My storage link drive is accessible from my lan requireing a userid and password, but it can be accessed from outside my lan through ftp without userid and password. how do I change it so it requires a password from outside my lan when accessed as an ftp drive? I have the WRT350N
View 1 RepliesI have a WRT610N v2 with current firmware. The hard drive is a Western Digital Elements formatted to NTFS and already has music and photos so that other computers in the house can view them. This setup was done awhile back, maybe even a year ago.
Anyway, I can map the network drive and see everything there, but then after awhile (minutes - maybe 10) of idle time, the network drive can't be accessed by any computer, either as the mapped drive (W or by clicking the WRT610N in the network tree. It's like it goes to sleep and can't be awakened by activity.
I have searched the forums here and at WD but haven't found a solution or even this exact problem. I did find a utility on the WD site that is supposed to fix/eliminate the short idle time, but it didn't seem to work.
I have the WRT350N router. to access my usb storage link from within the LAN it asks for user id and password as I want it. but to access it from outside my LAN it just connects without asking for user id and password. My guess is it has something to do with shares and how they are setup. I can't figure out how to set it up so it asks for user id and password when attempting to connect to my storage link from the net?
View 1 Replies View RelatedI have a Cisco Valet wifi router that works fine with my laptop and my computer that has a usb wifi adapter. The problem is that for some reason when I try to connect my moms computer to the router it can only connect to the guest router and when I try to connect to the regular router it just fails even when I use the correct password. I have tried uninstalling the driver and re-installing it for the usb wifi adapter for my moms computer (NetGear N150 USB Adapter) and its nothing works. Her computer by the way is an Acer Windows XP SP3 machine.
View 4 Replies View RelatedI have a wrt350n at home and it works fine but it has only one little issue. When I connect my lap wireless I cant see the other work group pcs but if I wire the laptop there is no problem. I use ip to share files and not net bios but sometimes it would be great to find all the pcs on the work group easily and not memorize all the ips.
Disabled firewalls, updated firmware, tried to change network ip... nothing solved. Have no problems at work with an WRT54G.
I am having issues with the WRT350n where I am getting an "No internet access" message. When I look at the wireless network connection I can see the wireless router and it says "connected" but when I scroll my mouse over the icon, it reads "No internet access". I try to access a webpage and it will not work. I originally had it connected and working properly in my home. However, I removed it and tried connecting in my office and started experiencing this problem. I did not run the setup using the CD provided. I just unplugged it from my home network and reconnected it to my office network, of course with a few passphrase changes and wireless MAC filters only allowing certain PC's to be able to access the internet. I double checked all MAC addresses of each device that I entered into the table and they are correct. All devices see the wireless network but cannot access the internet. Any suggestions? Should I re-run the installation using the CD?
View 1 Replies View RelatedI have my WRT350N setup. all computers within my LAN can access my usb storage device. I can not access my usb storage device using a computer outside my LAN.
if you log on to 99.225.89.229:8080 it will ask you for user id and pass word to log into my router.
if you try to log on to 99.225.89.229:21 it wont even connect asking you for a user id and password.
my guess is the router is not allowing port 21 to be accessed, but I'm not sure.
When upgrading with .bin file (v1.05.8) via Administration - Firmware Upgrade, it fails when status showing 76% completion.
View 4 Replies View RelatedI have a Linksys WRT350N which I am trying to use an app on my iPhone to connect to my server using the public/external IP of my cable modem. I have the necessary ports opened and also tried adding the server to the DMZ but no matter what I can not get the app to connect to my server via my external IP when I am on my WiFi. I can connect without any problems if I use the NATed IP on the server when my phone is connected to the WiFi. It also works fine connecting to the external IP if I am on any other WiFi or the cellular network (which shows ports are forwarded correctly). I just can't connect to the server when I use the external IP and I am on my WiFi network. This is annoying as I need to keep changing the app's settings back and forth between the external and internal IP whenever I am home or away. I am left thinking this is some kind of issue with the WRT350N not allowing local internal traffic to reach the external IP. Any way to resolve this, maybe by entering a static route?
View 2 Replies View RelatedI have a WRT54GC v2.0, that was working perfectly till yesterday.I cannot access the router no more, either thru cable nor wireless, all lights are flashing.I thought it would be the power source but i have measured it with my fluke multimeter and there is 3.5v, it is probably working well.
View 9 Replies View RelatedI tried to upgrade the firmware of my WRT350N but while upgrading my wife switched on the oven and.... yes, power down -> the upgrade has been interrupted. Now the router is no longer responding, it shows just the green power light on (not blinking). I tried all the resets I found googling (pressing the reset button for 30 sec, isconnecting power and reconnecting it again) but no way, there's no way to ping the router at its default address 192.168.1.1. All the leds are switched off (internet, usb, wireless, security) except the green power light. Is there another way to have it back or it is definitely lost?
View 6 Replies View RelatedHas anyone managed to access the Storage Link from the internet on the WRT350N router? I am on my second one and it still doesn't work. Also the configuration restore does not work either.
View 9 Replies View RelatedI have a Dell Wireless 1500 draft N adapter that only connects at G speeds in mixed mode. I tried N only mode and my adapter will not connect. I have tried N mode Auto and 40hz wide and nogo. I have tried TKIP + AES and AES and nogo.
View 1 Replies View RelatedI recently upgraded my internet speed service from my ISP (Brighthouse). They installed a gateway to replace their old modem, but I have had it bridged so it should act as a modem. Speedtest.net shows downloads on the order of 40-50 Mbps and uploads around 5 Mbps. If I try doing something interactively that pushes the speed and size of files (like flying over Google earth using my mouse to guide the direction and speed) my connection seems to hang. I have to reset the router (unpower and repower it) to get my internet connection to work. This has also happened when I quickly downloaded a series of large images - I click to get the next page fairly soon after the current page has finished downloaded. My router is a WRT350N.
View 6 Replies View RelatedBeen using the WRT160N for a while now and it works great except for one issue. Every few weeks the wireless can't be accessed by the other computers unless I change the SSID name. It was frustrating to figure out, but simply changing the name makes it accessible again.
View 1 Replies View Relatedautomatic firmware upgrade my E4200 can no longer be accessed.
View 6 Replies View RelatedWin7, wrt54gs,
It works sometimes. I imagine it has a noise problem since sharing files works, internet works. I cannot remember how to change channels on this router to save my life, though. What is special about sharing a printer?
So I have a WRT160N firmware v3.0 wired connection to my PC, and at least once a day my connection speed drops from 2mbs down to almost dial up speeds at 60kps. Just unplugging the router then plugging it back in seems to fix it every time. I've contacted my service provider and they say there's no issue on their end, and since I don't get this problem when I plug the modem directly to the PC I agree with them. I've done a factory reset and that didn't work. I've gone through the FAQ and can't find anything useful in there.
View 7 Replies View Related My ISP here at my mother's in Italy (www.teletu.it) gave me the following configuration:
1. Supported Protocol: PPPoE or PPPoA
2. VPI: 8
3. VCI: 35
4. Encapsulation: LLC (If not supported: VCMUX/NULL)
5. Modulation: Multimode
6. Authentication Protocol: PAP or CHAP
if I connect my laptop to the ADSL modem, it all works just fine and I can connect to the internet (as you can see )
HOWEVER, if I then try to configure my WRT54G v6 to use this internet connection (I NEED to be wireless here, or I won't be able to use my iPhone and iPad), there is no way apparently for me to configure the Encapsulation, Modulation, and Authentication Protocol above. I just upgraded my WRT54G's firmware, and am now running firmware Ver.1.02.8, 10/05/2009. I was hoping this would allow me to set these parameters, but I can't find a way.
I tried just configuring the WRT54G with PPPoE and the ISP's userId/password, but this doesn't seem to suffice, and I don't see any other settings I could try.
I have this WRT350N with me for a long time. It always worked well, and for a while I didn't used it (like 1 year). Last morning, I set it up and put it to work again and it worked perfectly, but in the evening the wireless stop working. Through cable, the internet works finely.
The light does not turn on or blink anymore. The router setup says that SSID broadcast is enabled. But I can't find the network, even if I type its name and password (supposing it was in invisible mode or something like that).
So I restored the router to its normal configuration, and once again the wireless does not work. Is there something else I can do to make the wireless work again?
I just bought a Westell modem 6100 model online, and when I try to change the profile, I get a message saying: The server 192.168.1.1:80 requires a username and password. The server says: Modem Secure."
View 12 Replies View RelatedI was excited to learn that USB printer support was added to the E4200. I'm disappointed to find that the USB printer option that is available in firmware version 1.0.02 requires Cisco Connect software. There is no version of Cisco Connect for Linux. I was hoping that this would allow the printer to be shared among my Win7 desktop, Win7 laptop, and my Linux desktop running Ubuntu 10.10. No such luck. WIth the printer connected to the router I can print with any one computer. My previous configuration had the printer connected to my WIn7 desktop so that desktop had to be turned-on to print. The bottom line is that I still can't print from the Linux box without turning on the desktop machine. Cisco please provide a way to connect to the printer without using the Connect software! Or provide a java version that can be run on any OS.
View 4 Replies View RelatedI just bought a Westell modem 6100 model online, and when I try to change the profile, I get a message saying: The server 192.168.1.1:80 requires a username and password. The server says: Modem Secure."
View 1 Replies View RelatedLately, I upgrade the firmware on my router. A linksys WRT54G. In order to access the router I had to do a manual reset to factory settings. Post upgrade, for some reason I couldn't access the internet. I tried everything for hours and finally through sheer luck of unplugging every cable and ever power lead and plugging it back in, it started working.
However, lately I've found that the only computer connected to the internet via eathernet cable is loosing connection intermittently. Also we seem to get constant huge spikes in latency and very inconsistent speed. Unplugging the router and plugging it back in again seems to solve this problem temporarily, but requires toggling of power multiple times a day. Also I had what I believe was an IP address conflict, or lack of an IP address once, but using the windows troubleshoot errors fixed that by resetting my wireless network card. (This was on a 2nd machine)
[code]...
Trying to install the Linksys AE1000 wireless adapter on Windows 7 x64. So I follow the instructions. insert CD. Insert adapter.The i get this error:
"Linksys Wireless-N Router requires that wireless connections are to be managed by the Microsoft Windows Wireless Connection Manager. Some laptops and computers are pre-loaded with a different wireless connection manager which prevents your Valet or Linksys Wireless-N Router installation from loading. If this is the case, then you will need to disable or turn OFF the other wireless connection manager, and enable the Microsoft Windows Wireless Connection Manager instead."
What manager? This is windows 7, I'm not using any third party wireless utility so I don't understand why I'm getting this particular error. If windows wireless connection manager is off, how do I enable it?I've always managed my network setting through the Network and sharing center,I've tried:
(1) sweeping registry files before install(2) Plugging in AE1000 first and manually installing drivers
When I did this, the device shows up successfully in device manager and the driver installs smoothly, however when I go to network adapters, the AE1000 is listed as disabled. I tried enabling it but to no avail. Running the network diagnostics claims the driver doesn't work despite the fact that it installed successfully.
After several restarts and disabling/re-installations I recieve the same error.The end goal is to connect the AE1000 to a Cisco E3000 router.
I am looking to get access to an external hard drive that I have set up on my wireless network.When I try to do an automated Windows backup (off my Vista based laptop files) on to an external hard drive which is connected to my wireless network (through a Belkin router) I am being asked for a user name and password to access the connected hard drive on the network. The thing is that I don't remember setting up a username and password for the hard drive at all. I can paste single files mannually onto the external hard drive without being asked for a username and password. I did perform an automated Windows backup off my other Windows 7 laptop and was not ask for a username and password. where to find the username and password information ?
View 3 Replies View RelatedRegion : Australia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
I just upgraded from my factory default and found network sharing of my USB HDD was no longer working.It came down to two bugs in the latest firmware:Even though there is now the option to share without a password that option does not work and you still need a password.And that password is the factory default of "admin" even though I have set my own password.
I recently installed a Cisco X2000. Several PCs running Windows XP Pro connect wirelessly. Also, we have an Android device and iPhone connected to the wireless network. We have a network printer and network drive connected via wires to the router. Most of the time the router and cable modem features work well. However, every so often all devices lose wireless signal simultaneously. It is not possible to reconnect to the X2000 unless I unplug the X2000 and plug it back in. After this reboot, we can connect again. Obviously, this is quite frustrating. By the way, we get acceptable signal strength after the X2000 locks out however none of the devices (computers or phones) are able to connect.
View 1 Replies View RelatedI've read the various threads on here and tried all the fixes suggested and I still cannot get my PS3 to "see" the USB drive I've attached to my router.I can see it and access the files from a connected computer, but not the PS3.I've tried creating a share with one directory and sharing the entire partition with no luck. I've enabled all the FTP options with no luck. UPNP is enabled. I've tried setting up the guest account with no luck.I've tried restarting, unplugging with no luck either. I also went into the USB drive and reformatted and started all over again.My PS3 can easily see the other computers on the network, but I would like to use the USB port on the router to not have to have a computer running to stream music.Is there another menu location on the PS3 I should be using to locate the USB? Currently I just look under music or video and the other computers are there. Just not the USB.
View 1 Replies View RelatedSince the upgrade by Cisco I can only see Win7 PC's on the network. I can not see the USB drive attached to the E4500, nor can I see my Media server which is Linux based nor any Win XP computuers.
View 9 Replies View Relatedi have a 2tb seagate expansion formatted ntfs. i am primarily a linux (ubuntu) user, but when the drive drops off, it cannot be seen in any os and it doesn't show up on the router setup page.
View 6 Replies View RelatedI picked up an EA4500 about a month ago and so far it works great! I would like to purchase a USB hard drive to plug into it, but noticed the officially supported drive list on the support site seems to be a little out of date. good "current generation" USB hard drive that works with this router?
View 5 Replies View RelatedIm having trouble with my E3200. The router is working fine in all areas, with the exception that I cannot get my PS3 to detect the shared USB drive that is connected to the router. The drive is detected /mapped on the connected Windows desktop, but files/folder/drive is not appearing on PS3. The PS3 is connecting successfully to the router, as I have a strong internet connection. I believed that the E3200 would be able to share the USB drive with my PS3 for media file streaming... Or have I not done something correctly in the settings?
View 3 Replies View Related