I recently changed the security mode on my router from WEP to WPA2 Personal. However, since that change, I've noticed that the wireless devices, 2-laptops, are intermittently loosing their connections. . I don't know if it has anything to do with the security mode change, but I don't want to go back to WEP for obvious reasons.
View 9 RepliesHaving problems with my wireless router, dropping and keeping connection active. For some odd reason I keep dropping connection either wireless or wired. I have a total of 5 items going through this router. 2 of them are wireless and the other 3 are wired. The wireless items are a desktop computer that is using the Wireless USB adapter to get online. Sometimes it drops and most of the time it doesn’t have any problems. I have a laptop that sometimes the connection goes from strong all the way down to no connection at ALL. It starts at 54MBPS to down to the RED X over the wireless manager. Forgot to mention both of these machines are Windows XP. If I reboot the laptop, it comes up without any problems.
Sometimes I tell Windows XP to manage the Wireless connection and tell it to disconnect and re-connect again, it goes. Now for the wired items, I have 2 gaming systems and another computer plugged directly up to the router. For some odd reason when I double click on the internet, on the computer that is hooked directly to the router, it says page couldn’t be found. I know that there is connection and there is nothing running in the task tray except for the Anti-Virus and Firewall. The browsers that I am using are Internet Explorer 8 and Mozilla Firefox 3.0.10. Also checked on the back of the machine to see if I have link lights and everything is flashing. Finally, when I click the homepage or refresh button about 2 or 3 times, it goes through.
think that I am overloading this Router and it can’t handle it. I might have to look into sending "Keep Alive" packet setting on the router.
I've got a router in room where my cable modem comes in. In center of house, I have another router, N Ultra Range PLUS, WRT160N.
My laptop, which I use in front room near that middle room router and my husband's desktop, also near that middle room have no problems. My desktop which is right next to the main router in back of house (where the cable modem is), has the weakest signal. I guess that's because the WRT160N is further away from it and has two walls to go through. But most of time signal was good - just not as good as the other two computers. And even when signal was Low, it never dropped connection.
Recently I got a new smart phone with WIFI. Anytime I have turned on the phone and used it, I often then have to refresh my wireless signal or reboot computer because it loses the connection. I read somewhere on internet that this may be because of the additional device but again, it doesn't effect the other two closer computers.
specs: linksys router wrt160n v3, verizon modem gt701c, windows xp service pack 3, verizon DSL, southern california.I have been able to connect to the internet directly through the modem only...but i need my wireless back working. I've reset my router a few times recently trying things i've read on forums from people with similar problems. The most recent thing i did was RESET the router -> connected modem/router/computer properly -> turned them all back on in the proper order -> check to see if websites would open. They didn't so i tried doing this, which was suggested...i plugged the router into the computer and enabled MAC address and then pressed the Clone MAC address button and saved....then I tturned everything off again and rebooted everything again in the proper order and still couldn't load any web pages. Here are my IPCONFIG/ALL read outs for both when i'm hooked up with the router & modem (which isnt working) and directly to the modem (which is working) this is the one with the router & modem:
C:Documents and SettingsOwner>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : shakas
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
[code]....
My modem and wireless were working fine for years...and then recently without me doing anything my modem kept dropping connection and the internet and dsl lights kept flashing and then going back solid....so i'd be connected for a few minutes and then they'd start flashing again over and over all the time. I finally called verizon and then had me fiddle around with stuff...followed all their directions...but ended up only being able to connect while directly connected to the modem. Even then, the modem was still losing connection and getting it back. (i was supposed to schedule a house call for a tech to check it out, never did) Over a couple weeks the connection ended up getting better on its own, so now it pretty much never drops out anymore. (almost) i've reset my modem, i've reset my router....i just still cant seem to get websites working with my modem and wireless router connected.
I have Linksys WRT160N v2 wifi router that I have been using for over a year now, till two months back I was very happy with the router, speed was good without any signal issues though in last couple of weeks I have noticed that the router has started to create problems like the browsing will stop it self for a few seconds without any reason (specially I notice this when I am on youtube playing a video that will stop after 2 or 3 minutes).
View 7 Replies View Relatedi bought a WRT160N router
I connected the Router to the modem, and all the wired connected PCs were working perfectly.But then, i went to the setup page to configure the Wireless settings, and as soon I changed the SSID name, the connection internet connection droppedThe only way i had to fix this was by making a Hard Reset.after that, I also tryed changing values and settings from all the configuration tabs, and the wired connection was working properly, but as soon i changed any value from the Wireless tab, the internet connection dropped (even, in the diagnostics section, i could not do a ping to google. It says unknown host).
Currently running Windows 7, with internet explorer. I have most recent firmware installed on my e2500. The unit drops wireless connectivity on an intermittent basis. Sometimes after 5 minutes and sometimes after 20 or 30 minutes.
View 9 Replies View RelatedI had the 2 Wire Box that received TV and internet. Called my ISP and they gave me this access point to use instead. I hooked it up and it was fine for about 2 weeks. Suddenly for no reason it started dropping. Noticed it first when online gaming on my PS3. Checked laptop and all wireless devices down. Takes about 30 seconds.
View 1 Replies View RelatedWired connection to the router works fine. But it drops all the wireless devices (PC, phone, tablet) multiple times each day, sometimes only 30-60 minutes after reconnecting. Power cycling the router "fixes" the router and allows reconnection. There are 2 topics in the FAQ section that looked good: Getting poor or no signal from a wireless routerTop causes of dropping wireless connection on a Linksys routerbut clicking on those does not bring up anything.
View 9 Replies View RelatedSet up: Router: WRT110 1 computer connected via ethernet cable 1 computer using a wireless nic card from cisco
The problem is thus: if the first computer is actively using the internet (even activities as mundane as browsing one's email) the computer connected wirelessly will lose its connection to the internet yet maintain its connection to the router. Both can be actively using the internet, but the wireless will seemingly at random drop internet access (usually in 30-120 minute intervals).
The computer connected via the ethernet cable was unplugged for a week and during that time the wirelessly connected computer was used extensively and did not lose connection once.
I don't understand how to even frame this problem in a concise manner, much less seek information as to how to resolve it. It's seemingly giving all priority to the computer connected via ethernet but I that's just intution speaking.
I have a WRT54G conected to a desktop through a wire, and conected to a laptop wirelessly. It starts working fine, and after a while i get no internet connection in my laptop nor my desktop. After this happens i disconect the power source from the router, i conect it back again and it starts working.
View 9 Replies View RelatedI've been using my Linksys WRT54GC for couple years now, and only recently have I started to have significant issues with the device. I'm using a 2012 Macbook Pro, and my internet connection seems to be randomly dropping every now and then. Sometimes it works just fine for couple of hours only dropping once or so, sometimes it starts dropping literally every few seconds. What I usually do is quickly restart my wifi and the connection comes back right away. I also tried not doing that, and the internet connection tends to come back up after a minute or so.
I have read countless topics, also tried many things: changing MTU, the thresholds in router settings, security modes (it seemed to have worked fine after I changed it to WPA, not anymore though. I'm using no password now and it doesn't fix the problem either), changing the channel (my strongest signals around are on channel 1 and 11, thus I left mine on 6), I even reset the router today (held the reset button for 10 seconds~) but it didn't work either. I didn't upgrade the software since I heard stories about the software available on this site being corrupted or something, bricking the router, which is the last thing I'd want (I'm running on 1.00.7 now).
I have the impression (but it's just an impression, it might as well not be the case, and just me trying to find out when it happens, since it's not always that it breaks the connection while doing that) that it breaks the connection on high load, I mean when I'm for example using skype and facebook, and then try to go on reddit at the same time - the reddit webpage won't load, and the connection is lost after few seconds. But it also started dropping every few seconds while I was playing an online game and skyping at the same time today, which isn't a particularly huge problem for a 23Mbps download and 1.5 upload speed internet I suppose, and which it never did before. I have never had such issues with my PC using a Linksys USB adapter. The connection would drop from time to time when, for example, accidentally going on pages with lots of thumbnail pictures, or trying to load 15 tabs of jpgs at the same time, it was never that much of a problem really though, I just thought it's normal.
Set up:Router: WRT11.1 computer connected via ethernet cable.1 computer using a wireless nic card from cisco.The problem is thus: if the first computer is actively using the internet (even activities as mundane as browsing one's email) the computer connected wirelessly will lose its connection to the internet yet maintain its connection to the router. Both can be actively using the internet, but the wireless will seemingly at random drop internet access (usually in 30-120 minute intervals).The computer connected via the ethernet cable was unplugged for a week and during that time the wirelessly connected computer was used extensively and did not lose connection once.
View 2 Replies View Relatedever since i had a power failure losing all power in my apartment, my router has begun regularily losing connection to the internet, I have to go into the router and renew ip address which is quite annoying
[code]....
my e4200 wireless. I have internet connection speed of 40mb and I have epc 3925 working in bridged mode as modem and E4200 as router. When I connect my laptop with wire on e4200 I am getting 37-38 Mbps on speedtest.net which is perfectly fine. But on wireless I am having a lot of dropping of speed: I have 2mps then jumping to 5-6 Mbps and so on it never goes more than 5-6 Mbps. When I disable WMM Support in QoS I am having perfectly constant 20mbps but... I have only g network 54mbps. [code]
View 9 Replies View Related I've recently purchased the EA3500 dual band wireless-N router to replace my old and somewhat tired WRT54GS. The old router worked, I just decided to upgrade to wireless-N since all of my devices are now capable.My ISP is Comcast and I use a Motorola SB 6120 cable modem. After an extremely easy setup of the new router last week, I experienced one full day of glorious speedier network and internet traffic. However, roughly 24 hours after installation I started experiencing intermittetent internet connectivity issues. As in - the cable modem is accessible for 2 minutes and then can't be found for 2 minutes, repeat forever.
After multiple different troubleshooting steps, including rebooting both the modem and the router together, separately, and releasing and renewing the router's IP Address through the router's admin page, I finally ended up resetting the router back to factory defaults and letting Windows 7 guide me through the re-installation rather than using the provided "easy setup" CD from Cisco.
This seemed to have worked, but 2 days later, my "every 2 minutes" issue returned.
Something important to note here is that all of my devices - both wired and wireless - are able to communicate with each other without issue. For example - while I have no access to the cable modem, I am able to stream music from a wired desktop through a wireless laptop to a wireless receiver connected to my TV. I am also able to access the router's admin tools during my connectivity issues.
My wireless router will work for 6- 8hrs then drop the internet connection. I have to cycle the modem and router several times to restore the connection. I am also using a Netgear Access Point.
I am using:
Charter High Speed Internet
Motorola Modem
Cisco Model WRT120N Router
SETTINGS
Mode- Mixed
Channel Width- Auto 20MHz or 40MHz
Security- WPA2 Personal
SSID Broadcast- Disabled
Firmware Version v1.0.04
Connection Type- Auto Conf DHCP
Beacon Interval - 50
Fragmentation Threshold 2304
RTS Threshold 2304
All other setting are at factory default.When I unplug the modem from the router and plug it into the desk top I have internet service.
i am a total n00b when it comes to wireless routers etc,.. i bought this router [E3200] about six mths ago, it has been working just fine untill a couple days ago, wher i woud be on the internet and all of a sudden, the internet connection drops, i am using a cable modem [ARRIS TM722G] ,i did a reset on the e3200 and put restore the settings that did last over night
View 9 Replies View RelatedI have a home network with a Linksys E4200 connected to the ISP's fiber box. The problem is that when I'm connected to the Linksys, either wired or wireless, the connection to the internet will drop after what seems to be a random amount of time (normally anywhere from 2-10 minutes). I can restore the connection by doing any of these things:-reboot Linksys-disconnect and reconnect cable from router to fiber box-if on wireless connection, make changes to the router wifi settings, like change the wifi channel.The internal network stays up, and I can ping both the internal and external ip of the router, but not the fiber box. I have also had the same behavior with an Edimax Wifi AP and less frequently with a Edimax router (once every 1-2 days). I have done everything I can think of:-changed the wifi channels-changed the ip ranges, subnets, turned router DHCP off and back on-booted the fiber box-changed cables-updated all routers to the latest firmware, the network cards with latest drivers...and loads other things that I don't remember right now. For the wifi side of things, there are no other networks in range that could interfere. The same problem occurs on both my and wife's Win 7 laptops and on the iMac (latest OSX). Here's a fun detail: while the Linksys has lost its connection to the internet, I can still access the internet through the old Edimax router connected to the same fiber box, either wired or wireless.
View 1 Replies View RelatedI've recently picked up a E4200 to build a dual band network which is targeting to link up (TV, media server, ps3, laptops) then (maintaining phones etc which only has b/g). While currently only laptops.Before doing any of these I have another cisco modem router DPC3825 which worked fine with giving wireless access.I first attemped to leave the modem router has is and connected the E4200 (ethernet 1 to internet), and changed ip to x.x.0.1 and x.x.0.2 while disabling wireless on the dpc3825 and the DCHP on the e4200 and have default gateway to x.x.0.1. My laptops can connect to wireless on E4200 but it couldn't get internet access.
Then I tried turning the modem to bridge mode & resetted E4200 (factory setting x.x.1.1, auto DHCP), and then connected my devices to both wireless bands. At this point I see router status obtained ip from ISP and Internet reached full speed per ISP's mark but the connection only held up for about 1 minutes. I noticed all the devices still maintained connection to router wirelessly but the router loses internet connection (lost the ip and couldn't get it back).
I have a problem with my wrt160n and l2tp connection. I setting up router to l2tp VPN connection and speed of internet is down, and connection with my router interrupt very often. How I can fix it all?
View 7 Replies View RelatedI have speed 12M when I connect wrt160n v3 through l2tp, my speed down to 4M-5M. When i connect modem directly to computer I get speed 12M.
View 1 Replies View RelatedI had a secure connection, after trying to change the passsword, it now is unsecured. I was trying to connect a new Ipad to my router but I have failed miserably.
How can I get my router a password and then use that password to connect an Ipad to my home network? I reset the router, but the connection is unsecured, I can't figure out how to get it back.
I upgrade the firmware to Version: v1.52.0. The connection by wired is very good, i haven't slowness in internet. But if i'am connect by wifi, the website are very slow to load, and i can't see video on youtube without waiting.
I test without configuring the wifi (no security)
I got an WRT160N,when I had 5mb connection it was working normal,but since I changed to 10mb,it downloads at 40kbp-100kbp,The connection is very stable,but the speed its very slow.I try to download the firmware but its with .bin extension and I don't know how to open it.
View 9 Replies View Relatedhere is what I have:
A) Sonic Wall @ 192.168.1.215
B) Linksys Switch (WRW248G4P) @ 192.168.1.254
C) Linksys Router (WRT160N) @ 192.168.1.202 (Disabled DHCP Server)
D) Linksys Router (E2500) @ 192.168.1.203
E) Windows Server 2003 @ 192.168.1.200
F) There is also a Router @ 192.168.1.201 that runs DD-WRT that has an enabled DHCP Server.
It goes something like this
i) A - B --ETHERNET-- E
ii) A - B --ETHERNET-- C
iii) A - B --FIBER to another building, then ETHERNET -- D
Everything connects to the internet, but (D) on (iii) doesn't allow connection to the server (E). What can I do to make this work?
Often my router drops connection to all my devices. Multiple times a day. It's only for a minute or so, but it's annoying. I'm using a Linksys Wireless-N router (WRT160N) with WEP encryption. I'm running two Windows 7 laptops, LG BluRay player, Apple TV, Xbox 360 (Wired) iPhone 4, and a iPad 2. It doesn't matter if I'm browsing the web, watching Netflix, or playing a game, the connection gets lost. As we speak it happened again. I have no clue on what to do. I've reconfigured it multiple times. Firmware has been updated months ago.
View 6 Replies View RelatedI am having problems after installing the ae2500 adapter in my win 7 machine had to remove malwarebytes and avg to get it to work but now it constantly has problems dropping the internet connection. I have to disable the adapter then enable it to reconnect to the internet. Are there other compatibility problems with this setup that I need to address?
View 1 Replies View RelatedAs of last night my router has been producing slow connectivity when multiple users are connected to it, but it's perfectly fine when only one user is connected. I am on a laptop myself, but we also have a second laptop and a desktop where the modem and router are set up. I have upgraded the firmware so that is up to date. We have Comcast Fiber Optics so my internet speed is normally quite fast even when all of my computers are connected.
I am using DHCP Configuration. My Channel Width is set to 20 MHz and I am using Channel 11. The Security Mode is set to WPA Personal. I had it on WPA2 Personal but I read that changing to WPA Personal might work and so far it doesn't seem to have done anything. I set the Beacon Interval to 50, Fragmentation Threshold to 2304, and RTS Threshold to 2304. Everything else is set to the default factory configuration.
Just today I received a notice that said "Windows has detected an IP Address Conflict", but ever since I reinstalled the Firmware it hasn't come back. I've rebooted both my laptop and the desktop to confirm it hasn't come back as well. I've tried everything that I could think of including reconfiguring my router and restarting my modem as well.
I have been spending days !!! trying to resolve why my laptop pc disconnects frequently from its wireless connection. No discernable pattern to disconnects, totally random. Happens in cycles of disconnect/auto reconnect or will go hours of stable operation. What I have noticed is tht the connection speed seems to vary, from a hig of 54.0 Mbps to as low as 2.0 Nbps. At same time the desktop pc (hard wired to modem) stays connected at 100 Mbps.Using RCA modem, WRT160n v3 router.
View 2 Replies View RelatedComcast had us unplug our modem in order to upgrade to their new faster speed. now our wireless router won't work. We've reset the router twice. we can set up the wireless network but we cannot connect to it. The connection last for about 5 minutes and then we get an error, cannot read IP address. Comcast says it is not their problem and linksys says they can't assist either.
View 1 Replies View RelatedMy Linksys WRT160N wireless router stopped working all of the sudden. When I connect to the internet wirelessly my laptops say I have full signal but "No Internet Access." None of the 4 wired ports on the back of the WRT160N router give me wired internet. The only way I can get internet is to connect the wire to my internet modem
View 5 Replies View RelatedWhile trying to add my kindle fire (unsuccessfully) I lost all internet connections, now my laptop won't connect. I reset the router and and can see my wi-fi account but when I try to use on my PC and laptop it won't recognize it.
View 3 Replies View Related