Linksys Wrt160n V3 - Cannot Connect To Internet Through Router?
Sep 14, 2012
no devices on my network can connect to the internet through my router if it through WiFi or through Ethernet.if i connect directly to the modem i can connect.I can connect to the router configuration page but nothing else.i am running windows 7 and the router is a linksys wrt160n v3. internet,WiFi, and power light are all on the router.I have power cyceld the modem and reset the router with nothing changing
ipconfig /all information connected to router (no internet acces)
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.[code].....
I have recently changed the name of my network, as well as the password for the network.All of my devices (Android tablet, iPod touch, Macbook Pro, Laptop running XP, Xbox) are connecting fine except one desktop running Windows Vista.This computer is giving my a local connection, but says it is not connected to the internet.When I try to access the router's control panel from this computer, it says that it cannot connect.The router is a Linksys WRT160N with the encryption type set to WPA2 Personal.The computer is connected to the local area network, but says the router is not connected to the internet.It is able to ping the router, and is sending and receiving packets.Here are all the network settings for this computer, currently (connected to the computer via Ethernet from wireless router): [code]
Today, suddenly my internet went down so I checked up on it and I found out that something might be wrong with my router. I can connect just fine if I connect my computer with the modem directly but when I plug the modem to the router, I can connect to the router but it doesn't give me any internet.
I cannot get into my Linksys WRT160N router web page. I'm hardwire connected to the router. My computer is using DHCP IP addressing. The router has assigned it the standard 198.169.1.100. I can ping the router at 192.168.1.1. Wireless and Wired connections through the router to the internet are OK, no trouble accessing internet sites. Linksys advisor displays the router address as 192.168.1.1, so it has not been changed from the factory default. The advisor shows my networked devices clear back to the internet and claims there are no problems. After entering 192.168.1.1 into IE, IE appears to connect and is waiting for the router to respond. After a few minutes, it times out with failure to connect message. I've tried Safe mode with internet access, I've temporarily disabled my Windows and McAfee Firewalls, and the McAfee virus scanner. All to no avail.
I'm having an issue getting my tv to start connecting again to the wireless router.Have tried pin setup (timed out & didn't connect...attempted at least 10 times in this fashion)Have tried entering the password (router seems to refuse the connection to the tv)About a month ago, I was in the Network Magic Map & it looked like one of the laptops had been cloned, so I removed it from the network.
I have two computers on hard line and two laptops. All computers on the line work fine and flawlessly. But when I try to connect the laptops to the computer, they say there's a problem with the certificate. Both detect the connection, and with strong enough signal strength. I've tried WPA and WEP encryption methods, and disabling encryption methods. All had no change. I believe the problem lies with this Wi-Fi Protected Setup stuff, which I have no clue as to what the hell it's supposed to do. I've tried disabling it by turning it to manual, which all computers then lose internet connection entirely. Browsing the FAQ's, I havn't found a solution. I've been working on this thing for a solid 7 and a half hours straight, and phone support is trying to make me configure static IPs, which proved extremely inconvenient in the past.
I just bought a Linksys WRT160N router. I pop the installation disk in my mac book pro and walk thru the installation procedure successfully.But I can't connect wirelessly from my MacBook Pro (running mac os x 10.5).It sees the router and I did type in the password correctly (i copy from the text file generated by the installation procedure), but I keep getting 'coonnection timeout'.
I need to go two ways in my house to improve the wireless signal. Do I just run ethernet cable from the router to the access points? Do i then setup each AP?
I have" a WRT160N but I guess we had a power outage while I was on vacation and now I can't connect to my old network I set up.I see the Linksys internet connection and I can connect but its not the password protected one I set up. When I go to "manage connection" I can see the old "house" connection but can't connect
I've been using a WRT160N for a couple of years now with no problems with any of my devices. I have a couple of certain devices (a DS and a PSP mainly) that utilize 802.11b and have been working perfectly up until now.
All of a sudden it seems like the router has decided all by itself to no longer allow 802.11b devices to connect to it, despite it being configured in mixed mode. (b/g/N) I've tried tinkering around with it, switching between Mixed and BG-Mixed, changing the channel to something more common and restarting the router, but I can't connect at all on these devices.Model: Cisco Linksys WRT160N v3.Firmware version: 3.0.03.
Every time I try to connect to the admin page of my router, I get "The connection to the server was reset while the page was loading." This happens with FIrefox 11, and started when I upgraded to 8 or 9. A machine running FF 3.6 does not exhibit this problem; I get right in. What IE 9 says is "Internet Explorer cannot display the webpage" (after complaining about the expired certificate).
I ran Wireshark to see if I could learn anything, but all I could figure out was this: https handshake was OK. First TLS packet is received by router, which then immediately issues a reset and ends the connection. I don't know why.
have I got a screwed up configuration (or router)?
Windows 7 laptop does not connect to Wiress router WRT160N. It used to connect automatically for years when laptop is booted.Now Windows troubleshooting gives message to reboot wireless router. It connects automatically when the wireless is rebooted. This issue occues when the router is ON for long time ~ 12 hours or more.
I've been searching and searching the internet and I have never found a CERTAIN answer for if the linksys wrt160n v3 router will work for the ps3 or not. I want to know for sure if it will work because I know that is it sbackwords compatible with g/b/a networks but I am a newby at this stuff.
Purchased today 26th March 2012, used CD first as warned, followed procedures, will not connect to WAG 160N modem router. WAG160N has MAC restrictions but MAC of WRT160N added, both in wireless and as a computer. Still won´t connect, gets to 85% in wireless connect mode then fails, gets to stage 4 of router recognition and fails, saying check cables. Cables changed to know working ones, still no success. Tried pinging 192.168.1.1 direct from computer with no success, no access to router log-in page at all. WAG 160N has no problems.
My Linksys WRT160N wireless router stopped working all of the sudden. When I connect to the internet wirelessly my laptops say I have full signal but "No Internet Access." None of the 4 wired ports on the back of the WRT160N router give me wired internet. The only way I can get internet is to connect the wire to my internet modem
While trying to add my kindle fire (unsuccessfully) I lost all internet connections, now my laptop won't connect. I reset the router and and can see my wi-fi account but when I try to use on my PC and laptop it won't recognize it.
This was for a WRT160n v3.0.02 I looked up several suggestions online and decided to update the firmware to v3.0.03 This seemed to only make it worse as I could no longer connect, and when I turned the router off and back on it would allow me in for about a minute and drop me right away.I started tweaking with the settings, and came across some posts here such as this one, started tweaking with the channel settings and everything. Nothing. If anything I somehow made it worse since now instead of dropping repeatedly it wouldn't connect at all except for about a minute after restarting router, then it would drop completely (I would either get the limited access notification or I simply couldn't connect and windows said to unplug the access point. I recalled I had another Linksys router that I wasn't using in storage, a WRT54G2v 1.0.01 so I set that up, no problems... at first. All other devices picked it up right away, but once again, my new laptop decides it's too good for the freaking network and drops it repeatedly telling me there's a problem with the access point.
So at this point I'm thinking it might NOT be my network, but my wireless card or something, I uninstalled and reinstalled, updated drivers, (I use a Realtek RTL8723AE Wireless LAN 802.11n PCI-E NIC) I even came across this article and disabled browser service and NETBios (including all other devices on my network). It brought back the network on my laptop for a bit, only to smugly come crashing down again.
specs: linksys router wrt160n v3, verizon modem gt701c, windows xp service pack 3, verizon DSL, southern california.I have been able to connect to the internet directly through the modem only...but i need my wireless back working. I've reset my router a few times recently trying things i've read on forums from people with similar problems. The most recent thing i did was RESET the router -> connected modem/router/computer properly -> turned them all back on in the proper order -> check to see if websites would open. They didn't so i tried doing this, which was suggested...i plugged the router into the computer and enabled MAC address and then pressed the Clone MAC address button and saved....then I tturned everything off again and rebooted everything again in the proper order and still couldn't load any web pages. Here are my IPCONFIG/ALL read outs for both when i'm hooked up with the router & modem (which isnt working) and directly to the modem (which is working) this is the one with the router & modem:
C:Documents and SettingsOwner>ipconfig/all Windows IP Configuration Host Name . . . . . . . . . . . . : shakas Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown
[code]....
My modem and wireless were working fine for years...and then recently without me doing anything my modem kept dropping connection and the internet and dsl lights kept flashing and then going back solid....so i'd be connected for a few minutes and then they'd start flashing again over and over all the time. I finally called verizon and then had me fiddle around with stuff...followed all their directions...but ended up only being able to connect while directly connected to the modem. Even then, the modem was still losing connection and getting it back. (i was supposed to schedule a house call for a tech to check it out, never did) Over a couple weeks the connection ended up getting better on its own, so now it pretty much never drops out anymore. (almost) i've reset my modem, i've reset my router....i just still cant seem to get websites working with my modem and wireless router connected.
I recently changed the security mode on my router from WEP to WPA2 Personal. However, since that change, I've noticed that the wireless devices, 2-laptops, are intermittently loosing their connections. . I don't know if it has anything to do with the security mode change, but I don't want to go back to WEP for obvious reasons.
I've recently purchased a WRT160N router, and I'm using it in conjunction with a WMP54G wireless PCI card. I've set the router up to my requirements, and can get a stable wireless connection.. but internet speed seems excessively slow. While I'm able to get up to around 4MB/s transferring files over the network, running speed tests, it consecutively shows my download speed to sit around 400KB/s, whereas I'm able to get a steady 1.1MB/s on another desktop that is wired. Disabling the LAN adapter on that computer, and connecting via wireless, brings down the speed that that computer is able to get to around 400KB/s as well. Hence, I don't think it's my wireless cards, but something to do with the router itself.I'm also experiencing lag spike issues in online games, which I can only attribute to the current wireless setup, because I've previously had no issues with it. All relevant ports are forwarded, so that is not an issue.After doing some Googling on the subject, someone had suggested running SpeedGuide's TCP Optimizer, and changing the RWIN - I ran it, and set it to the 'optimal' settings, and after a reboot the wireless seemed fine - I was getting just a tad under what I should (about 950KB/s).. but after a short while, it just went back to 400KB/s. After further investigation, it seems that Vista automatically changes that RWIN value to optimize network traffic.. but I never had this issue with my old wireless gear, so I can only assume that the way Vista is reacting is based on the way the router is interacting with it.
Everything was going great until tonight. I can connect to the internet fine wired. Wireless devices can connect to the router, but cannot access the internet. No changes were made to the unit. Updatae firmware to 1.02.11 but that did not fix the issue.
I had an old MS DSL1000 that was upgraded by Qwest to an Actiontec GT701 (not wireless) modem. If the GT701 is plugged directly into the PC, the internet works fine. If it is connected from the ethernet port into the WRT160N router, the LAN works but not the internet, even though the internet light is a solid green on the GT701. I've read about port forwarding and DMZ, but still not positive if I should do one or the other, much less on how to go about setting either of them up correctly.
How do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).
I am unable to connect my Ipad3 to my home network (WRT160N router). It has been working for the last 8 months, and stopped working after I installed Direct TV App on Ipad..It detects the network, but not accepts the PW.... I have multiple wireless devicess connected to my network without any problems..The funny thing is that my neighbor brings his ipad to my house and he is able to connect..My ipad connects to any other network...just not my home network.. I contacted Apple who spend hours with me on the phone and suggested doing a full reset on the ipad, but still did not solve the problem..I called and already paid for linksys support ($62.95) who spend hours with me on the phone, but suggesting: "maybe you need to buy another router"...REALLY!!!! Again, I have 3 Smart TVs, Xbox360, and Wii, that are connected to the network just fine .even my neibor comes with his Ipad3 and connects to my network just fine......and I can connect with my ipad to any other network without any problems... BTW, I have already removed the DirectTV app from the ipad....but I still cannot connect to my network..
We have a home use WRT160N router linked to a PC desktop and two wireless laptops, Yesterday bought a new I-Phone, but could not link to my network (entered the security key many times). I accidentally connected to computer fix it firm that linked to my PC and wanted a large sum to fix the problem which he said was due to large number of temp?? internet files and once removed he would change the IP address of the desktop computer? Is this diagnosis logical and can I do it on my own. The router is definetely working - both laptops access the internet and I was recently able to hook up a Samsung Blu-Ray player using the same security code I used for the I-Phone.
I have a Wrt160n router and a Motorola sb120 modem (provided by comcast after my original modem got fried by lightning, no I didn't have my router hooked up when that happened), I have been having trouble trying to get the modem to send the internet signal to my router. I have tried mac address clone that was suggested on this forum for someone with a different router but still no internet to my computer, its all hooked up through Ethernet cables, the computer I have it hooked up with a hard line is running windows seven. When I plug the modem straight to the computer it works and I have internet but when I hook up the router between them it has no internet.
why i can't add a new policy. I can't fillin a policyname or change the status from disable to enable. I have model V2 with firmware v2.0.03 build 007Jul 2, 2009
I connected the Router to the modem, and all the wired connected PCs were working perfectly.But then, i went to the setup page to configure the Wireless settings, and as soon I changed the SSID name, the connection internet connection droppedThe only way i had to fix this was by making a Hard Reset.after that, I also tryed changing values and settings from all the configuration tabs, and the wired connection was working properly, but as soon i changed any value from the Wireless tab, the internet connection dropped (even, in the diagnostics section, i could not do a ping to google. It says unknown host).
I own the linksys wrt160n v2...It has latest firmware 2.03 build 9...After installing this firmware i have noticed the internet speeds have reduced,the router requires frequent reboots to make it stable..
i used to have firmware version 2.02 build 15...It was stable unlike the current firmware...i cant find the old firmware anywhere...how do i revert back to old firmware?
