whereas the response time between the hosts and their correspondent SVI interface is variable, and at all time is higher than 1 millisecond, sometimes it reaches 17 milliseconds. (Note that the switch CPU usage is only 8% at the time of testing) We have performed this same connectivity test changing the 3750x switches and in two different locations obtaining the same results.
View 2 Replies
View Related
Dec 5, 2011
A network administrator wants to capture some network data. He opens Wireshark software, start capturing, and does the following:In PC-A, runs a command in command prompt. The network admin issues the command and sees there is ping response from the google.
View 3 Replies
View Related
Jan 28, 2013
I connects to the wireless box and has full signal but an exclamation mark is present.I have run some tests and the IPv4 and IPv6 say they have no internet access.I also run a full test and everything passed except the ping test which failed and it said: no response:default gateway response: dhcp server it suggested disabling security firewall but i'm not sure if that's the correct thing to do or even how to do that!
View 7 Replies
View Related
Jun 23, 2011
I replaced my old wireless router with a Cisco Linksys E4200, running firmware version 1.0.02 build 13 May 24, 2011. About once a minute the router sends an unsolicited DNS message to the IPV4 multicast address 01:00:5e:00:00:fb with a destination IP address of 224.0.0.251. The unsolicited message is a DNS response with source port 32784, transaction ID 0, flags 0x8400 (standard query response, no error), questions 0, answer RRs 2, authority RRs 0 and additional RRs 1. The two answers both relate to the router itself: one has Name Cisco18738.local, type A (host address), class 1 (IN), cache flush true, time to live 1 minute, data length 4, and the address of the router. The other is the reverse of the same address. The additional record is for Cisco18738.local, type NSEC, class IN, cache flush true, time to live 1 minute, data length 5, next domain name Cisco18738.local, RR type A (host address).
When my desktop computer receives these messages it logs an error, for example: "Jun 23 07:39:22 sauterws02 avahi-daemon[1067]: Received response from host 10.146.9.1 with invalid source port 32784 on interface 'eth0.0'" The 10.146.9.1 is the router's IP address. I also see these messages on the wireless link from my laptop.I suppose the E4200 is generating these DNS messages in a misguided attempt to make sure there is no old information about its name. Is there a way to turn them off? If not, is there a way to report this to Cisco as a bug?
View 9 Replies
View Related
Nov 9, 2011
I am trying to recover a WRT54GS v1 router from a bad flash. The power light is blinking and would not accept pings. Since I figured it was already hopeless, I attempted shorting pin 15 and 16 which cause it to start receiveing pings. My problem is it won't accept the tftp flash, I've tried both cmd prompt and auto upgrade utility. Upgrade utility says "Unable to get response from the server" however it is still accepting pings. Cmd prompt TFTP says it can't read from local file. I am using windows XP. Code...
View 3 Replies
View Related
Mar 20, 2012
I'm trying to configure an ASA firewall (FW2) for syslog and tacacs and am experiencing strange behavior. Both the syslog and ACS server are on the inside of another firewall (CoreFW). Whenever a log message is generated on FW2 the request is dropped by CoreFW and message '%ASA-4-313004: Denied ICMP type=0, from laddr FW2 on interface outside-b2b to syslog01: no matching session' is displayed. The same thing occurs for tacacs.
It appears that the syslog and ACS requests are generating ICMP echo replies, which the core firewall drops since no session exists on a lower security interface. I have access lists configured on CoreFW to allow the syslog and tacacs requests.
FW2 is running asa825-k8.bin, CoreFW is asa824-k8.bin
View 1 Replies
View Related
Apr 10, 2012
We have Four 2960S Switches in Stack. We have created Multiple VLANs. While Pinging from Member PC to Member VLAN IP on Switch, we are getting Higher TTL response & Some ping breaks for One Particular VLAN. While pinging from Member PC to Member PC, we are getting Normal Ping Response.
View 5 Replies
View Related
Apr 10, 2012
We got a switch issue here for 4507R-E with two sup6l-e supervisor running sso redudant. and we found that sometimes client can't ping through the local vlan ip add on the switch , can't logon the cli by telnet too. In the direct connected network device such as access switch and ASA , can't ping or telnet the 4507R too. when we made a forceswitch to sso standby supervisor from console , the problem solve and everything get fine . after that, we switch angin back to the origin supervisor , fine too.
before we made the supervisor forceswitch , we had check the system cpu usage is 15 - 20 % from console . also we had creat a new vlan 200, attach the notebook to 4507's vlan 200 port , the notebook can't ping or telnet the vlan 200 ip interface too.
View 1 Replies
View Related
Jul 29, 2011
I have a router WRT160N and I want to connect an AP using a wireless bridge to enhance my WIFI coverage.Which AP is recommended to use without cable together with the WRT160N?
View 7 Replies
View Related
Oct 15, 2012
confirm if the highest speed I can get over WiFi with WRT160N v3 is actually 270 Mbps (and not 300 Mbps as advertised), And there's one more thing - is it normal to have Signal: -51; Noise: -93, SNR: 43, Signal quality 53% if I am only 2 meters far from a router? TX power is set to 28.
View 3 Replies
View Related
May 1, 2010
I have a wrt160n v3. This is the 3rd one - both the first 2 were defective. I have spent approximately 8 hours troubleshooting the other 2 only to be told they're defective. So, I got a new one. Now, this one keeps cutting in and out. I want as my iPhone constantly switches from 3G to wifi on and over every minute. It really ticks me off! What can I do to fix this? This is a different issue than the original one (very slow) and 2nd (no signal). It's disappointing for a $90 router to do this. I also see the wireless icon on the router flash.
View 6 Replies
View Related
Jan 4, 2012
I have all the ports open necessary and i have upnp enabled. my modem is a webmaster DPC2100 series.
View 2 Replies
View Related
Jan 12, 2012
turning my wireless back on. Some how in attempting to create a shared file between my pc and my wife's Mac the wireless has been disabled. I have tried resetting the device several times following the instructions on line however I still can not get the wireless to re activate. I tried reverse directions from the posts on how to turn off the wireless but still no luck. I tried restoring the computer to a later date?
View 2 Replies
View Related
Dec 5, 2012
How will I reset WRT 160N?
View 1 Replies
View Related
Aug 3, 2012
I'm having an issue getting my tv to start connecting again to the wireless router.Have tried pin setup (timed out & didn't connect...attempted at least 10 times in this fashion)Have tried entering the password (router seems to refuse the connection to the tv)About a month ago, I was in the Network Magic Map & it looked like one of the laptops had been cloned, so I removed it from the network.
View 3 Replies
View Related
Sep 7, 2011
I have a WRT160N v3 Linksys Router and it keeps disconnecting and then reconnecting. It only disconnects wirelessly. LAN still works fine.I have tried a lot of different methods to solve this issue, but none seem to work.I am very dissappointed in the quality of the product. It has done this every since it was bought. I personally would have sent it in for repairs, but others in my household would not have agreed to that.
[code]...
View 1 Replies
View Related
Jul 15, 2011
Just tried to register my WRT160N V2 and when I tried firstly there is no option for the version 2 model and secondly it says my serial No is incorrect when I have tried it three times and have checked it thoroughly.
View 1 Replies
View Related
Aug 21, 2008
While using Skype I am experiencing poor sound quality, sometimes callers are unable to hear me at all and visa versa. There is a lot of cutting out. My internet connection is fine.
View 5 Replies
View Related
Oct 12, 2011
I have two PC's hardwired to this router that are working okay (although performance has been choppy lately). The past 4 days however, when I try to connect wirelessly I get connections that are repeatedly dropped. I am in the Settings section of my iPad 2 and it keeps rapidly switching between "connected" and "not connected". Firmware is up to date.
View 4 Replies
View Related
Aug 5, 2012
Desktop Xp 3 and connected printer, Comcast cable, WRT160N, wireless laptop w/ Xp 3. Printer is only parallel, and is connected to desktop. How to setup all and print wirelessly from laptop through WRT160N to printer on desktop?
View 2 Replies
View Related
Feb 23, 2012
How do I connect IPAD to Linksys router WRT160n?
View 2 Replies
View Related
Mar 22, 2013
I have a FIOS setup with their Router/modem providing DHCP and Wireless routing. The problem I have is that I have a mix of older equipment and newer equipment. The newer equipment is capable of supporting WPA2, the older is not. I would like the benefits of WPA2, but still would like to at times be able to use the older equipment.My solution was to use a WRT160N v2 router that I had as an access point and it also gives me switch capabilities for wired systems as the FIOS router in on a different floor than the Linksys router. Wired access works just fine and the wireless worked fine until just recently.Since both routers have the same default IP addresses I changed the Linksys to a different static IP and turned off DHCP. I left all of the other defaults the same. I set up the Linksys for WEP and created the key for security. Everything worked fine for the better part of a year, but recently I am having problems where some of the computers cannot find the network or find it then lose connection.
View 9 Replies
View Related
Jul 29, 2011
I am considering to purchase a Linksys Wireless router, but I just don't know which one to select.There are so many different types that seem to have very similar (if not equal) specs.If I just limit myself to the WRT120N, the WRT160N and the E1000, they all have 4 ethernet ports (10/100), and they all support 802.11 b/g/n for the wireless part.Obviously they all promise a blazing performance, and wireless coverage throughout the whole house, without (many) blind spots.But if their specs are the same, why are they different types?
View 2 Replies
View Related
